Move MTD-related lines out of the root Makefile. Put them in their
respective directories. Enclose some of these new lines to skip them
when building the SPL. MTD core files and some MTD device drivers are
compiled in a mtd.o object and included in the final object only if
MTD support is required (there are two different symbols for that, one
for U-Boot and one for the SPL).
Now that all defconfigs have been fixed, we can stop the logic where
enabling a command selects the core files to compile. This logic is
broken since selecting a symbol with a 'depends on' will not enforce
this secondary dependency.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add Support for UFS Host Controller Interface (UFSHCI) for communicating
with Universal Flash Storage (UFS) devices. The steps to initialize the
host controller interface are the following:
- Initiate the Host Controller Initialization process by writing to the
Host controller enable register.
- Configure the Host Controller base address registers by allocating a
host memory space and related data structures.
- Unipro link startup procedure
- Check for connected device
- Configure UFS host controller to process requests
Also register this host controller as a SCSI host controller.
Taken from Linux Kernel v5.2 (drivers/scsi/ufs/ufshcd.c) and ported to
U-boot.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
This adds separate kconfig options for drivers/sysreset and
drivers/firmware.
Up to now, CONFIG_SPL_DRIVERS_MISC_SUPPORT added drivers/misc to SPL
build but also added drivers/firmware and drivers/sysreset at the same
time.
Since that is confusing, this patch uses CONFIG_SPL_SYSRESET for
drivers/sysreset and adds CONFIG_SPL_FIRMWARE for
drivers/firmware (and accordingly for the TPL options).
CONFIG_SPL_DRIVERS_MISC_SUPPORT stays for including drivers/misc into
the SPL build (and accordingly for TPL) since there are boards using
non-DM (non UCLASS_MISC) files from drivers/misc. Such boards don't
have CONFIG_SPL_MISC enabled, so cannot use this to include
drivers/misc into the SPL build.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Introduce new UCLASS_PCI_EP class for handling PCI endpoint
devices, allowing to set various attributes of the PCI endpoint
device, such as:
* configuration space header
* BAR definitions
* outband memory mapping
* start/stop PCI link
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The cache UCLASS will be used for configure settings that can be found
in a CPU's L2 cache controller.
Add a uclass and a test for cache.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
At present this uclass is selected only on x86. In order to add a test for
it, it must also support sandbox. Create a new CONFIG_PCH option and
enable it on x86 and sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Do this by using $(SPL_) in Makefiles and CONFIG_IS_ENABLED in C code.
This ensures the files and features are only built into the right build
for which they are enabled. Using the macros to simplify this patch was
made possible by the config symbol rename done in the last patch.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
The symbol CONFIG_SPL_DFU_SUPPORT in SPL build has the same
meaning as CONFIG_DFU in regular U-Boot. Drop the _SUPPORT
to allow for cleaner use in code.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
Some drivers might need to access common USB functions such as
usb_get_maximum_speed() or usb_get_dr_mode().
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Building U-Boot with CONFIG_PCI and CONFIG_DM_PCI enabled, but
CONFIG_SPL_PCI_SUPPORT disabled, results in following linker
error:
lib/built-in.o: In function `fdtdec_get_pci_bar32':
lib/fdtdec.c:305: undefined reference to `dm_pci_read_bar32'
fdtdec.c:305:(.text.fdtdec_get_pci_bar32+0x24): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `dm_pci_read_bar32'
This is because reference to dm_pci_read_bar32() remains in lib/fdtdec.c
while SPL build does not descend into drivers/pci directory in
drivers/Makefile if CONFIG_SPL_PCI_SUPPORT is not enabled.
Fix this by applying appropriate #define guards in lib/fdtdec.c.
It looks like ns16550.c has the same problem, so fixed that too.
To simplify this, CONFIG_SPL_PCI_SUPPORT is renamed to CONFIG_SPL_PCI
(enables use of CONFIG_IS_ENABLED() macro).
Suggested-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The function part_init() will only be built when we have both
CONFIG_PARTITIONS and CONFIG_HAVE_BLOCK_DEVICE set. Protect the call to
this function with both of these tests now.
Cc: Simon Glass <sjg@chromium.org>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Cc: Mingkai Hu <mingkai.hu@nxp.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Marek Behún <marek.behun@nic.cz>
Cc: Vanessa Maegima <vanessa.maegima@nxp.com>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Adam Ford <aford173@gmail.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This is uclass for Hardware Spinlocks.
It implements two mandatory operations: lock and unlock
and one optional relax operation.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
At present these subsystems are only supported in U-Boot proper but it is
sometimes necessary to support them in SPL, or even TPL. Update the
Kconfig and Makefile to support this. Also adjust GPIO so that it can be
used in TPL if required.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
This adds a new virtio uclass driver for “virtio” [1] family of
devices that are are found in virtual environments like QEMU,
yet by design they look like physical devices to the guest.
The uclass driver provides child_pre_probe() and child_post_probe()
methods to do some common operations for virtio device drivers like
device and driver supported feature negotiation, etc.
[1] http://docs.oasis-open.org/virtio/virtio/v1.0/virtio-v1.0.pdf
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Adds a uclass to interface with a TEE (Trusted Execution Environment).
A TEE driver is a driver that interfaces with a trusted OS running in
some secure environment, for example, TrustZone on ARM cpus, or a
separate secure co-processor etc.
The TEE subsystem can serve a TEE driver for a Global Platform compliant
TEE, but it's not limited to only Global Platform TEEs.
The over all design is based on the TEE subsystem in the Linux kernel,
tailored for U-Boot.
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Igor Opaniuk <igor.opaniuk@linaro.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
This is the PR for SPI-NAND changes along with few spi changes.
[trini: Re-sync changes for ls1012afrwy_qspi*_defconfig]
Signed-off-by: Tom Rini <trini@konsulko.com>
Since there is no canonical "board device" that can be used in board
files, it is difficult to use DM function for board initialization in
these cases.
Hence, add a uclass that implements a simple "board device", which can
hold devices not suitable anywhere else in the device tree, and is also
able to read encoded information, e.g. hard-wired GPIOs on a GPIO
expander, read-only memory ICs, etc. that carry information about the
hardware.
The devices of this uclass expose methods to read generic data types
(integers, strings, booleans) to encode the information provided by the
hardware.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
We might want to access data stored onto one wire EEPROMs.
Create a framework to provide a consistent API.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
[eugen.hristev@microchip.com: reworked patch]
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
We might want to use 1-Wire devices connected on boards such as EEPROMs in
U-Boot.
Provide a framework to be able to do that.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
[eugen.hristev@microchip.com: reworked]
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
NAND flavors, like serial and parallel, have a lot in common and would
benefit to share code. Let's move raw (parallel) NAND specific code in a
raw/ subdirectory, to ease the addition of a core file in nand/ and the
introduction of a spi/ subdirectory specific to SPI NANDs.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add a uclass for AXI (Advanced eXtensible Interface) busses, and a
driver for the gdsys IHS AXI bus on IHS FPGAs.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add CONFIG_SPL_POWER_DOMAIN config entry.
Build drivers/power/domain if this config is selected.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
This is a uclass for Shared memory manager drivers.
A Shared Memory Manager driver implements an interface for allocating
and accessing items in the memory area shared among all of the
processors.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Rename CONFIG_SPL_RESET_SUPPORT to CONFIG_SPL_DM_RESET, so can use
CONFIG_IS_ENABLED(DM_RESET) checking in reset.h later.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add drivers/fastboot/fb_common.c, where fastboot_okay/fail are implemented
so we can call them from a non-USB implementation.
Introduce fastboot_response which takes varargs parameters so we can
use it to generate formatted response strings. Refactor fastboot_okay/fail
to use it.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Separate CMD_FASTBOOT from FASTBOOT and move code and configuration to
drivers/fastboot.
Switch dependencies on FASTBOOT to USB_FUNCTION_FASTBOOT as anyone who wants
FASTBOOT before this series wants USB_FUNCTION_FASTBOOT. Split
USB_FUNCTION_FASTBOOT from FASTBOOT so they retain their existing
behaviour.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
USB PHY implementation for Allwinner SOC's can be handling
in to single driver with different phy configs.
This driver handle all Allwinner USB PHY's start from 4I to
50I(except 9I). Currently added A64 compatibility more will
add in next coming patches.
Current implementation is unable to get pinctrl, clock and reset
details from DT since the dm code on these will add it future.
Driver named as phy-sun4i-usb.c since the same PHY logic
work for all Allwinner SOC's start from 4I to A64 except 9I
with different phy configurations.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
New, SPL related config option - CONFIG_SPL_BOOTCOUNT_LIMIT has been
added to allow drivers/bootcount code re-usage in SPL.
This code is necessary to use and setup bootcount in SPL in the case of
falcon boot mode.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Alex Kiernan <alex.kiernan@gmail.com>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
Add option to include RESET driver and uclass in SPL.
That can be useful to handle IP reset with same driver
in U-Boot and in SPL.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Rename CONFIG_SPL_USBETH_SUPPORT to CONFIG_SPL_USB_ETHER.
This enables users to block text using CONFIG_IS_ENABLED() instead
of resorting to #if ladders with SPL and non-SPL cases.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
The dra7xx series of SOCs contain a temperature sensor and an
associated analog-to-digital converter (ADC) which produces
an output which is proportional to the SOC temperature.
Add support for this temperature sensor.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
NVM Express (NVMe) is a register level interface that allows host
software to communicate with a non-volatile memory subsystem. This
interface is optimized for enterprise and client solid state drives,
typically attached to the PCI express interface.
This adds a U-Boot driver support of devices that follow the NVMe
standard [1] and supports basic read/write operations.
Tested with a 400GB Intel SSD 750 series NVMe card with controller
id 8086:0953.
[1] http://www.nvmexpress.org/resources/specifications/
Signed-off-by: Zhikang Zhang <zhikang.zhang@nxp.com>
Signed-off-by: Wenbin Song <wenbin.song@nxp.com>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
To fully support DM timer in SPL and TPL, we need a few things cleaned
up and normalised:
- inclusion of the uclass and drivers should be an all-or-nothing
decision for each stage and under control of $(SPL_TPL_)TIMER
instead of having the two-level configuration with TIMER and
$(SPL_TPL_)TIMER_SUPPORT
- when $(SPL_TPL_)TIMER is enabled, the ARMv8 generic timer code can
not be compiled in
This normalises configuration to $(SPL_TPL_)TIMER and moves the config
options to drivers/timer/Kconfig (and cleans up the collateral damage
to some defconfigs that had SPL_TIMER_SUPPORT enabled).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
To simplify drivers/Makefile a bit when using TPL/SPL, we consistently
use the $(SPL_TPL_) macro to test for drivers that have separate
configuration symbols for the full U-boot, SPL and TPL stages.
Instead of explicitly repeating them in two separate if-guarded
sections of the Makefile, we can now simply list these options once.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enable FPGA driver build for Arria 10 SPL because FPGA driver is
needed by Arria 10 SPL to configure and getting DDR up before
loading U-boot into DDR and booting from there.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Dinh Nguyen <dinguyen@kernel.org>
At present we have the SCSI drivers in the drivers/block and common/
directories. It is better to split them out into their own place. Use
drivers/scsi which is what Linux does.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present we have the SATA and PATA drivers mixed up in the drivers/block
directory. It is better to split them out into their own place. Use
drivers/ata which is what Linux does.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This subsystem is quite old. It has been replaced with a driver-model
version (UCLASS_THERMAL). Boards are free to convert to that if required,
but here is a removal patch that could be applied in the meantime.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
This subsystem has not been converted to driver model, there is only one
driver and only one board that uses it. Drop it and its CONFIG option.
Also drop the rtc4543 RTC driver since it uses TWS.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This simplifies makefiles. Also, arrange the order of objects in
drivers/mmc/Makefile so that the framework objects are listed before
drivers.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The PHY framework provides a set of APIs to control a PHY. This API is
derived from the linux version of the generic PHY framework.
Currently the API supports init(), deinit(), power_on, power_off() and
reset(). The framework provides a way to get a reference to a phy from the
device-tree.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
If the system is running PSCI firmware, the System Reset function
(func ID: 0x80000009) is supposed to be handled by PSCI, that is,
the SoC/board specific reset implementation should be moved to PSCI.
U-Boot should call the PSCI service according to the arm-smccc
manner.
The arm-smccc is supported on ARMv7 or later. Especially, ARMv8
generation SoCs are likely to run ARM Trusted Firmware BL31. In
this case, U-Boot is a non-secure world boot loader, so it should
not be able to reset the system directly.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Since TPL often needs to be very very small it may not make sense to
enable driver model. Add an option for this.
This changes brings the 'rock' board under the TPL limit with gcc 4.9.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add an option for building Platorm Controller Hub drivers in SPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a new Kconfig option to allow timer drivers to be used in SPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a new Kconfig option to allow RTC drivers to be used in SPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a new Kconfig option to allow PCI drivers to be used in SPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a new Kconfig option to allow CPU drivers to be used in SPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Introduce USB Gadget config option. This allows to combine Makefile
entries for SPL_USBETH_SUPPORT and SPL_DFU_SUPPORT.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Ravi Babu <ravibabu@ti.com>
The DFU Kconfig menu entries should be part of the SPL
Kconfig file. Also avoid using the top level Makefile by
moving the config dependent build artifacts to the driver/
and driver/usb/gadget/ Makfiles.
With that, DFU can be built again in SPL if
CONFIG_SPL_DFU_SUPPORT is enabled.
Fixes: 6ad6102246 ("usb:gadget: Disallow DFU in SPL for now")
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
This version is based on the Marvell U-Boot version with this patch
applied as latest patch:
Git ID 7f408573: "fix: comphy: cp110: add comphy initialization for usb
device mode" from 2016-07-05.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
At present TPL uses the same options as SPL support. In a few cases the board
config enables or disables the SPL options depending on whether
CONFIG_TPL_BUILD is defined.
With the move to Kconfig, options are determined for the whole build and
(without a hack like an #undef in a header file) cannot be controlled in this
way.
Create new TPL options for these and update users. This will allow Kconfig
conversion to proceed for these boards.
Signed-off-by: Simon Glass <sjg@chromium.org>
Create drivers/sysreset and move sysreset-uclass and all sysreset
drivers there.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Booting a payload out of NAND FLASH from the SPL is a crux today, as
it requires hard partioned FLASH. Not a brilliant idea with the
reliability of todays NAND FLASH chips.
The upstream UBI + UBI fastmap implementation which is about to
brought to u-boot is too heavy weight for SPLs as it provides way more
functionality than needed for a SPL and does not even fit into the
restricted SPL areas which are loaded from the SoC boot ROM.
So this provides a fast and lightweight implementation of UBI scanning
and UBI fastmap attach. The scan and logical to physical block mapping
code is developed from scratch, while the fastmap implementation is
lifted from the linux kernel source and stripped down to fit the SPL
needs.
The text foot print on the board which I used for development is:
6854 0 0 6854 1abd
drivers/mtd/ubispl/built-in.o
Attaching a NAND chip with 4096 physical eraseblocks (4 blocks are
reserved for the SPL) takes:
In full scan mode: 1172ms
In fastmap mode: 95ms
The code requires quite some storage. The largest and unknown part of
it is the number of fastmap blocks to read. Therefor the data
structure is not put into the BSS. The code requires a pointer to free
memory handed in which is initialized by the UBI attach code itself.
See doc/README.ubispl for further information on how to use it.
This shares the ubi-media.h and crc32 implementation of drivers/mtd/ubi
There is no way to share the fastmap code, as UBISPL only utilizes the
slightly modified functions ubi_attach_fastmap() and ubi_scan_fastmap()
from the original kernel ubi fastmap implementation.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
A reset controller is a hardware module that controls reset signals that
affect other hardware modules or chips.
This patch defines a standard API that connects reset clients (i.e. the
drivers for devices affected by reset signals) to drivers for reset
controllers/providers. Initially, DT is the only supported method for
connecting the two.
The DT binding specification (reset.txt) was taken from Linux kernel
v4.5's Documentation/devicetree/bindings/reset/reset.txt.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
This allows a board to configure verified boot within the SPL using
a FIT or FIT with external data. It also allows the SPL to perform
signature verification without needing relocation.
The board configuration will need to add the following feature defines:
CONFIG_SPL_CRYPTO_SUPPORT
CONFIG_SPL_HASH_SUPPORT
CONFIG_SPL_SHA256
In this example, SHA256 is the only selected hashing algorithm.
And the following booleans:
CONFIG_SPL=y
CONFIG_SPL_DM=y
CONFIG_SPL_LOAD_FIT=y
CONFIG_SPL_FIT=y
CONFIG_SPL_OF_CONTROL=y
CONFIG_SPL_OF_LIBFDT=y
CONFIG_SPL_FIT_SIGNATURE=y
Signed-off-by: Teddy Reed <teddy.reed@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Andreas Dannenberg <dannenberg@ti.com>
Acked-by: Sumit Garg <sumit.garg@nxp.com>
A mailbox is a hardware mechanism for transferring small message and/or
notifications between the CPU on which U-Boot runs and some other device
such as an auxilliary CPU running firmware or a hardware module.
This patch defines a standard API that connects mailbox clients to mailbox
providers (drivers). Initially, DT is the only supported method for
connecting the two.
The DT binding specification (mailbox.txt) was taken from Linux kernel
v4.5's Documentation/devicetree/bindings/mailbox/mailbox.txt.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Qualcom processors use proprietary bus to talk with PMIC devices -
SPMI (System Power Management Interface).
On wiring level it is similar to I2C, but on protocol level, it's
multi-master and has simple autodetection capabilities.
This commit adds simple uclass that provides bus read/write interface.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
A Platform Controller Hub is an Intel concept - it is like the peripherals
on an SoC and is often in a separate chip from the CPU. The chip is typically
found on the first PCI bus and integrates multiple devices.
We have a very simple uclass to support PCHs. Add a few operations, such as
setting up the devices on the PCH and finding the SPI controller base
address. Also move it into drivers/pch/ since we will be adding a few PCH
drivers.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Until now, the SoC selection for the ARCH_MVEBU platforms has been done
in the config header. Using CONFIG_ARMADA_XP in a non-clear way. As
it needed to get selected for AXP and A38x based boards. This patch
now changes this to move the SoC selection to Kconfig. And also
uses CONFIG_ARCH_MVEBU as a common define for both AXP and A38x.
This makes things a bit clearer - especially for new board additions.
Additionally the defines CONFIG_SYS_MVEBU_DDR_AXP and
CONFIG_SYS_MVEBU_DDR_A38X are replaced with the already available
CONFIG_ARMADA_38X and CONFIG_ARMADA_XP.
And CONFIG_DDR3 is removed, as its not referenced anywhere.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
After consulting with some of the SPDX team, the conclusion is that
Makefiles are worth adding SPDX-License-Identifier tags too, and most of
ours have one. This adds tags to ones that lack them and converts a few
that had full (or in one case, very partial) license blobs into the
equivalent tag.
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
This commit adds:
- new uclass id: UCLASS_ADC
- new uclass driver: drivers/adc/adc-uclass.c
The new uclass's API allows for ADC operation on:
* single-channel with channel selection by a number
* multti-channel with channel selection by bit mask
ADC uclass's functions:
* single-channel:
- adc_start_channel() - start channel conversion
- adc_channel_data() - get conversion data
- adc_channel_single_shot() - start/get conversion data
* multi-channel:
- adc_start_channels() - start selected channels conversion
- adc_channels_data() - get conversion data
- adc_channels_single_shot() - start/get conversion data for channels
selected by bit mask
* general:
- adc_stop() - stop the conversion
- adc_vdd_value() - positive reference Voltage value with polarity [uV]
- adc_vss_value() - negative reference Voltage value with polarity [uV]
- adc_data_mask() - conversion data bit mask
The device tree can provide below constraints/properties:
- vdd-polarity-negative: if true: Vdd = vdd-microvolts * (-1)
- vss-polarity-negative: if true: Vss = vss-microvolts * (-1)
- vdd-supply: phandle to Vdd regulator's node
- vss-supply: phandle to Vss regulator's node
And optional, checked only if the above corresponding, doesn't exist:
- vdd-microvolts: positive reference Voltage [uV]
- vss-microvolts: negative reference Voltage [uV]
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Many System on Chip(SoC) solutions are complex with multiple processors
on the same die dedicated to either general purpose of specialized
functions. Many examples do exist in today's SoCs from various vendors.
Typical examples are micro controllers such as an ARM M3/M0 doing a
offload of specific function such as event integration or power
management or controlling camera etc.
Traditionally, the responsibility of loading up such a processor with a
firmware and communication has been with a High Level Operating
System(HLOS) such as Linux. However, there exists classes of products
where Linux would need to expect services from such a processor or the
delay of Linux and operating system being able to load up such a
firmware is unacceptable.
To address these needs, we need some minimal capability to load such a
system and ensure it is started prior to an Operating System(Linux or
any other) is started up.
NOTE: This is NOT meant to be a solve-all solution, instead, it tries to
address certain class of SoCs and products that need such a solution.
A very simple model is introduced here as part of the initial support
that supports microcontrollers with internal memory (no MMU, no
execution from external memory, or specific image format needs). This
basic framework can then (hopefully) be extensible to other complex SoC
processor support as need be.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Simon Glass <sjg@chromium.org>
This creates a new framework for handling of pin control devices,
i.e. devices that control different aspects of package pins.
This uclass handles pinmuxing and pin configuration; pinmuxing
controls switching among silicon blocks that share certain physical
pins, pin configuration handles electronic properties such as pin-
biasing, load capacitance etc.
This framework can support the same device tree bindings, but if you
do not need full interface support, you can disable some features to
reduce memory foot print. Typically around 1.5KB is necessary to
include full-featured uclass support on ARM board (CONFIG_PINCTRL +
CONFIG_PINCTRL_FULL + CONFIG_PINCTRL_GENERIC + CONFIG_PINCTRL_PINMUX),
for example.
We are often limited on code size for SPL. Besides, we still have
many boards that do not support device tree configuration. The full
pinctrl, which requires OF_CONTROL, does not make sense for those
boards. So, this framework also has a Do-It-Yourself (let's say
simple pinctrl) interface. With CONFIG_PINCTRL_FULL disabled, the
uclass itself provides no systematic mechanism for identifying the
peripheral device, applying pinctrl settings, etc. They must be
done in each low-level driver. In return, you can save much memory
footprint and it might be useful especially for SPL.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Simon Glass <sjg@chromium.org>
Just preparing for upcoming cleaning.
The board-specific linker script board/vpac270/u-boot-spl.lds
has been touched to avoid build error. It does not change the
size of spl/u-boot-spl.bin for this board, so it should be OK.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Clocks are an important feature of platforms and have become increasing
complex with time. Most modern SoCs have multiple PLLs and dozens of clock
dividers which distribute clocks to on-chip peripherals.
Some SoC implementations have a clock API which is private to that SoC family,
e.g. Tegra and Exynos. This is useful but it would be better to have a
common API that can be understood and used throughout U-Boot.
Add a simple clock API as a starting point. It supports querying and setting
the rate of a clock. Each clock is a device. To reduce memory and processing
overhead the concept of peripheral clocks is provided. These do not need to
be explicit devices - it is possible to write a driver that can adjust the
I2C clock (for example) without an explicit I2C clock device. This can
dramatically reduce the number of devices (and associated overhead) in a
complex SoC.
Clocks are referenced by a number, and it is expected that SoCs will define
that numbering themselves via an enum.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add support for a driver which sets up DRAM and can return information about
the amount of RAM available. This is a first step towards moving RAM init
to driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a simple uclass for LEDs, so that these can be controlled by the device
tree and activated when needed. LEDs are referred to by their label.
This implementation requires a driver for each type of LED (e.g GPIO, I2C).
Signed-off-by: Simon Glass <sjg@chromium.org>
It is useful to be able to keep track of the available CPUs in a multi-CPU
system. This uclass is mostly intended for use with SMP systems.
The uclass provides methods for getting basic information about each CPU.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a new thermal uclass for thermal sensor and implement the imx
thermal driver basing on this uclass.
Signed-off-by: Ye.Li <B37916@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
ls1021 is arm-core and support qe which is u-qe.
add u-qe init for arm board.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
[York Sun: Fix compiling error caused by u_qe_init()]
Reviewed-by: York Sun <yorksun@freescale.com>
This patch split the Keystone II SGMII SerDes related code from
Ethernet driver and create a separate SGMII SerDes driver.
The SerDes driver can be used by others keystone subsystems
like PCI, sRIO, so move it to driver/soc/keystone directory.
Add soc specific drivers directory like in the Linux kernel.
It is going to be used by keysotone soc specific drivers.
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
[1] Move driver/core/, driver/input/ and drivers/input/ entries
from the top Makefile to drivers/Makefile
[2] Remove the conditional by CONFIG_DM in drivers/core/Makefile
because the whole drivers/core directory is already selected
by CONFIG_DM in the upper level
[3] Likewise for CONFIG_DM_DEMO in drivers/demo/Makefile
[4] Simplify common/Makefile - both CONFIG_DDR_SPD and
CONFIG_SPD_EEPROM are boolean macros so they can directly
select objects
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Marek Vasut <marex@denx.de>
add basic support for the pwm modul found on imx6.
Pieces of this code are based on linux code from drivers/pwm/pwm-imx.c
Commit "cd3de83f1476 Linux 3.16-rc4"
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Move AEMIF driver to drivers/memory/ti-aemif.c along with AEMIF
definitions collected in arch/arm/include/asm/ti-common/ti-aemif.h
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
