This patch fixes eeprom page size so that you can now write more than
64 bytes at a time.
It also makes the board take MAC addresses, if found, from EEPROM.
User should place up to 4 addresses at offset 0x7f00, for
eth{,1,2,3}addr. Any unused addresses should be zero. This group of
four six-byte values should have it's CRC at the end. crc32 and
eeprom commands can be used to accomplish this.
If CRC fails, MAC addresses come from the environment. If CRC
succeeds, the environment is overwritten at startup.
Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Commit 55774b512f broke the onboard USB
controller on the PCI bus in Linux on the MPC8323ERDB.
This fixes it by defining CONFIG_PCI_SKIP_HOST_BRIDGE in the board's
config file.
Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Enable the first two SATA interfaces on MPC837xEMDS board,
The two SATA ports are on LYNX1. (SATA0/1 on J4/5)
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch is stolen from Anton Vorontsov's patch
for mpc837xerdb boards.
The reference clk and xcorevdd voltage of serdes1/2
is same between mpc837xemds and mpc837xerdb.
8377E: LYNX1- 2 SATA LYNX2- 2 PCIE
8378E: LYNX1- 2 SGMII LYNX2- 2 PCIE
8379E: LYNX1- 2 SATA LYNX2- 2 SATA
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Canyonlands (460EX) shares the first PCIe interface with the SoC SATA
interface. This usage can be configured with the jumper J6. This patch
displays the current configuration upon bootup and changes the PCIe
init loop, to only initialize the availabel PCIe slots.
Signed-off-by: Stefan Roese <sr@denx.de>
R2D plus is SH reference board used with SH7751R.
This board has 266Mhz CPU, 64MB SDRAM, Cardbus, CF interface,
one PCI bus, VGA, and two Ethernet controller.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Renesas Solutions R7780MP is a reference board on SH7780.
This board has serial, 10/100 base Ethernet deivice, CF slot
and VGA devices. This board can set extension board.
Extension board has 10/100/1000 base Ethernet device, PCI slot,
S-ATA, iDVR slot.
Signed-off-by: Yusuke Goda <goda.yusuke@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Migo-R is a board based on SH7722 and has may devices.
In this patch, supported SCIF, NOR flash and Ethernet.
Signed-off-by: Yusuke Goda <goda.yusuke@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Since all ECC related problems seem to be resolved on LWMON5, this patch
now enables ECC support.
We have to write the ECC bytes by zeroing and flushing in smaller
steps, since the whole 256MByte takes too long for the external
watchdog.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch contains updates for changes for the Korat PPC440EPx board.
These changes include:
(1) Support for "permanent" and "upgradable" copies of U-Boot, as
described in the new "doc/README.korat" file;
(2) a new memory map for the registers in the board's CPLD;
(3) a revised format for manufacturer's data in serial EEPROM; and
(4) changes to track updates to U-Boot for the Sequoia board.
Signed-off-by: Larry Johnson <lrj@acm.org>
Since this board will probably be ported to arch/powerpc in the
near future, we add device tree support now. This way we are
"ready" for arch/powerpc from now on.
Signed-off-by: Stefan Roese <sr@denx.de>
If CFG_MEM_TOP_HIDE is defined in the board config header, this specified
memory area will get subtracted from the top (end) of ram and won't get
"touched" at all by U-Boot. By fixing up gd->ram_size the Linux kernel
should gets passed the now "corrected" memory size and won't touch it
either. This should work for arch/ppc and arch/powerpc. Only Linux board
ports in arch/powerpc with bootwrapper support, which recalculate the
memory size from the SDRAM controller setup, will have to get fixed
in Linux additionally.
This patch enables this config option on some PPC440EPx boards as a workaround
for the CHIP 11 errata. Here the description from the AMCC documentation:
CHIP_11: End of memory range area restricted access.
Category: 3
Overview:
The 440EPx DDR controller does not acknowledge any
transaction which is determined to be crossing over the
end-of-memory-range boundary, even if the starting address is
within valid memory space. Any such transaction from any PLB4
master will result in a PLB time-out on PLB4 bus.
Impact:
In case of such misaligned bursts, PLB4 masters will not
retrieve any data at all, just the available data up to the
end of memory, especially the 440 CPU. For example, if a CPU
instruction required an operand located in memory within the
last 7 words of memory, the DCU master would burst read 8
words to update the data cache and cross over the
end-of-memory-range boundary. Such a DCU read would not be
answered by the DDR controller, resulting in a PLB4 time-out
and ultimately in a Machine Check interrupt. The data would
be inaccessible to the CPU.
Workaround:
Forbid any application to access the last 256 bytes of DDR
memory. For example, make your operating system believe that
the last 256 bytes of DDR memory are absent. AMCC has a patch
that does this, available for Linux.
This patch sets CFG_MEM_TOP_HIDE for the following 440EPx boards:
lwmon5, korat, sequoia
The other remaining 440EPx board were intentionally not included
since it is not clear to me, if they use the end of ram for some
other purpose. This is unclear, since these boards have CONFIG_PRAM
defined and even comments like this:
PMC440.h:
/* esd expects pram at end of physical memory.
* So no logbuffer at the moment.
*/
It is strongly recommended to not use the last 256 bytes on those
boards too. Patches from the board maintainers are welcome.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds support for the AMCC Glacier 460GT eval board.
The main difference to the Canyonlands board are listed here:
- 4 ethernet ports instead of 2
- no SATA port
- no USB port
Currently EMAC2+3 are not working. This will be fixed in a later
release.
Signed-off-by: Stefan Roese <sr@denx.de>
original ata_piix driver is using IDE framework, not real
SATA framework. For now, the ata_piix driver is only used
by x86 sc520_cdp board. This patch makes the ata_piix driver
use the new SATA framework, so
- remove the duplicated command stuff
- remove the CONFIG_CMD_IDE define in the sc520_cdp.h
- add the CONFIG_CMD_SATA define to sc520_cdp.h
Signed-off-by: Dave Liu <daveliu@freescale.com>
move the cmd_sata.c from common/ to drivers/ata_piix.c,
the cmd_sata.c have some part of ata_piix controller drivers.
consolidate the driver to have better framework.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Each file that can be built here now follows some
CONFIG_ option so that they are appropriately built
or not, as needed. And CONFIG_ defines were added
to various board config files to make sure that happens.
The other board/freescale/*/Makefiles no longer need
to reach up and over into ../common to build their
individually needed files any more.
Boards that are CDS specific were renamed with cds_ prefix.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
When we go to 36-bit physical addresses we need to keep the concept of
the physical CCSRBAR address seperate from the virtual one.
For the majority of boards CFG_CCSBAR_PHYS == CFG_CCSRBAR
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Linux understands "host" (default), "peripheral" and "otg" (broken).
Though, U-Boot doesn't restrict dr_mode variable to these values (think
of renames in future).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
With the original value of 1/2 clock cycle delay, the system ran relatively
stable except when we run benchmarks that are intensive users of memory.
When I run samba connected disk with a HDBENCH test, the system locks-up
or reboots sporadically.
Signed-off by: Joe D'Abbraccio <Joe.D'abbraccio@freescale.com>
The device trees for these boards describe PCI I/O as starting from
address zero from the device's perspective.
Placing I/O elsewhere may cause problems with certain PCI boards, and may
cause problems with Linux.
Signed-off-by: Scott Wood <scottwood@freescale.com>
At least on the "33MHz Pilot" board crystal is actually 33.3MHz.
This patch fixes "system time drifting" problem.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Plus modify environment to use it and remove bootfile env variable,
it is internal and CONFIG_BOOTFILE is used for these purposes.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Current DDR setup easily causes memory corruption, this patch fixes it.
Also fix TIMING_CFG0_MRS_CYC definition.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
On the MPC8377ERDB: 2 SATA and 2 PCI-E.
On the MPC8378ERDB: 2 PCI-E
On the MPC8379ERDB: 4 SATA
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
There's no on-board RTC on the MPC8323ERDB, but there is an EEPROM.
Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
The following changes are based on kernel UCC ethernet performance:
1. Make the CSB bus pipeline depth as 4, and enable the repeat mode
2. Optimize transactions between QE and CSB. Added CFG_SPCR_OPT
switch to enable this setting.
The following changes are based on the App Note AN3369 and
verified to improve memory latency using LMbench:
3. CS0_CONFIG[AP_n_EN] is changed from 1 to 0
4. CS0_CONFIG[ODT_WR_CONFIG] set to 1. Was a reserved setting
previously.
5. TIMING_CFG_1[WRREC] is changed from 3clks to 2clks (based on
Twr=15ns, and this was already the setting in DDR_MODE)
6. TIMING_CFG_1[PRETOACT] is changed from 3clks to 2clks. (based on
Trp=15ns)
7. TIMING_CFG_1[ACTTOPRE] is changed from 9clks to 6clks. (based on
Tras=40ns)
8. TIMING_CFG_1[ACTTORW] is changed from 3clks to 2clks. (based on
Trcd=15ns)
9. TIMING_CFG_1[REFREC] changed from 21 clks to 11clks. (based on
Trfc=75ns)
10. TIMING_CFG_2[FOUR_ACT] is changed from 10 clks to 7clks. (based
on Tfaw=50ns)
11. TIMING_CFG_2[ADD_LAT] and DDR_MODE[AL] changed from 0 to 1 (based
on CL=3 and WL=2).
Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Use available shift/mask macros to define DDR configuration.
Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Update the MPC8349E-mITX, MPC8313E-RDB, and MPC837XE-RDB board files to upload
the Vitesse VSC7385 firmware. Changed CONFIG_VSC7385 to CONFIG_VSC7385_ENET.
Cleaned up the board header files to make selecting the VSC7385 easier to
control.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
These defines embedded the u-boot env variables and/or the bd_t structure
in the fdt blob. The conclusion of discussion on the u-boot email list
was that embedding these in the fdt blob is not useful: there are better
ways of passing the data (in fact, the fdt blob itself replaces the
bd_t struct).
The only board that enables these is the stxxtc and they don't appear
to be used by linux.
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
- insert partition for dtb blob to TQM5200B MTD layout
- set env variables dependent on the configured board
(TQM5200 or TQM5200B)
Signed-off-by: Martin Krause <martin.krause@tqs.de>
To enable this, alternative, configuration the U-Boot board configuration
file for lwmon5 includes the definitions of alternative addresses for header
(CONFIG_ALT_LH_ADDR) and buffer (CONFIG_ALT_LB_ADDR).
The Linux shall be configured with the CONFIG_ALT_LB_LOCATION option set,
and has the BOARD_ALT_LH_ADDR and BOARD_ALT_LB_ADDR constants defined in the
lwmon5 board-specific header (arch/ppc/platforms/4xx/lwmon5.h).
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
