This patchs add the signal description array for PWM pinctrl settings.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
This patch add the support of PWM controller which can be found at aspeed
ast2600 soc. The pwm supoorts up to 16 channels and it's part function
of multi-function device "pwm-tach controller".
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
Add following two new PCI class codes defines into pci_ids.h include file:
PCI_CLASS_BRIDGE_PCI_NORMAL
PCI_CLASS_BRIDGE_PCI_SUBTRACTIVE
And use these defines in all U-Boot code for describing PCI class codes for
normal and subtractive PCI bridges.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This converts the following to Kconfig:
CONFIG_LCD_INFO
CONFIG_LCD_LOGO
CONFIG_LCD_INFO_BELOW_LOGO
CONFIG_LCD_IN_PSRAM
Cc: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_ATMEL_LCD
CONFIG_ATMEL_LCD_BGR555
CONFIG_ATMEL_LCD_RGB565
CONFIG_GURNARD_SPLASH
Signed-off-by: Tom Rini <trini@konsulko.com>
various minor sandbox improvements
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmI1URkRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreYglAf/eM5MtohjWDBQUyvPiQTIV0iS5Zu7NV7Z
1qkrv4OuwZ+U3djtusP7VIUnmdnQlwbF1fFZzo+JUmtYg59K6ZvgI/S+oJzr17/D
bMh+8FpDggEjJhzwSM5fdImfE1PLp161zUxTWMH25VmB+yxQMGWqZBQls+0GADN5
jT4dGwTn098a2HLvdAqkNwafY0Q1cUQeYg8z2J3gdDdZos2PdQV3TqjbrAS6Pr+Z
jAZV+TfTkU2rk6S7B34Ojzx2dF8e80sRK/o/2/+60kt+dUO+nfS/evOb1kqfj8dx
ULNXEBjS1aMy7Z6TCg/E3uEZLM5xyaTZKTwiNeKMthmOK8ZQ3boRuA==
=9FkF
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-18mar22' of https://source.denx.de/u-boot/custodians/u-boot-dm into next
binman FIT improvements
various minor sandbox improvements
There is seldom a need to refresh at 100Hz and it uses a lot of CPU.
Reduce the rate to 10Hz which seems to be adequate.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some files cannot be written but read-only access is still useful for
tests. Add a fallback to read-only access when needed.
This is useful in CI when opening a large data file provided by docker,
where read/write access would result in copying the file, thus needing
a lot of extra disk space.
Signed-off-by: Simon Glass <sjg@chromium.org>
With all boards now using DM_ETH we determine the value for
CONFIG_FEC_XCV_TYPE at run time, except in the case of the default
fall-back. Set the fallback directly now.
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Now that all boards have been converted, remove the non-DM_ETH code.
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
microblaze:
- Add support for reserved memory
xilinx:
- Update FRU code with MAC reading
zynqmp:
- Remove double AMS setting
- DT updates (mostly for SOMs)
- Add support for zcu106 rev 1.0
zynq:
- Update nand binding
nand:
- Aligned zynq_nand to upstream DT binding
net:
- Add support for ethernet-phy-id
mmc:
- Workaround CD in zynq_sdhci driver also for ZynqMP
- Add support for dynamic/run-time SD config for SOMs
gpio:
- Add driver for slg7xl45106
firmware:
- Add support for dynamic SD config
power-domain:
- Update zynqmp driver with the latest firmware
video:
- Add skeleton driver for DP and DPDMA
i2c:
- Fix i2c to work with QEMU
pinctrl:
- Add driver for zynqmp pinctrl driver
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYjIBkgAKCRDKSWXLKUoM
IYUwAKCYRBxb59BFq4MRvTbNcRZ7H4oGIQCfVUl3x9KZ7nFZaYAaBXFBxwna+PE=
=irCR
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.07-rc1' of https://source.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2022.07-rc1
microblaze:
- Add support for reserved memory
xilinx:
- Update FRU code with MAC reading
zynqmp:
- Remove double AMS setting
- DT updates (mostly for SOMs)
- Add support for zcu106 rev 1.0
zynq:
- Update nand binding
nand:
- Aligned zynq_nand to upstream DT binding
net:
- Add support for ethernet-phy-id
mmc:
- Workaround CD in zynq_sdhci driver also for ZynqMP
- Add support for dynamic/run-time SD config for SOMs
gpio:
- Add driver for slg7xl45106
firmware:
- Add support for dynamic SD config
power-domain:
- Update zynqmp driver with the latest firmware
video:
- Add skeleton driver for DP and DPDMA
i2c:
- Fix i2c to work with QEMU
pinctrl:
- Add driver for zynqmp pinctrl driver
In commit 6f46c7441a ("phy: cadence: Sierra: Add a UCLASS_PHY device for
links"), a separate udevice of type UCLASS_PHY was created for each link.
Therefore, move the corresponding link operations under the link device.
Also, change the uclass of sierra phy to UCLASS_MISC as it is no longer the
phy device.
Fixes: 6f46c7441a ("phy: cadence: Sierra: Add a UCLASS_PHY device for links")
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Georgi Vlaev <g-vlaev@ti.com>
The Rockchip RK3399 eMMC PHY has to be power-cycled while changing its
clock speed to some higher speeds. This is dependent on the desired
SDHCI clock speed, and it looks like the PHY should be powered off while
setting the SDHCI clock in these cases.
Commit ac804143cf ("mmc: rockchip_sdhci: add phy and clock config for
rk3399") attempts to do this in the set_ios_post() hook by setting the
SDHCI clock once more while the PHY is turned off/on as necessary, as
the SDHCI framework does not provide a way to override how it sets its
clock. However, the commit breaks reinitializing the eMMC on a few
boards including chromebook_kevin and reportedly ROCKPro64.
This patch reworks the power cycling to utilize the SDHCI framework
slightly better (using the set_control_reg() hook to power off the PHY
and set_ios_post() hook to power it back on) which happens to fix the
issue, at least on a chromebook_kevin.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The Gigadevice gd25lq128 serial flash exists in different versions,
all which identify themselves using the same JEDEC id.
gd25lq128c:
https://www.gigadevice.com/datasheet/gd25lq128
gd25lq128d:
https://www.gigadevice.com/datasheet/gd25lq128d
However, all versions support quad read, so enable it.
Tested and verified on the Sipeed MAix BiT board.
Fixes: 30b9a28a3f ("mtd: spi-nor-ids: Add Gigadevice gd25lq128 ID")
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Ensure the ASPEED related options are grouped together under the RAM
option when enabling support.
This also makes some minor grammar corrections and renames options so
they present cleanly in menuconfig.
There should be no functional change to the configuration or binary.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Dylan Hung <dylan_hung@aspeedtech.com>
Instead of a special function, send an event after driver model is inited
and adjust the boards which use this function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Generate events when devices are probed or removed, allowing hooks
to be added for these situations.
This is controlled by the DM_EVENT config option.
Signed-off-by: Simon Glass <sjg@chromium.org>
Ethernet phy like dp83867 is using strapping resistors to setup PHY
address. On Xilinx boards strapping is setup on wires which are connected
to SOC where internal pull ups/downs influnce phy address. That's why there
is a need to setup pins properly (via pinctrl driver for example) and then
perform phy reset. I can be workarounded by reset gpio done for mdio bus
but this is not working properly when multiply phys sitting on the same
bus. That's why it needs to be done via ethernet-phy-id driver where dt
binding has gpio reset per phy.
DT binding is available here:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/net/ethernet-phy.yaml
The driver is are reading the vendor and device id from valid phy node
using ofnode_read_eth_phy_id() and creating a phy device.
Kconfig PHY_ETHERNET_ID symbol is used because not every platform has gpio
support.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Link: https://lore.kernel.org/r/70ab7d71c812b2c972d48c129e416c921af0d7f5.1645627539.git.michal.simek@xilinx.com
Avoid a race condition where read transaction is started
keeping expected bytes as 0. Which sometimes would result in sending
STOP signal as no data is expected. Observed on QEMU platform.
Signed-off-by: Sai Pavan Boddu <sai.pavan.boddu@xilinx.com>
Reviewed-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/487c8026791bfd60719403a2df2c54bb0ae99232.1646122610.git.michal.simek@xilinx.com
Add support for dynamic configuration which will takes care of
configuring the SD secure space configuration registers using firmware
APIs, performing SD reset assert and deassert.
High level sequence:
- Check for the PM dynamic configuration support, if no error proceed
with SD dynamic configurations(next steps) otherwise skip the dynamic
configuration.
- Put the SD Controller in reset.
- Configure SD Fixed configurations.
- Configure the SD Slot Type.
- Configure the BASE_CLOCK.
- Configure the 8-bit support.
- Bring the SD Controller out of reset.
In the above steps, apart from the Fixed configurations, remaining all
configurations are dynamic and they will be read from devicetree.
And also remove hardcoded secure register writes, as dynamic sd config
support is added.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/030a3ec041ff3efebd574b4d2b477ad85f12cbce.1645626962.git.michal.simek@xilinx.com
The stdout-path property in the device tree does not necessarily
point at a serial device. On machines such as the Apple M1 laptops
where the serial port isn't easy to access and users expect to see
console output on the integrated display stdout-path may point at
the device tree node for the framebuffer for example.
If stdout-path does not point at a node for a serial device, the
serial_check_stdout() will not find a bound device and will drop
down into code that attempts to use lists_bind_fdt() to bind a
device anyway. However, that fallback code does not check that
the uclass of the device is UCLASS_SERIAL. So if stdout-path points
at the framebuffer instead of the serial device it will return a
UCLASS_VIDEO device. Since the code that calls this function
expects the returned device to be a UCLASS_SERIAL device, U-Boot
will crash as soon as it attempts to send output to the console.
Add a check here to verify that the uclass of the bound device
really is UCLASS_SERIAL. If it isn't, serial_check_stdout() will
return an error and serial_find_console_or_panic() will use the
serial device with sequence number 0 as the console and all is fine.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
When running against RC_OSC_32k, the watchdog may suffer from running
faster than expected, expiring earlier. The Linux kernel adds a 10%
margin to the timeout calculation by slowing down the read clock rate
accordingly. Do the same here, also to have comparable preset values
for both drivers.
Along this, fix the name of the local var holding to frequency - in Hz,
not kHz.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Stefan Roese <sr@denx.de>
If Armada 37xx watchdog is started before U-Boot then CNTR_CTRL_ACTIVE bit
is set, U-Boot armada-37xx-wdt.c driver fails to initialize and so U-Boot
is unable to use or kick this watchdog.
Do not check for CNTR_CTRL_ACTIVE bit and always initialize watchdog. Same
behavior is implemented in Linux kernel driver.
This change allows to activate watchdog in firmware which loads U-Boot.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Since commit 492ee6b8d0 ("watchdog: wdt-uclass.c: handle all DM
watchdogs in watchdog_reset()"), all the watchdog are started when
the config WATCHDOG_AUTOSTART.
To avoid a binary choice none/all, a property u-boot,noautostart
may be added in the watchdog node of the u-boot device tree to not
autostart this watchdog.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
The Aspeed GPIO driver supports the GPIO controllers found in the
AST2400, AST2500 and AST2600 BMC SoCs. The implementation is a cut-down
copy of the upstream Linux kernel driver, adapted for u-boot.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
In the Linux kernel (v5.16) for this SoC there are two separate drivers
- namely sdhci-omap.c and omap_hsmmc.c which have separate set of
compatibles.
The U-Boot's drivers/mmc/omap_hsmmc.c driver supports both eMMC and
SD devices - hence the compatible for SDHCI can be added.
After this change the am335x DTS description can be easier ported
from Linux kernel.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Add the support of the LED IP for bcm6357. This
LED IP supports blinking, fading and pulsating,
but for the moment, only blinking is supported.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
slg7xl45106 is i2c based 8-bit gpo expander, gpo pins are set and get by
writing and reading corresponding gpo bit value into its data register.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Link: https://lore.kernel.org/r/839f475cc75c97ffb3496a4caa93de2faabdbca2.1645629688.git.michal.simek@xilinx.com
In the workaround added with 'commit b6f44082d5 ("mmc: zynq_sdhci: Wait
till sd card detect state is stable")' the timeout variable has post
decrement. Whenever timeout happens, this post decrement is making
timeout=0xffffffff, so timeout error print and return statement are
never reached. Fix it by decrementing it inside the while loop.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/61fc1160ada0dd622cd29e381a74af7bf3d9a200.1645625609.git.michal.simek@xilinx.com
