Commit graph

9776 commits

Author SHA1 Message Date
Tom Rini
9dc8d155d4 Merge git://git.denx.de/u-boot-imx
- changes in pico-* boards
- fix imx6ull pinmux
2018-09-19 20:35:27 -04:00
Marek Behún
863949e383 board: turris_mox: Fixup U-Boot's device tree if PCIe connected
If PCIe Mox module is connected we want to have PCIe node enabled
in U-Boot's device tree.

Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
2018-09-19 09:00:39 +02:00
Baruch Siach
f26e379b31 dts: mvebu: mcbin: drop redundant SD slot node
Commit 61dccf73d3 (dts: mvebu: a80x0: Enable SD/eMMC interfaces) added
a redundant DT node for SD card slot. Drop it.

Cc: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
2018-09-19 09:00:38 +02:00
Marek Behún
0f6686e228 arch/arm/dts: Update Turris Mox device tree
Remove smi_pins definition since it is already in armada-37xx.dtsi.
Add assigned-clocks definitions to spi0.

Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
2018-09-19 09:00:38 +02:00
Chris Packham
2fd4284051 ARM: mach-mvebu: handle fall-back to UART boot
The bootROM in the Armada-38x (and similar) SoC has two modes for UART
boot. The first is when the normal boot media is blank (or otherwise
missing the kwb header). The second is when the boot sequence has been
interrupted with the magic byte sequence on the UART lines.

In the first mode the bootROM routine and error code register will
indicate that there was an error booting from the configured media in
bits 7:0. In the second mode there is no error to indicate but the boot
source is provided via bits 31:28.

Handle both situations so that kwboot can be used for both boot
strapping a blank board and for intercepting a regular boot sequence.

Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Signed-off-by: Stefan Roese <sr@denx.de>
2018-09-19 08:59:26 +02:00
Chris Packham
e0977297e8 Revert "arm: mvebu: fix boot from UART when in fallback mode"
This reverts commit e83e2b3900. This
prevents kwboot from overriding the hardware strapped boot source.

Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2018-09-19 08:59:26 +02:00
Baruch Siach
7e1d32208e arm64: mvebu: armada-8k: support environment in SD/eMMC
Detect the SD/eMMC boot device at run-time. Load the environment from
the boot deice, as well as save to it.

Leave the environment offset the same as in the SPI flash.

Make SD/eMMC 0 the default environment device when the boot device is
not detected.

Cc: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
2018-09-19 08:59:26 +02:00
Stefano Babic
0eee446ee8 Merge branch 'master' of git://git.denx.de/u-boot into master
Signed-off-by: Stefano Babic <sbabic@denx.de>
2018-09-18 16:53:55 +02:00
Dalon Westergreen
02d8d32591 socfpga: stratix10: fix sdram_calculate_size
Incorrect type of size variable results in 0 being
returned for sdram sizes greater than or equal to
4GB.

Signed-off-by: Dalon Westergreen <dwesterg@gmail.com>
2018-09-15 03:17:01 +02:00
Tom Rini
ecb10a41c9 Revert "ARM: da850evm_direct_nor_defconfig: Enable DM_SERIAL"
This commit is breaking several variants of da850, so:

This reverts commit 5f389201de.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-09-14 13:52:15 -04:00
Heiko Schocher
df158705a8 imx: imx6ull: fix pinmux input_val for uart5 rx pin
just try to bring up an imx6ull board with console
on uart5 and found, that input_val for pin
MX6UL_PAD_UART5_RX_DATA__UART5_DCE_RX is 7 and
not 5 on imx6ull.

With this patch rx works now.

Signed-off-by: Heiko Schocher <hs@denx.de>
2018-09-14 15:22:52 +02:00
Fabio Estevam
82a8a93327 pico-imx6ul: Convert to SPL
There are two versions of imx6ul pico SOMs: one with 256MB and another
one with 512MB of RAM.

Convert to SPL so that both versions can be supported. This patch
doesn't rework the clock initialization to avoid changing the behavior
in this same patch, so it will be cleaned up in future.

Currently only the 256MB is tested/supported.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2018-09-14 15:04:24 +02:00
Adam Ford
5f389201de ARM: da850evm_direct_nor_defconfig: Enable DM_SERIAL
With DM enabled, this patch enables DM_SERIAL and removes
the NS16550 initialization from da850_lowlevel since the driver
will take care of that itself.

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-09-11 21:42:41 -04:00
Adam Ford
668146128a ARM: mach-omap2: Don't initialize I2C if DM_I2C is enabled
boot-common.c checks to see if I2C is enabled in SPL, but
it doens't check for DM_I2C before initializing it.  This
will now only initialize the I2C is the DM_I2C is not enabled
to avoid initializing it more than once.

Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2018-09-11 21:39:02 -04:00
Adam Ford
abb205ded1 ARM: dts: da850-evm-u-boot: Remove redundant entries
With the re-sync from Linux 4.18, several entries in
da850-evm-u-boot.dtsi are no longer necessary, so this patch
removes them.

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-09-11 21:38:08 -04:00
Adam Ford
8e12559193 arm: dts: da850: Re-sync da850-evm.dts from Linux 4.18
Signed-off-by: Adam Ford <aford173@gmail.com>
2018-09-11 21:38:04 -04:00
Tom Rini
d1e15041ab Merge branch 'master' of git://git.denx.de/u-boot-uniphier 2018-09-11 08:50:10 -04:00
Lokesh Vutla
853f7f5018 arm64: dts: k3: Add u-boot specific nodes
Add the minimum dt nodes required to boot. These nodes
will get deleted as kernel gets these nodes added in the
main dts files.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2018-09-11 08:32:55 -04:00
Lokesh Vutla
ea8ad1d9b6 arm64: dts: k3: Add Support for AM654 SoC
Add initial DT support for AM654 EVM that runs on A53.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2018-09-11 08:32:55 -04:00
Lokesh Vutla
0911d95263 board: ti: am654: a53: Add initial support for am654
Add initial support for AM654 based EVM running on A53. Enable
4GB of DDR available on the EVM so that kernel DTB file
can be updated accordingly.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[Andreas: Added 4GB ddr support]
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
2018-09-11 08:32:55 -04:00
Lokesh Vutla
3980b16137 gpio: do not include <asm/arch/gpio.h> for ARCH_K3
As no gpio.h is defined in arch/arm/mach-k3/include/,
to avoid compilation failure, do not include asm/arch/gpio.h.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2018-09-11 08:32:55 -04:00
Lokesh Vutla
82f29fd513 armv8: K3: am654: Add support for generating build targets
Update Makefile to generate
- tispl.bin: First stage bootloader on ARMv8 core
- u-boot.img: Second stage bootloader on ARMv8 core.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2018-09-11 08:32:55 -04:00
Lokesh Vutla
e091832f25 armv8: K3: am654: Add custom MMU support
Add MMU mappings for AM654 SoC.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2018-09-11 08:32:55 -04:00
Andreas Dannenberg
c68721d93a arm: K3: am654: Unlock control module registers during init
By default the device control module registers are locked,
preventing any writes to its registers.
Unlock those registers as part of the init flow.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2018-09-11 08:32:55 -04:00
Lokesh Vutla
e00646099f arm: K3: am654: Add support for boot device detection
AM654 allows for booting from primary or backup boot media.
Both media can be chosen individually based on switch settings.
ROM looks for a valid image in primary boot media, if not found
then looks in backup boot media. In order to pass this boot media
information to boot loader, ROM stores a value at a particular
address. Add support for reading this information and determining
the boot media correctly.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2018-09-11 08:32:55 -04:00
Lokesh Vutla
f70b72e353 arm: K3: Update _start instruction
On K3 family SoCs, once the ROM loads image on R5, M3 resets R5 and
expects to start executing from 0x0. In order to handle this ROM
updates the boot vector of R5 such that first 64 bytes of image load
address are mapped to 0x0.

In this case, it is SPL's responsibility to jump to the proper image
location. So, update the PC with address of reset vector(like how
other exception vectors are handled), instead of branching to reset.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2018-09-11 08:32:55 -04:00
Lokesh Vutla
ed0e605124 arm: K3: Add support for AM654 SoC definition
The AM654 device is designed for industrial automation and PLC
controller class platforms among other applications. Introduce
base support for AM654 SoC.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2018-09-11 08:32:55 -04:00
Lokesh Vutla
586bde93eb arm: K3: Add initial support for TI's K3 generation of SoCs
Add support for Texas Instruments' K3 Generation Processor
families.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2018-09-11 08:32:55 -04:00
Masahiro Yamada
e39eed8f47 ARM: uniphier: remove ad-hoc clock enabling for EHCI
The MIO clock is enabled by default, and the STDMAC clock is
enabled by the clk driver.  The ad-hoc way to enable the clock
is no longer needed.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-09-11 20:37:19 +09:00
Masahiro Yamada
c3ab1e118f mmc: uniphier-sd: sync with Linux
Sync with the driver code and the binding recently merged in Linux.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-09-11 20:37:18 +09:00
Masahiro Yamada
33aae6b5ed ARM: dts: uniphier: sync DT with Linux 4.19-rc1
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-09-11 20:37:16 +09:00
Vikas Manocha
d22336aad9 arm: armv7m: clean up armv7m unified code compilation
unified syntax should be selected by config ARM_ASM_UNIFIED

Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
2018-09-10 21:19:33 -04:00
Vikas Manocha
680223a2da arm: armv7m: remove un-necessary If then instruction
With gas option -mimplicit-it=always, IT block is inserted by the assembler
for thumb2.

Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
2018-09-10 21:19:33 -04:00
Vikas Manocha
17d2887a9e arm: stm32: Remove redundant thumb build selection
All armv7m arch builds are thumb & SYS_THUMB_BUILD is already selected by
CPU_ARMV7M.

Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
2018-09-10 21:19:33 -04:00
Quentin Schulz
d2d908d258 arm: spear: enable GPIO3 and 4 clocks when the GPIO controller driver is built
There are multiple GPIOs that can be used with the same driver depending
on the CONFIG_GPIO_BASE defined in the controller driver.

GPIO3 and 4 require a clock to be enabled so let's enable them when the
driver is built.

Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
2018-09-10 21:19:32 -04:00
Thomas Fitzsimmons
3f20321ad8 board: arm: Add support for Broadcom BCM7260
Add support for loading U-Boot on the Broadcom 7260 SoC.  This port
assumes Broadcom's BOLT bootloader is acting as the second stage
bootloader, and U-Boot is acting as the third stage bootloader, loaded
as an ELF program by BOLT.

Signed-off-by: Thomas Fitzsimmons <fitzsim@fitzsim.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
2018-09-10 21:19:31 -04:00
Adam Ford
93b283d49f ARM: CPU: arm926ejs: Consolidate cache routines to common file
Four different boards had different options for enabling cache
that were virtually all the same.  This consolidates these
common functions into arch/arm/cpu/arm926ejs/cache.c

This also has the positive side-effect of enabling cache on
the Davinci (da850) boards.

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Add mach-at91 to the list of consolidations]
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-09-10 21:19:16 -04:00
Eugen Hristev
51330c72f0 at91: fix devicetree warnings
This commit fixes various devicetree warnings in the at91 devicetrees
like:
arch/arm/dts/sama5d36ek_cmp.dtb: Warning (avoid_unnecessary_addr_size): /gpio_keys: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property

These warnings make buildman report failed builds for most of at91 boards.
Thus, fixing it.

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2018-09-10 20:48:18 -04:00
Eugen Hristev
6e18adaf11 ARM: dts: Makefile: fix build for at91family
For at91family, makefile was building unwanted DTBs
Moved them under specific target configuration.

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2018-09-10 20:48:18 -04:00
Masahiro Yamada
3747bdbb2b arch: types.h: factor out fixed width typedefs to int-ll64.h
All architectures have the same definition for s8/16/32/64
and u8/16/32/64.

Factor out the duplicated code into <asm-generic/int-ll64.h>.

BTW, Linux unified the kernel space definition into int-ll64.h
a few years ago as you see in Linux commit 0c79a8e29b5f
("asm/types.h: Remove include/asm-generic/int-l64.h").

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-09-10 20:48:16 -04:00
Adam Ford
de39dc7162 arm: armv7-a: Compile and tune for armv7-a instead of armv5
arch/arm/Makefile references armv5 for backwards compatibility with
older compilers.  This patch removes those references to armv5,
since by now newer compilers are required which should have armv7
support enabled.

The Makefile also also has a list of options for mtune, but the
entry for CONFIG_CPU_V7A is empty, so this patch tunes the
CPU_V7A architecture to generic-armv7-a.

The following size changed apply to omap3_logic using GCC.

Stock
text data bss dec hex filename
50910 429 67580 118919 1d087 spl/u-boot-spl
540713 22700 327072 890485   d9675 u-boot

Without Armv5
text data bss dec hex filename
50916 429 67580 118925   1d08d spl/u-boot-spl
540719 22700 327064 890483   d9673 u-boot

mtune=generic-armv7-a
text data bss dec hex filename
50932 429 67580 118941   1d09d spl/u-boot-spl
540519 22700 327080 890299   d95bb u-boot

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-09-10 20:48:16 -04:00
Chen-Yu Tsai
792b204798 ARM: Specify aligned address for secure section instead of using attributes
In commit a1274cc94a ("ARM: Page align secure section only when it is
executed in situ"), we used output section attributes (the "ALIGN"
keyword after the colon) to specify the alignment requirements. Using
the constant "COMMONPAGE" there was recently broken in binutils 2.31 [1].

Binutils maintainer Alan Modra suggested the former method would still
work. Since both methods achieve the same result, this patch does just
that. This fixes the "reboot after bootm" issue we've been seeing on
sunxi when booting non-secure.

  [1] https://sourceware.org/bugzilla/show_bug.cgi?id=23571

Suggested-by: Alan Modra <amodra@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Jagan Teki <jagan@openedev.com>
2018-09-07 09:11:42 -04:00
Adam Ford
548c35ff6e ARM: dts: logicpd-torpedo-37xx-devkit-u-boot: Fix MMC Card Detect
When re-syncing the DTS files from the kernel, something caused
the MMC driver to no longer detect the MMC card. Undoing the
CD-invert appears to fix the issue.

Fixes: e6ea2390cd ("ARM: DTS: Resync LogicPD-Torpedo-37xx-devkit
with Linux 4.18-RC4")

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-09-05 16:01:22 -04:00
Tom Rini
b2f90c461e Merge branch 'master' of git://git.denx.de/u-boot-imx 2018-09-04 17:45:53 -04:00
Anson Huang
57b620255e imx: mx7: add system suspend/resume support
This patch adds system suspend/resume support,
when linux kernel enters deep sleep mode, SoC will go
into below mode:

 - CA7 platform goes into STOP mode;
 - SoC goes into DSM mode;
 - DDR goes into self-refresh mode;
 - CPU0/SCU will be powered down.

When wake up event arrives:

 - SoC DSM mdoe exits;
 - CA7 platform exit STOP mode, SCU/CPU0 power up;
 - Invalidate L1 cache;
 - DDR exit self-refresh mode;
 - Do secure monitor mode related initialization;
 - Jump to linux kernel resume entry.

Belwo is the log of 1 iteration of system suspend/resume:

[  338.824862] PM: suspend entry (deep)
[  338.828853] PM: Syncing filesystems ... done.
[  338.834433] Freezing user space processes ... (elapsed 0.001 seconds) done.
[  338.842939] OOM killer disabled.
[  338.846182] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
[  338.869717] PM: suspend devices took 0.010 seconds
[  338.877846] Disabling non-boot CPUs ...
[  338.960301] Retrying again to check for CPU kill
[  338.964953] CPU1 killed.
[  338.968104] Enabling non-boot CPUs ...
[  338.973598] CPU1 is up
[  339.267155] mmc1: queuing unknown CIS tuple 0x80 (2 bytes)
[  339.275833] mmc1: queuing unknown CIS tuple 0x80 (7 bytes)
[  339.284158] mmc1: queuing unknown CIS tuple 0x80 (6 bytes)
[  339.385065] PM: resume devices took 0.400 seconds
[  339.389836] OOM killer enabled.
[  339.392986] Restarting tasks ... done.
[  339.398990] PM: suspend exit

The resume entry function has to initialize stack pointer before calling
C code, otherwise there will be an external abort occur, in additional,
invalidate L1 cache must be done in secure section as well, so this
patch also adds assembly code back and keep it as simple as possible.

Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Tested-by: Stefan Agner <stefan@agner.ch>
2018-09-04 08:47:23 +02:00
Anson Huang
b059837850 imx: mx7: add gpc initialization for low power mode
Add i.MX7D GPC initialization for low power mode
support like system suspend/resume from linux kernel:

 - Pending IOMUXC IRQ to workaround GPC state machine issue;
 - Mask all GPC interrupts for M4/C0/C1;
 - Configure SCU timing;
 - Configure time slot ack;
 - Configure C0/C1 power up/down timing;
 - Configure wakeup source mechanism;
 - Disable DSM/RBC related settings.

Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
2018-09-04 08:47:23 +02:00
Anson Huang
11e52bca84 imx: mx7: psci: improve cpu hotplug flow
This patch improves cpu hotplug, previous cpu_off
implementation is NOT safe, a CPU can NOT power down
itself in runtime, it will cause system bus hang due
to pending transaction. So need to use other online
CPU to kill it when it is ready for killed.

Here use SRC parameter register and a magic number
of ~0 as handshake for killing a offline CPU,
when the online CPU checks the psci_affinity_info,
it will help kill the offline CPU according to
the magic number stored in SRC parameter register.

Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
2018-09-04 08:47:23 +02:00
Martin Kaiser
69f78cf840 watchdog: mx25: use the imx_watchdog driver for mx25
The existing imx_watchdog driver is compatible with mx25 chipsets.
Add a WDOG1_BASE_ADDR define for the base address and enable the driver
in watchdog's Makefile.

To use the driver, a board must define CONFIG_IMX_WATCHDOG and
CONFIG_HW_WATCHDOG.

This fixes an issue when booting an mx25 chip via usb/serial. In this
case, the boot rom will always enable the watchdog. If u-boot is running
in interactive mode and the watchdog is not serviced, the system is
rebooted when the watchdog expires.

Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-09-04 08:47:23 +02:00
Ye Li
25baafc44c dts: imx6ul_evk: Add DTS files for 14x14 EVK and 9x9 EVK boards
Add the board DTS files for 14x14 EVK and 9x9 EVK. They are necessary
for converting to use u-boot DM driver.

Two -u-boot.dtsi are added to modify compatible string of SPI flash
device to "spi-flash".

Signed-off-by: Ye Li <ye.li@nxp.com>
2018-09-04 08:47:23 +02:00
Ye Li
9e1e6f6fe8 dts: imx6ul: Update alias to support DM
Add spi0 alias for qspi for enabling DM SPI.
Change usb alias for usbotg1 and usbotg2 for enabling DM USB

Signed-off-by: Ye Li <ye.li@nxp.com>
2018-09-04 08:47:23 +02:00