Update chipselect handling in davinci_nand.c so that it can
handle 2 GByte chips the same way Linux does: as one device,
even though it has two halves with independent chip selects.
For such chips the "nand info" command reports:
Device 0: 2x nand0, sector size 128 KiB
Switch to use the default chipselect function unless the board
really needs its own. The logic for the Sonata board moves out
of the driver into board-specific code. (Which doesn't affect
current build breakage if its NAND support is enabled...)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Remove CONFIG_SYS_DAVINCI_BROKEN_ECC option. It's not just nasty;
it's also unused by any current boards, and doesn't even match the
main U-Boot distributions from TI (which use soft ECC, or 4-bit ECC
on newer chips that support it).
DaVinci GIT kernels since 2.6.24, and mainline Linux since 2.6.30,
match non-BROKEN code paths for 1-bit HW ECC. The BROKEN code paths
do seem to partially match what MontaVista/TI kernels (4.0/2.6.10,
and 5.0/2.6.18) do ... but only for small pages. Large page support
is really broken (and it's unclear just what software it was trying
to match!), and the ECC layout was making three more bytes available
for use by filesystem (or whatever) code.
Since this option itself seems broken, remove it. Add a comment
about the MV/TI compat issue, and the most straightforward way to
address it (should someone really need to solve it).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Minor cleanup for DaVinci NAND code:
- Use I/O addresses from nand_chip; CONFIG_SYS_NAND_BASE won't
be defined when there are multiple chipselect lines in use
(as with common 2 GByte chips).
- Cleanup handling of EMIF control registers
* Only need one pointer pointing to them
* Remove incorrect and unused struct supersetting them
- Use the standard waitfunc; we don't need a custom version
- Partial legacy cleanup:
* Don't initialize every board like it's a DM6446 EVM
* #ifdef a bit more code for BROKEN_ECC
Sanity checked with small page NAND on dm355 and dm6446 EVMs;
and large page on dm355 EVM (packaged as two devices, not one).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This patch fixes a build problem noticed on Apollon by using
mtd_dev_by_eb() instead of "/" as done in the Linux UBI version.
So this brings the U-Boot UBI version more in sync with the Linux
version again.
Signed-off-by: Stefan Roese <sr@denx.de>
new chips supported:-
MX25L1605D, MX25L3205D, MX25L6405D, MX25L12855E
out of which MX25L6405D and MX25L12855E tested on Kirkwood platforms
Modified the Macronix flash support to use 2 bytes of device id instead of 1
This was required to support MX25L12855E
Signed-off-by: Piyush Shah <spiyush@marvell.com>
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Looks like when I was encoding the sector sizes, I forgot to divide by 8
(due to the stupid marketing driven process that declares all sizes in
useless megabits and not megabytes).
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
NAND module should not modify EMIF registers unrelated to CS2
that is used for NAND, i.e. do not modify EWAIT config register
or registers for other Chip Selects.
Without this patch, EMIF configurations made in board_init()
will be invalidated.
Signed-off-by: Thomas Lange <thomas@corelatus.se>
This patch adds NAND Flash Controller driver for MPC5121 revision 2.
All device features, except hardware ECC and power management, are
supported.
This NFC driver replaces the one orignally posted by John Rigby:
"[PATCH] Freescale NFC NAND driver"
It's a port of the Linux driver version posted by Piotr Ziecik a few
weeks ago. Using this driver has the following advantages (from my
point of view):
- Compatibility with the Linux NAND driver (e.g. ECC usage)
- Better code quality in general
- Resulting U-Boot image is a bit smaller (approx. 3k)
- Better to sync with newer Linux driver versions
The only disadvantage I can see, is that HW-ECC is not supported right
now. But this could be added later (e.g. port from Linux driver after
it's supported there). Using HW-ECC on the MCP5121 NFC has a general
problem because of the ECC usage in the spare area. This collides with
JFFS2 for example.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Piotr Ziecik <kosmo@semihalf.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: John Rigby <jcrigby@gmail.com>
Cc: Scott Wood <scottwood@freescale.com>
UBI is quite memory greedy and requires at least approx. 512k of malloc
area. This patch adds a compile-time check, so that boards will not
build with less memory reserved for this area (CONFIG_SYS_MALLOC_LEN).
Signed-off-by: Stefan Roese <sr@denx.de>
Added macronix SF driver for MTD framework
MX25L12805D is supported and tested
TBD: sector erase implementation, other deivces support
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This new define enables mtdcore.c compilation and with this we can
select the MTD device infrastructure needed for the reworked mtdparts
command.
We now have the 2 MTD infrastructure defines, CONFIG_MTD_DEVICE and
CONFIG_MTD_PARTITIONS. CONFIG_MTD_DEVICE is needed (as explained above)
for the "mtdparts" command and CONFIG_MTD_PARTITIONS is needed for UBI.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
This patch brings the U-Boot MTD infrastructure in sync with the current
Linux MTD version (2.6.30-rc3). Biggest change is the 64bit device size
support and a resync of the mtdpart.c file which has seen multiple fixes
meanwhile.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Kyungmin Park <kmpark@infradead.org>
This patch adds concatenation support to the U-Boot MTD infrastructure.
By enabling CONFIG_MTD_CONCAT this MTD CFI wrapper will concatenate
all found NOR devices into one single MTD device. This can be used by
e.g by UBI to access a partition that spans over multiple NOR chips.
Signed-off-by: Stefan Roese <sr@denx.de>
Several boards used different ways to specify the size of the
protected area when enabling flash write protection for the sectors
holding the environment variables: some used CONFIG_ENV_SIZE and
CONFIG_ENV_SIZE_REDUND, some used CONFIG_ENV_SECT_SIZE, and some even
a mix of both for the "normal" and the "redundant" areas.
Normally, this makes no difference at all. However, things are
different when you have to deal with boards that can come with
different types of flash chips, which may have different sector
sizes.
Here we may have to chose CONFIG_ENV_SECT_SIZE such that it fits the
biggest sector size, which may include several sectors on boards using
the smaller sector flash types. In such a case, using CONFIG_ENV_SIZE
or CONFIG_ENV_SIZE_REDUND to enable the protection may lead to the
case that only the first of these sectors get protected, while the
following ones aren't.
This is no real problem, but it can be confusing for the user -
especially on boards that use CONFIG_ENV_SECT_SIZE to protect the
"normal" areas, while using CONFIG_ENV_SIZE_REDUND for the
"redundant" area.
To avoid such inconsistencies, I changed all sucn boards that I found
to consistently use CONFIG_ENV_SECT_SIZE for protection. This should
not cause any functional changes to the code.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Paul Ruhland
Cc: Pantelis Antoniou <panto@intracom.gr>
Cc: Stefan Roese <sr@denx.de>
Cc: Gary Jennejohn <garyj@denx.de>
Cc: Dave Ellis <DGE@sixnetio.com>
Acked-by: Stefan Roese <sr@denx.de>
This patch now enabled this cfi-mtd wrapper to correctly detect and
erase the last sector in an NOR FLASH device.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch enables Smart Media (SMC) ECC byte ordering which is used
on the PPC4xx NAND FLASH controller (NDFC). Without this patch we have
incompatible ECC byte ordering to the Linux kernel NDFC driver.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Scott Wood <scottwood@freescale.com>
With this patch non-uniform NOR FLASH chips (chips with multiple erase
regions) can be exported via the cfi-mtd layer and therefor used by UBI.
We select the largest sector size as erasesize. The cfi driver will make
sure that the smaller sectors are handled correctly.
Signed-off-by: Stefan Roese <sr@denx.de>
With this patch the NAND and OneNAND devices are registered in the MTD
subsystem and can then be referenced by the mtdcore code (e.g.
get_mtd_device_nm()). This is needed for the new "ubi part" command
syntax without the flash type parameter (nor|nand|onenand).
Signed-off-by: Stefan Roese <sr@denx.de>
This patch removes this compilation warning when CONFIG_MTD_PARTITIONS is
defined:
nand_base.c: In function 'nand_release':
nand_base.c:2922: warning: implicit declaration of function 'del_mtd_partitions'
Signed-off-by: Stefan Roese <sr@denx.de>
Fix dependency goofage: it should certainly be possible to have the
partition support without bringing in UBI commands.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Stefan Roese <sr@denx.de>
We need to make sure the data written to the nand flash controller makes
it there before we start polling its status register. Otherwise, we may
get stale data and return before the controller is actually ready.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Scott Wood <scottwood@freescale.com>
On platforms with multiple NOR chips, currently only the first one
can be selected using the "ubi part" command. This patch fixes this
problem by using different names for the NOR "mtd devices".
It also changes the name of the NOR MTD device from "cfi-mtd" to
"norX" (X indexing the device numer) to better match the mtdparts
defaults.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Andreas Huber <andreas.huber@keymile.com>
The AT91RM9200-EK Evaluation Board supports the AT91RM9200
ARM9-based 32-bit RISC microcontroller and enables real-time code development
and evaluation.
Here is the chip page on Atmel website:
http://www.atmel.com/dyn/products/tools_card.asp?tool_id=3507
with
- NOR (cfi driver)
- DataFlash
- USB OHCI
- Net
- I2C (hard)
Signed-off-by: Ulf Samuelsson <ulf@atmel.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Legacy NAND is marked for feature removal after April 2009 (i.e. this
upcoming release). There are still several boards that reference it
(though many do so only for disk-on-chip support which has been silently
disabled for a while now). These boards will now fail to build
with #error, though the code is still there if the user removes #error.
The plan is to remove the code outright in the next release, along with
any board code that refers to it (such as board/esd/common/auto_update.c).
Also, remove the legacy NAND API description from README.nand.
Signed-off-by: Scott Wood <scottwood@freescale.com>
I can't find anywhere in the datasheet that says the status register needs
3 dummy bytes sent to it before being able to read back the first real
result. Tests on a Blackfin board show that after writing the opcode, the
status register starts coming back immediately. So only write out the
read status register opcode before polling the result.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Jason McMullan <mcmullan@netapp.com>
CC: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Since timeouts are only hit when there is a problem in the system, we
don't want to prematurely timeout on a functioning setup. Thus having
low timeouts (in milliseconds) doesn't gain us anything in the production
case, but rather increases likely hood of causing problems where none
otherwise exist.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Some SPI flash drivers like to have extended id information available
(like the spansion flash), so rather than making it re-issue the ID cmd
to get at the last 2 bytes, have the common code read 5 bytes rather than
just 3. This also matches the Linux behavior where it always reads 5 id
bytes from all flashes.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
CC: Mingkai Hu <Mingkai.hu@freescale.com>
The common SPI flash code reads the idcode and passes it down to the SPI
flash driver, so there is no need to read it again ourselves.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
CC: Jason McMullan <mcmullan@netapp.com>
CC: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Add MTD SPI Flash support for S25FL008A, S25FL016A,
S25FL032A, S25FL064A, S25FL128P.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The NAND flash on the TQM8548_BE modules requires a short delay after
running the UPM pattern like the MPC8360ERDK board does. The TQM8548_BE
requires a further short delay after writing out a buffer. Normally the
R/B pin should be checked, but it's not connected on the TQM8548_BE.
The corresponding Linux FSL UPM driver uses similar delay points at the
same locations. To manage these extra delays in a more general way, I
introduced the "wait_flags" field allowing the board-specific driver to
specify various types of extra delay.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
For the NAND chips on the TQM8548 modules, a special chip-select logic is
used. It uses dedicated address lines to be set via UPM machine address
register (mar). This patch adds such support to the FSL-UPM driver.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This patch adds support for multi-chip NAND devices to the FSL-UPM
driver. The "dev_ready" callback of the "struct fsl_upm_nand" is now
called with the argument "chip_nr" to allow testing the proper chip
select line. The NAND support of the MPC8360ERDK is updated as well.
No other boards are currently using the FSL UPM driver.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This patch adds support for NAND_MAX_CHIPS to the MTD NAND layer.
Multi-chips devices are displayed as shown:
Device 0: 2x NAND 512MiB 3,3V 8-bit, sector size 128 KiB
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
On the pcm030 the environment is located in the onboard EEPROM. But we want
to handle flash sector protection in a safe manner. So we must read the
unlock environment variable from EEPROM instead from flash.
This patch is required as long the evironment is saved into the EEPROM.
Stefan: Additional change as suggested by Wolfgang, use bigger char array
(instead of 4).
Signed-off-by: Eric Schumann <E.Schumann@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Follow up to the flash_fixup_stm to fix geometry reversal
on STMicro M29W320ET flash chip. The M29W320DT has 4 erase region.
Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This driver implements the ECC algorithm described in
the CPU data sheet and uses the OOB layout chosen in
already-released development systems (shipped with a custom-made
u-boot 1.3.1).
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stnwireless.com>
If on your board is more than one flash, you must know
the size of every single flash, for example, for updating
the DTS before booting Linux. So make this function
flash_get_info() extern, and you can have all info
about your flashes.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Without the timeout present an infinite loop can occur if the
NAND device is broken or not present.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Commit cfa460adfd removed support
for disabling the "No NAND device found!!!" warning when
CONFIG_SYS_NAND_QUIET_TEST was defined. This re-adds support
for silencing the warning.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Dear Wolfgang,
You are right, the patch was ugly.
The new one seems to be better.
Signed-off-by: Valeriy Glushkov <gvv@lstec.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Patch "flash/cfi_flash: Use virtual sector start address, not phys"
introduced a small typo and compilation warning for systems with CFI
legacy support (e.g. hcu4). This patch fixes it.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch removes the double defined manufacturer defines from
jedec_flash.c. Since the common defines in flash.h are 32bit
we now need the (16) cast. This patch also removes the compilation
warning (e.g. seen on hcu5):
./MAKEALL hcu5
Configuring for hcu5 board...
jedec_flash.c:219: warning: large integer implicitly truncated to unsigned type
Signed-off-by: Stefan Roese <sr@denx.de>
Patch "flash/cfi_flash: Use virtual sector start address, not phys"
introduced a small compilation warning. This patch fixes it.
Signed-off-by: Stefan Roese <sr@denx.de>
include/flash.h was commented to say that the address in
flash_info->start was a physical address. However, from u-boot's
point of view, and looking at most flash code, it makes more
sense for this to be a virtual address. So I corrected the
comment to indicate that this was a virtual address.
The only flash driver that was actually treating the address
as physical was the mtd/cfi_flash driver. However, this code
was using it inconsistently as it actually directly dereferenced
the "start" element, while it used map_physmem to get a
virtual address in other places. I changed this driver so
that the code which initializes the info->start field calls
map_physmem to get a virtual address, eliminating the need for
further map_physmem calls. The code is now consistent.
The *only* place a physical address should be used is when defining the
flash banks list that is used to initialize the flash_info struct,
usually found in the board config file.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Stefan Roese <sr@denx.de>
Added flash_fixup_stm to fix geometry reversal on STMicro M29W320ET flash chip.
Modeled after flash_fixup_amd, this patch handles the geometry reversal
or erase sectors that exist for ST Micro (now Numonyx) M29W320ET flash.
Since I cannot test all STM's chips, the detection is implemented as
narrow as possible for now.
Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The function find_sector() doesn't need to be called twice in
the case of AMD command set.
Tested on TQM5200S-BD with Samsung K8P2815UQB.
Signed-off-by: Jens Gehrlein <sew_s@tqs.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Higher spi flash layers expect to be given back a pointer that was
malloced so that it can free the result, but the lower layers return
a pointer that is in the middle of the malloced memory. Reorder the
members of the lower spi structures so that things work out.
Signed-off-by: Brad Bozarth <bflinux@yumbrad.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This patch renames NAND_MAX_CHIPS to CONFIG_SYS_NAND_MAX_CHIPS and
changes the default from 8 to 1 for the legacy and the new MTD
NAND layer. This allows to remove all NAND_MAX_CHIPS definitions
in the board config files because none of the boards use multi
chip support (NAND_MAX_CHIPS > 1) so far. The bamboo and the DU440
define
#define NAND_MAX_CHIPS CONFIG_SYS_MAX_NAND_DEVICE
but that's bogus and did not work anyhow.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Enable nand lock, unlock and status of lock feature.
Not every device and platform requires this, hence,
it is under define for CONFIG_CMD_NAND_LOCK_UNLOCK
Nand unlock and status operate on block boundary instead
of page boundary. Details in:
http://www.micron.com/products/partdetail?part=MT29C2G24MAKLAJG-6%20IT
Intial solution provided by Vikram Pandita <vikram.pandita@ti.com>
Includes preliminary suggestions from Scott Wood
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Rather than putting the function prototype for board_nand_init() in the one
place where it gets called, put it into nand.h so that every place that also
defines it gets the prototype. Otherwise, errors can go silently unnoticed
such as using the wrong return value (void rather than int) when defining
the function.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Scott Wood <scottwood@freescale.com>
- Add subpage write support
- Add onenand_oob_64/32 ecclayout
This has been missing and without it UBI has some incompatibilies issues
with the current (>= 2.6.27) Linux kernel version. vid_hdr_offset is
placed differently (2048 instead of 512) without this fix.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The version (ver_id) was not stored in the onenand_chip structure and
because of this the continuous locking scheme could be enabled on some
chips.
Signed-off-by: Stefan Roese <sr@denx.de>
The current code that determines which bank/chipselect is used for a
given NAND instance only worked for 32-bit addresses and assumed
a 1:1 mapping. This breaks in 36-bit physical configs.
The proper way to handle this is to use the virt_to_phys() and
BR_PHYS_ADDR() routinues to match the 34-bit lbc bus address
with the the virtual address the NAND code uses.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Scott Wood <scottwood@freescale.com>
Otherwise, recursion can occur if scan_bbt does not find a bad block
table, and tries to write one, and the attempt to erase the BBT area
causes a bad block check.
Signed-off-by: Scott Wood <scottwood@freescale.com>
The stmicro_wait_ready() func tries to show the actual opcode that was sent
to the device, but instead it displays the array pointer. Fix it to pull
out the opcode from the start of the array.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
With this patch now, the user can call "ubi part" multiple times to
re-connect the UBI device to another MTD partition.
Signed-off-by: Stefan Roese <sr@denx.de>
Don't use LIST_HEAD() but initialize the struct via INIT_LIST_HEAD() upon
first call of add_mtd_partitions(). Otherwise this won't work on platforms
where the relocation is broken (like MIPS or PPC).
Signed-off-by: Stefan Roese <sr@denx.de>
This patch fix the problem that only the [NB_DATAFLASH_AREA - 1] dataflash
partition can be defined to use the area to the end of dataflash size.
Now it is possible to have only one dataflash partition from 0 to the end
of of dataflash size.
Signed-off-by: Ilko Iliev <iliev@ronetix.at>
This caused the operation to be needlessly repeated if there were
no bad blocks and no errors.
Signed-off-by: Valeriy Glushkov <gvv@lstec.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Remove a printf() from add_mtd_device(), which produces spurious output.
Signed-off-by: Piotr Ziecik <kosmo@semihalf.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Add cfi-mtd driver, which exports CFI flash to MTD layer.
This allows CFI flash devices to be used from MTD layer.
Building of the new driver is controlled by CONFIG_FLASH_CFI_MTD
option. Initialization is done by calling cfi_mtd_init() from
flash_init().
Signed-off-by: Piotr Ziecik <kosmo@semihalf.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Add interface for flash verbosity control. It allows
to disable output from low-level flash API. It is useful
when calling these low-level functions from context other
than flash commands (for example the MTD/CFI interface
implmentation).
Signed-off-by: Piotr Ziecik <kosmo@semihalf.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Export flash_sector_size() function from drivers/mtd/cfi_flash.c,
so that it can be used in the upcoming cfi-mtd driver.
Signed-off-by: Piotr Ziecik <kosmo@semihalf.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch defines all flash access functions as weak so that
they can be overridden by board specific versions.
This will be used by the upcoming VCTH board support where the NOR
FLASH unfortunately can't be accessed memory-mapped. Special
accessor functions are needed here.
To enable this weak functions you need to define
CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS in your board config header.
Otherwise the "old" default functions will be used resulting
in smaller code.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This patch adds basic UBI (Unsorted Block Image) support to U-Boot.
It's based on the Linux UBI version and basically has a "OS"
translation wrapper that defines most Linux specific calls
(spin_lock() etc.) into no-ops. Some source code parts have been
uncommented by "#ifdef UBI_LINUX". This makes it easier to compare
this version with the Linux version and simplifies future UBI
ports/bug-fixes from the Linux version.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds basic UBI (Unsorted Block Image) support to U-Boot.
It's based on the Linux UBI version and basically has a "OS"
translation wrapper that defines most Linux specific calls
(spin_lock() etc.) into no-ops. Some source code parts have been
uncommented by "#ifdef UBI_LINUX". This makes it easier to compare
this version with the Linux version and simplifies future UBI
ports/bug-fixes from the Linux version.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds basic UBI (Unsorted Block Image) support to U-Boot.
It's based on the Linux UBI version and basically has a "OS"
translation wrapper that defines most Linux specific calls
(spin_lock() etc.) into no-ops. Some source code parts have been
uncommented by "#ifdef UBI_LINUX". This makes it easier to compare
this version with the Linux version and simplifies future UBI
ports/bug-fixes from the Linux version.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds basic UBI (Unsorted Block Image) support to U-Boot.
It's based on the Linux UBI version and basically has a "OS"
translation wrapper that defines most Linux specific calls
(spin_lock() etc.) into no-ops. Some source code parts have been
uncommented by "#ifdef UBI_LINUX". This makes it easier to compare
this version with the Linux version and simplifies future UBI
ports/bug-fixes from the Linux version.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds basic UBI (Unsorted Block Image) support to U-Boot.
It's based on the Linux UBI version and basically has a "OS"
translation wrapper that defines most Linux specific calls
(spin_lock() etc.) into no-ops. Some source code parts have been
uncommented by "#ifdef UBI_LINUX". This makes it easier to compare
this version with the Linux version and simplifies future UBI
ports/bug-fixes from the Linux version.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Stefan Roese <sr@denx.de>
