OrangePi Zero2 is SBC based on Allwinner H616 with 1 GiB of RAM, SD card
support, gigabit ethernet, micro HDMI, WIFI, Bluetooth and 1 USB 2.0
port. It also has two GPIO headers which allows further peripherals to
be used.
The devicetree file is taken from v3 of the OrangePi Zero2 Linux
submission [1], which it's not yet merged.
[1] http://lists.infradead.org/pipermail/linux-arm-kernel/2021-January/632084.html
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This commit introduces H616 DTSI file and dt-bindings headers needed for
device tree files.
Files are taken from v3 Linux H616 support submission[1], as the
H616 .dtsi file is not merged upstream yet.
[1] http://lists.infradead.org/pipermail/linux-arm-kernel/2021-January/632082.html
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
H616 uses different address for reset. Add it.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
H616 is very similar to H6 so most of the infrastructure can be reused.
However, two big differences are that it doesn't have functional SRAM A2
which is usually used for TF-A and it doesn't have ARISC co-processor.
It also needs bigger SPL size - 48 KiB.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Allwinner H616 supports many types of DRAM. Most notably it supports
LPDDR4. However, all commercially available boards at this time use
only DDR3, so this commit adds only DDR3 support.
Controller and MBUS are very similar to H6 but PHY is completely
unknown.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Acked-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This port is needed for communication with PMIC. SPL uses it to set DRAM
voltage on H616 boards.
Reviewed-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This port is used for debug terminal on all known H616 boards.
Reviewed-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
H616 has mostly the same clocks as H6 with some small differences. Just
reuse H6 clocks for H616 and handle differences with macros.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
H616 supports and needs bigger SPL than 32 KiB, mostly due to big DRAM
driver and need for PMIC configuration, which pulls several drivers which
are not needed otherwise.
spl_mmc_get_uboot_raw_sector() will now compare pre-configured size with
that, reported in SPL header. If size in header is bigger, it will use
that value instead.
In the process of function rework, also add missing function argument.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Samuel Holland <samuel@sholland.org>
I2C support, especially R_I2C port, will be needed in future. Upcoming
support for H616 will need R_I2C to adjust DRAM voltage.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
There was no need to have prcm definitions for H6 and similar SoCs till
now. However, support R_I2C will be needed soon in SPL.
Move old definitions to prcm_sun6i.h and add new ones in prcm_sun50i.h.
One of those files will be selected in common prcm.h based on defined
macros.
This commit doesn't do any functional change.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
It turns out that several SoCs share same mmc configuration as H6. In
order to lower ifdef clutter replace H6 specific macro with common one.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
It turns out that there are at least 2 other SoCs which have basically
the same memory map, similar clocks and other features as H6. It's very
likely that we'll see more such SoCs in the future. In order to ease
porting to new SoCs and lower ifdef clutter, introduce common symbol for
them.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This PMIC can be found on H616 boards and it's very similar to AXP805
and AXP806.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
dts file is taken from Linux 5.11-rc1 tag.
The Bluetooth controller of this device ships with a default address,
use the new CONFIG_FIXUP_BDADDR option to fix it up.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
[Updated OrangePi 3 DT, rebase and config update]
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This commit adds support for Tanix TX6 TV box, based on H6. It's low end
H6 board, with 3 GiB of RAM, eMMC, fast ethernet, USB, IR and other
peripherals.
DT file is taken from Linux 5.11-rc1 release.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Updated H6 DT files are based on Linux 5.11-rc1 release.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmAOkP8cHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyKedCACiDHgP71VKSOiYnEU4
vHD/ANmfMXqnsL71PpSdagnBRAl4vpm46CnD+Mq7RtchxGDNufX6tWJSI04Ci0bC
mfmIfVEjePOnuUayylJ55OlrtJVpBqJFPqxM6MFcIF7nRja1r5thV1jTLNu+b4sm
gg2sk1mC/531Lxbk8S7x+diPymNRArEm3IEw+xEqUhsNVQCKjOEcxi/BWIB2prR3
NxRSGdW3j4CKdBqt7uOL1bqApeQQ9m0/gm1tE3hMXUo09I7uXmb7U52aKb5cV8L+
8ZOlbav6yaPACe3p9npp4K0ByXMmYHjeo1NZW4cvAoKfzragdu0Cv7f0ssVCgrlR
p1e3
=xS6A
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2021.04-b' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
Second set of u-boot-atmel features for 2021.04 cycle
This feature set includes macb updates for all interfaces and new
sama7g5 variant support; micrel ksz9031 DLL support; a new board from
Giant based on Adafruit feather form factor which contains a SAMA5D27
SoC; several fixes regarding the NAND flash PMECC block; and pincontrol
drive strength support for pio4 controller.
Beacon EmbeddedWorks is releasing a devkit based on the i.MX8M
Nano SoC consisting of baseboard + SOM.
The kit is based on the same design as the Beacon dev kit with
the i.MX8M Mini.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The CSPI/ECSPI register bits do not differ between newer SoCs, instead
of having multiple copies of the same thing for each iMX SoC, define
the bits in the driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Stefano Babic <sbabic@denx.de>
In order to support the QSPI chip on the SOM, the Flexspi bus
needs to be configured to talk with the SPI chip.
Resync the som device tree with 5.11-rc4
Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
This patch converts the dart6ul ethernet support to DM_ETH and cleans
up the legacy ethernet code. The clean up, more specifically:
* moves the fec2 node and pin definition to the carrier board DTS
since the phy associated with it is on the carrier board and not on
the SoM;
* add the reset pin associated to each phy;
* separate the ethernet, mdio and reset pins of each fec so that they
are easier to reference;
* add clock properties to the phy nodes since they are connected to the
50Mhz ENET[12]_TX_CLK clock of the SoC;
* remove CONFIG_BOARD_EARLY_INIT_F since the function is now empty.
Signed-off-by: Marc Ferland <ferlandm@amotus.ca>
Modify the GPT common platform driver for mx7 which only use 24Mhz
OSC as clock source.
Note: at default, the mx7d will use system counter as timer. The GPT
is disabled.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When boot type could not be detected from rom sw info,
read sbmr1 to detect, here we only use it to detect FLEXSPI
boot, because ROM not update it in rom sw info.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Since we remove SATA device before boot OS, when AHCI is enabled, update
the codes to remove AHCI device.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
iMX8MP has shifted market segment fuse one bit from 0x440 [7:6] to [6:5],
correct it in imx common codes.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add NAND boot support for i.MX8MP by adding i.MX8MP in nandbcb support
list, reading boot_search_count from fuse.
i.MX8MN NAND boot is same as i.MX8MP, fix some issues as well.
Signed-off-by: Han Xu <han.xu@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Fix Coverity Issue 9006656. In nandbcb_set_boot_config, an integer overflow
occurs, with the result converted to a wider integer type.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Fix Coverity Issue 9006658. In fill_dbbt_data, an integer overflow occurs,
with the result converted to a wider integer type
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Fix Coverity Issue 9006657. In read_fcb, leak of memory to system
resource "fcb_raw_page". Adjust the sequence to check the mtd bad
block prior than allocation of "fcb_raw_page", also check the NULL
return of allocation.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Fix Coverity Issue 9006655. In write_fcb, leak of memory to resource
"fcb_raw_page". Since we have initialized the "ret" to 0, should return
the value of ret.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Fix Coverity Issue 9006654. In write_fcb, use of an uninitialized
variable "ret".
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
use CONFIG_TARGET_IMX8MN_DDR4_EVK for DDR4 EVK board, we will use
CONFIG_TARGET_IMX8MN_EVK for LPDDR4 EVK board.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The dm root node is needed early in the spl to allow the timer to be
used. This change calls spl_early_init to initialize the dm root node.
Signed-off-by: Greg Gallagher <greg@embeddedgreg.com>
Giant board is a tiny SBC based on the Adafruit Feather form factor,
created by groboards it contains a SAMA5D2 processor (SAMA5D27),
128 MB of RAM and a microSD card for storage.
Signed-off-by: Greg Gallagher <greg@embeddedgreg.com>
Because ATMEL_BASE_ROM is defined to 0x100000, it already points
to the begin of the index table for 512 byte sectors correction.
Thus its offset must be zero and the index of the table for 1024
byte sectors must start at offset 0x8000.
Signed-off-by: Kai Stuhlemmer (ebee Engineering) <kai.stuhlemmer@ebee.de>
[ta: update commit message]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Offsets are described in the datasheet at section:
"11.4.4.2 NAND Flash Boot: PMECC Error Detection and Correction".
For testing I "injected" bit flips into u-boot NAND memory area,
and then read back. PMECC could not correct the errors. With the
offsets updated everything is fine.
Fixes: 3225f34e5c ("ARM: atmel: add sama5d3xek support")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
This adds support for the NanoPi R2S from FriendlyArm.
Rockchip RK3328 SoC
1GB DDR4 RAM
Gigabit Ethernet (WAN)
Gigabit Ethernet (USB3) (LAN)
USB 2.0 Host Port
MicroSD slot
Reset button
WAN - LAN - SYS LED
Signed-off-by: David Bauer <mail@david-bauer.net>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
The rng is embedded in the SoC so enable it in the device tree
universally, the use of it can be controlled by enabling/disabling
at the device config level.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
SPI flash on this machine is located on bus 1, default to using bus 1
for SPI flash and stop aliasing it to bus 0. Formerly the alias spi1
pointed to &spi5, use an alias spi5 for this instead.
Signed-off-by: Hugh Cole-Baker <sigmaris@gmail.com>
Suggested-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
SPI flash on this board is located on bus 1, default to using bus 1 for
SPI flash on both rk3399-roc-pc and -mezzanine, and stop aliasing it to
bus 0.
Signed-off-by: Hugh Cole-Baker <sigmaris@gmail.com>
Suggested-by: Simon Glass <sjg@chromium.org>
Fixes: c4cea2bb ("rockchip: Enable building a SPI ROM image on bob")
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
Add low level platform initialization for the AST2600 SoC.
The 2-stage booting with U-Boot SPL are leveraged to support
different booting mode.
However, currently the patch supports only the booting from
memory-mapped SPI flash.
Signed-off-by: Chia-Wei, Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
AST2600 is the 7th generation of Aspeed SoC designated for
Interated Remote Management Processor.
AST2600 has significant performance improvement by integrating
1.2GHz dual-core ARM Cortex A7 (r0p5) CPU with FPU. Most of the
controllers are also improved with more features and better
performance than preceding AST24xx/AST25xx.
Signed-off-by: Chia-Wei, Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
AST2600 has 8 watchdog timers including 8 sets of
32-bit decrement counters, based on 1MHz clock.
A 64-bit reset mask is also supported to specify
which controllers should be reset by the WDT reset.
Signed-off-by: Chia-Wei, Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
AST2600 supports DDR4 SDRAM with maximum speed DDR4-1600.
The DDR4 DRAM types including 128MbX16 (2Gb), 256MbX16 (4Gb),
512MbX16 (8Gb), 1GbX16 (16Gb), and 1GbX8 TwinDie (16Gb) are supported.
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Signed-off-by: Chia-Wei, Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
This patch adds the clock control driver
for the AST2600 SoC.
Signed-off-by: Ryan Chen <ryan_chen@aspeedtech.com>
Signed-off-by: Chia-Wei, Wang <chiawei_wang@aspeedtech.com>
Set environment for Nand flash (U-boot 2020.04):
- add nand flash in the device tree
- add new default configuration file for G3 using parallel Nand
- set nand parameters in presidio_asic.h
Signed-off-by: Kate Liu <kate.liu@cortina-access.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
CC: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The pci_mmc.c driver can generate ACPI info and therefore includes
asm/acpi_table.h by proxy. This file does not exist for the ARM
architecture and thus code compilation failed when using this
driver on ARM.
Signed-off-by: Harm Berntsen <harm.berntsen@nedap.com>
CC: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
As no gpio.h is defined for this architecture, to avoid
compilation failure, do not include <asm/arch/gpio.h> for
QEMU.
Signed-off-by: Harm Berntsen <harm.berntsen@nedap.com>
Remove the leading "0x" from rpc node to fix the below dtc warning:
Warning (simple_bus_reg): Node /soc/rpc@0xee200000 simple-bus unit
address format error, expected "ee200000"
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Add a return value to noncached_init and use it directly in the
post-relocation init sequence, rather than using a wrapper stub.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add binman node to device tree to generate the FIT image for u-boot
(u-boot.itb) and OS kernel (kernel.itb).
u-boot.itb contains arm trusted firmware (ATF), u-boot proper and
u-boot device tree for ATF u-boot flow.
kernel.itb contains Linux Image and Linux device tree.
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
SPL already setup the Clock Manager with the handoff data
from OCRAM. When the Clock Manager's driver get probed again
in SSBL, it shall skip the handoff data access in OCRAM.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
In non-secure mode (EL2), Reset Manager driver calls the
SMC/PSCI service provided by ATF to enable/disable the
SOCFPGA bridges.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
invoke_smc() allow U-Boot proper running in non-secure mode (EL2)
to invoke SMC call to ATF's PSCI runtime services such as
System Manager's registers access, 2nd phase bitstream FPGA
reconfiguration, Remote System Update (RSU) and etc.
smc_send_mailbox() is a send mailbox command helper function which invokes
the ATF's PSCI runtime service (function ID: INTEL_SIP_SMC_MBOX_SEND_CMD)
to send mailbox messages to Secure Device Manager (SDM).
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Standard PSCI function "CPU_ON" provided by ATF is now used
by Linux kernel to bring up the secondary CPUs to enable SMP
booting in Linux on SoC 64bits platform.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Override 'lowlevel_init' to make sure secondary CPUs trapped
in ATF instead of SPL. After ATF is initialized, it will signal
the secondary CPUs to jump from SPL to ATF waiting to be 'activated'
by Linux OS via PSCI call.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Add board_fit_config_name_match() for matching board name with
device tree files in FIT image. This will ensure correct DTB
file is loaded for different board type. Currently, we are not
supporting multiple device tree files in FIT image therefore this
function basically do nothing for now.
Users are allowed to override this 'weak' function in their
specific board implementation.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
- Update MAINTAINERS emails for STI and STM32
- Activate OF_LIVE for ST stm32mp15 boards
- Switch to MCO2 for PHY 50 MHz clock for DHCOM boards
- Correction in stm32prog command on uart: always flush DFU on start command
- Update USB-C power detection algorithm on DK boards
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAl/+yLkACgkQ4rK92eCq
k3X/Fgf/d/11WyQrVzvpr+nN+4Wl7J+ASmoUz0yKa6ri+lbvhLgh+JXbCRKgRPWu
vNnI07pSoX/QeaMpGBU8Ztg/Onb9/pvffz4WMk1411GoyCpDFuuK3cVSIoqkPfu+
XmgSX0u4BXtve1+ZdWfVBWXawUSEDMmGR3tmz1708c/s/oYpnVeRDcqiqzJ94cWE
yt+SpMPVqMUVQ/rAGkE8ToSMxX7FusEa7SvCg4U2ikoRWs3kPpr/73+tRWlmgGxL
sW8SXSKiOmFyheSBx3d2B9n00kDYTTrQmbW9hlMilZmji7CwZYxgTCMdX0x4DeFP
RDajT2Yju1JmeM+Z8+Ke2tupzvy6QA==
=oK8C
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20210113' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- Enable logging features for stm32mp15 boards
- Update MAINTAINERS emails for STI and STM32
- Activate OF_LIVE for ST stm32mp15 boards
- Switch to MCO2 for PHY 50 MHz clock for DHCOM boards
- Correction in stm32prog command on uart: always flush DFU on start command
- Update USB-C power detection algorithm on DK boards
A previous series already update STMicroelectronics emails maintainers
but some files have been omitted (Makefile, .dts, .dtsi and .rst files).
Update Patrick and my email address with the one dedicated to upstream
activities.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Remove the test on data->dfu_seq, because dfu_seq=0 not only when
the DFU is not started (mask with 0xffff). This flush is mandatory
as the final treatment, common with USB, is done in DFU callback.
This patch avoids issue if the received length is a multiple of
the DFU packet.
For example if size of bootfs partition is egual to 0x4000000,
data->dfu_seq=0 at the end of the partition, the flush it not
requested and the phase is not increased in the callback.
U-Boot continue to request the bootfs in the next GetPhase command.
Fixes: 468f0508b5 ("stm32mp: stm32prog: add serial link support")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The LAN8710i PHY currently uses 50 MHz clock direct from PLL4P.
To permit PLL4P to run at faster frequency, use MCO2 as a divider.
The PLL4P runs at 100 MHz, supplies MCO2 which divides it by 2 to
50MHz, and supplies the PHY with 50 MHz via pin PG2. The feedback
clock are fed back in via pin PA1.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Change-Id: Ia9bf7119785d49b633a3ae761c3dc4a30b92628a
Define LOG_CATEGORY, change pr_debug to dev_dbg and remove "bsec:"
header as it is managed by log macro (dev->name is displayed)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Change debug and pr_ macro to log macro and define LOG_CATEGORY.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Remove board_mmc_init function.
It will be probed with driver-model.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
- DM support for OMAP PWM backlight
- USB host mode support for AM654
- Minor SPI fixes
- Add support k2g ice board with 1GHz silicon
- Fix GTC programming for K3 devices
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAl/8S/0cHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyKFkB/9NBJq/+sgHZXRaMlAu
ULNwOPoNsQxHQGwF88B1lC+H8LJjM+2gJ8MfJdWvHNlcSdtJjbWk0aQL+5LKSlyz
G7l3BZ+AIYMOeTXay5mNUKnekXIr7c8tLoX8FH/Ih+bHFPt57qL0bbfznV66UCOp
/o/yM8daPa9Kx1vPEpT2dC9bYXLXeQv6R+RMxwoc4Bk+R3OK7zoZ3Wdx0q9HvBwj
iWHM49X2fBqqi5RS+ZI37AUzi8iysD3fOq0kWTJcCNaci8i8RZdzSyoaDuXhA63I
EZJ7v9fUkW/bwTONVE9n2BX4xF9X/6R7P46l9dQISXAxsOBwsNRQPt8Ro7mCoc4K
392o
=LIK7
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2021.04-a' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
First set of u-boot-atmel features for 2021.04 cycle
This feature set includes the new board SAMA7G5 EK, the new evaluation
kit for Microchip AT91 SAMA7G5 SoC . The current board support includes
two configurations for booting from eMMC (SDMMC0), SD-Card (SDMMC1), and
support for two Ethernet interfaces.
Enabling the domain clock is performed by the sysc interconnect target
module driver during the video device probing.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
The previous version of am335x-fb.c contained the functionalities of two
drivers that this patch has split. It was a video type driver that used
the same registration compatible string that now registers a panel type
driver. The proof of this is that two compatible strings were referred
to within the same driver.
There are now two drivers, each with its own compatible string,
functions and API.
Furthermore, the panel driver, in addition to decoding the display
timings, is now also able to manage the backlight.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Simon Glass <sjg@chromium.org>
Up till this commit passing NULL as input parameter was allowed, but not
handled properly. When a NULL parameter was passed to the function a data
abort was raised.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Simon Glass <sjg@chromium.org>
There have been several changes to the am33xx.dtsi, so this patch
re-syncs it with Linux.
Let's add proper interconnect hierarchy for l4 interconnect instances
with the related ti-sysc interconnect module data as documented in
Documentation/devicetree/bindings/bus/ti-sysc.txt of the Linux kernel.
With l4 interconnect hierarchy and ti-sysc interconnect target module
data in place, we can simply move all the related child devices to their
proper location and enable probing using ti-sysc.
The am33xx-clock.dtsi file is the same as that of the Linux kernel,
except for the reg property of the node l4-wkup-clkctrl@0.
As for the am33xx.dtsi file, all the devices with drivers not yet
implemented and those I was able to test with this patch have been moved
to am33xx-l4.dtsi. In case of any regressions, problem devices can be
reverted by moving them back and removing the related interconnect
target module node.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
We can handle the sysc interconnect target module in a generic way for
many TI SoCs. Initially let's just enable domain clocks before the
children are probed.
The code is loosely based on the drivers/bus/ti-sysc.c of the Linux
kernel version 5.9-rc7.
For DT binding details see:
- Documentation/devicetree/bindings/bus/ti-sysc.txt
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Update the ddr settings to use the DDR reg config tool rev 0.5.0.
This enables 4266MTs DDR configuration.
Signed-off-by: Praneeth Bajjuri <praneeth@ti.com>
Signed-off-by: Kevin Scholz <k-scholz@ti.com>
The sequence number assigned for USB subsystem in a uclass is dependent on
the order of occurrence in the device tree. If the dr_mode of USB3SS0
controller is varied then the sequence number of USB3SS1 controller also
changes. If aliases are added then sequence numbers are assigned using the
alias number. This makes the sequence number of USB3SS1 controller
independent of USB3SS0 controller's dr_mode.
Therefore, add aliases to fix the sequence number assigned to the USB
subsystems.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Some Bluetooth controllers, like the BCM4345C5 of the Orange Pi 3,
ship with the controller default address.
Add a config option to fix it up so it can function properly.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Tested-by: Ondrej Jirman <megous@megous.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
[rebased]
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
It turns out that in rare cases, current analytical approach to detect
correct DRAM bus width and rank on H6 doesn't work. On some TV boxes
with DDR3, incorrect DRAM configuration triggers write leveling error
which immediately stops initialization process. Exact reason why this
error appears isn't known. However, if correct configuration is used,
initalization works without problem.
In order to fix this issue, simply try another configuration when any
kind of error appears during initialization, not just those related to
rank and bus width.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Tested-by: Thomas Graichen <thomas.graichen@googlemail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
For the sake of consistency (*) and order of initialization, i.e.
after we have got the ethernet address, interrupt and timer initialized,
try to initialize USB ethernet gadget.
*) for example, zynqmp uses same order.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
So far we did not support the BootROM based FEL USB debug mode on the
64-bit builds for Allwinner SoCs: The BootROM is using AArch32, but the
SPL runs in AArch64.
Returning back to AArch32 was not working as expected, since the RMR
reset into 32-bit mode always starts execution in the BootROM, but not
in the FEL routine.
After some debug and research and with help via IRC, the CPU hotplug
mechanism emerged as a solution: If a certain R_CPUCFG register contains
some magic, the BootROM will immediately branch to an address stored in
some other register. This works well for our purposes.
Enable the FEL feature by providing early AArch32 code to first save the
FEL state, *before* initially entering AArch64.
If we eventually determine that we should return to FEL, we reset back
into AArch32, and use the CPU hotplug mechanism to run some small
AArch32 code snippet that restores the initially saved FEL state.
That allows the normal AArch64 SPL build to be loaded via the sunxi-fel
tool, with it returning into FEL mode, so that other payloads can be
transferred via FEL as well.
Tested on A64, H5 and H6.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Priit Laes <plaes@plaes.org> (on Olimex A64-Olinuxino)
The is_boot0_magic macro is missing parentheses around the macro
argument, breaking any usage with a more complex argument.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
To be able to easily share the Allwinner eGON BROM header structure
between the tools and the SPL code, move the struct definition into a
separate header file.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Samuel Holland <samuel@sholland.org>
PineCube is an IP camera development kit released by Pine64.
It comes with the following compoents:
- A mainboard with Sochip S3 SoC, a 16MByte SPI Flash, AXP209 PMIC,
a power-only microUSB connector, a USB Type-A connector, a 10/100Mbps
Ethernet port and FPC connectors for camera and daughter board.
- An OV5640-based camera module which is connected to the parallel CSI
bus of the mainboard.
- A daughterboard with several buttons, a SD slot, some IR LEDs, a
microphone and a speaker connector.
As the device tree is synchronized in a previous commit, just add it to
Makefile, create a new MAINTAINER item and provide a defconfig.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Import the Beelink GT-King/Pro and supporting meson-g12b-w400.dtsi file
from Linux 5.10.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Import the WeTek Core2 and supporting meson-gx-p23x-q20x.dtsi files
from Linux 5.10.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add SoC revision to environment. This can be useful to select the
correct device tree at runtime (N2/N2+).
Signed-off-by: Pascal Vizeli <pvizeli@syshack.ch>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Move loading of socinfo into a separate function so the value can be
reused later.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add support for the Amlogic based libretech cc version 2.
As version 1, it is based on the s905x SoC.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
[narmstrong: Fixed libretech-cc.rst bullet points]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Sync the libretech cc v2 device tree from Linux v5.10-rc1
commit 3650b228f83a ("Linux 5.10-rc1")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
SPI flash on this machine is located on bus 1, default to using bus 1
for SPI flash and stop aliasing it to bus 0.
Signed-off-by: Hugh Cole-Baker <sigmaris@gmail.com>
Suggested-by: Simon Glass <sjg@chromium.org>
Fixes: c4cea2bb ("rockchip: Enable building a SPI ROM image on bob")
TXC line is directly connected from the SoC to the KSZ9131 PHY. There
is a transient state on this signal, before configuring it to RGMII,
which leads to packet transmit being blocked.
Keeping a pull-up when muxing this pin as function A (G0_TXCK) fixes
the issue.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Add node for flx1 i2c1 subnode (and alias to bus 0)
This bus has two eeprom devices connected.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Enable sdmmc0 on this board. A non-removable eMMC is connected on this
block.
Configure pincontrol accordingly.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
SDMMC1 requires clock specification with assigned-clocks, such that
the PMC will know which parent to assign and the initial start-up frequency.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Get rid of software defined MCK and switch to PMC bindings
for IPs currently present in device tree.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
arm64:
- DT updates
microblaze:
- Add support for NOR device support
spi:
- Fix unaligned data write issue
nand:
- Minor code change
xilinx:
- Fru fix in limit calculation
- Fill git repo link for all Xilinx boards
video:
- Add support for seps525 spi display
tools:
- Minor Vitis file support
cmd/common
- Minor code indentation fixes
serial:
- Uartlite debug uart initialization fix
-----BEGIN PGP SIGNATURE-----
iFsEABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCX/ROlgAKCRDKSWXLKUoM
IRC5AIkBzg4Sz8fQgdCiOK89k7tdFKMAnA9SYhgm4TSCzffZCJwnm78QoGAC
=4FnY
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2021.04' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2021.04
arm64:
- DT updates
microblaze:
- Add support for NOR device support
spi:
- Fix unaligned data write issue
nand:
- Minor code change
xilinx:
- Fru fix in limit calculation
- Fill git repo link for all Xilinx boards
video:
- Add support for seps525 spi display
tools:
- Minor Vitis file support
cmd/common
- Minor code indentation fixes
serial:
- Uartlite debug uart initialization fix
The GPIO hog flags are ignored by gpiolib-of.c now, set the flags to 0.
Since GPIO_ACTIVE_HIGH is defined as 0, this change only increases the
correctness of the DT.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The GPIO hog flags are ignored by gpiolib-of.c now, set the flags to 0.
Due to a change in gpiolib-of.c, setting flags to GPIO_ACTIVE_LOW and
using output-low DT property leads to the GPIO being set high instead.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Driver model: Rename U_BOOT_DEVICE et al.
dtoc: Tidy up and add more tests
ns16550 code clean-up
x86 and sandbox minor fixes for of-platdata
dtoc prepration for adding build-time instantiation
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl/09LURHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIrebjwwf/fHRjYsAY/Yj/+y1xgo3L3sphIvQUqTDF
KkLl+kHdV5r8W/HJULxLQcF2r7pcPEI6TAQxuj3qQ5SUvm2HviS8GHGPawDEwyht
HgBp9VD56+HUadMfnbG//DVS73ycbL4XSKlYqpkINEejtnlttsCIawUXX5cTyGM/
59VkgnKrKvJQRUXvYLa8MTugTs4fkPJGDqhActBk/7SP1SImj+rfalNSqA2/dx6y
2RnPCSzB1x2231KSj+B1NgGlR3Xb8P8zgh20ijcEU/hrlXBTZyi7K7f4SJR30Efu
LYkkuj4VbxcV/25RozR0fmknqCs0QyAI+/dql6TNtbTSPC/jAfj0jQ==
=9kN3
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-5jan21' of git://git.denx.de/u-boot-dm into next
Driver model: make some udevice fields private
Driver model: Rename U_BOOT_DEVICE et al.
dtoc: Tidy up and add more tests
ns16550 code clean-up
x86 and sandbox minor fixes for of-platdata
dtoc prepration for adding build-time instantiation
In the spirit of using the same base name for all of these related macros,
rename this to have the operation at the end. This is not widely used so
the impact is fairly small.
Signed-off-by: Simon Glass <sjg@chromium.org>
The current macro is a misnomer since it does not declare a device
directly. Instead, it declares driver_info record which U-Boot uses at
runtime to create a device.
The distinction seems somewhat minor most of the time, but is becomes
quite confusing when we actually want to declare a device, with
of-platdata. We are left trying to distinguish between a device which
isn't actually device, and a device that is (perhaps an 'instance'?)
It seems better to rename this macro to describe what it actually is. The
macros is not widely used, since boards should use devicetree to declare
devices.
Rename it to U_BOOT_DRVINFO(), which indicates clearly that this is
declaring a new driver_info record, not a device.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present ofnode is present in the device even if it is never used. With
of-platdata this field is not used, so can be removed. In preparation for
this, change the access to go through inline functions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Most drivers use these access methods but a few do not. Update them.
In some cases the access is not permitted, so mark those with a FIXME tag
for the maintainer to check.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
