Switch spi_flash_* interfaces to call into new SPI NOR framework via MTD
layer. Fix up sf_dataflash to work in legacy way. And update sandbox to
use new interfaces/definitions
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
Linux uses "jedec,spi-nor" as compatible string for JEDEC compatible
SPI Flash device nodes. Therefore make U-Boot also to look for the same
compatible string so that we can use Linux DTS files as is.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
For legacy reasons, we will have to keep around U-Boot specific
SPI_FLASH_BAR and SPI_TX_BYTE. Add them back to the new framework
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
Sync Serial Flash Discoverable Parameters (SFDP) parsing support from
Linux. This allows auto detection and configuration of Flash parameters.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
Sync changes from Linux SPI NOR framework to add 4 byte addressing
support. This is required in order to support flashes like MT35x
that no longer support legacy Bank Address Register(BAR) way of accessing
>16MB region.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
Many SPI controllers have special MMIO interfaces which provide
accelerated read/write access but require knowledge of flash parameters
to make use of it. Recent spi-mem layer provides a way to support such
controllers.
Therefore, add spi-mem support to spi-nor-core as a way to support SPI
controllers with MMIO interface. SPI MEM layer takes care of translating
spi_mem_ops to spi_xfer()s in case of legacy SPI controllers.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
Current U-Boot SPI NOR support (sf layer) is quite outdated as it does not
support 4 byte addressing opcodes, SFDP table parsing and different types of
quad mode enable sequences. Many newer flashes no longer support BANK
registers used by sf layer to a access >16MB of flash address space.
So, sync SPI NOR framework from Linux v4.19 that supports all the
above features. Start with basic sync up that brings in basic framework
subsequent commits will bring in more features.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
SPI flash based MTD devs can be registered/unregistered at any time
through the sf probe command or the spi_flash_free() function.
This commit does not try to fix the root cause as it would probably
require rewriting most of the code and have an mtd_info object
instance per spi_flash object (not to mention that the the spi-flash
layer is likely to be replaced by a spi-nor layer ported from Linux).
Instead, we try to be as safe as can be by checking the code returned
by del_mtd_device() and complain loudly when there's nothing we can
do about the deregistration failure. When that happens we also reset
sf_mtd_info.priv to NULL, and check for NULL pointer in the mtd hooks
so that -ENODEV is returned instead of hitting a NULL pointer
dereference exception when the MTD instance is later accessed by a user.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Heiko Schocher <hs@denx.de>
The DM implementation of spi_flash_free() does not unregister the MTD
device before removing the spi dev object. This leads to a use-after-free
bug when the MTD device is later accessed by a MTD user (observed when
attaching the device to UBI after env_sf_load() has called
spi_flash_free()).
Implement ->remove() and call spi_flash_mtd_unregister() from there.
Fixes: 9fe6d8716e ("mtd, spi: Add MTD layer driver")
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
spi_flash_mtd_register() can be called several times and each time it
will register the same mtd_info instance like if it was a new one.
The MTD ID allocation gets crazy when that happens, so let's track the
status of the sf_mtd_info object to avoid that.
Fixes: 9fe6d8716e ("mtd, spi: Add MTD layer driver")
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
It is useful to obtain the block-protect setting of the SPI flash, so we
know whether it is fully open or (perhaps partially) write-protected. Add
a method for this. Update the sandbox driver to process this operation and
add a test.
Signed-off-by: Simon Glass <sjg@chromium.org>
NOR flash name MT35X_QLKA and MT25Q_** used on NXP board has
manufacturer id as 0x2C, which are rather for newer flashes
after the split of Micron from ST.
So macro for this micron manufacturer id.
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
[jagan: updated commit message]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
When SPI flash operations fail it is helpful to be able to see the error
codes and where they are generated. Add logging to capture this
information for read operations.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present spi_flash_cmd_read_ops() allocates and frees a few bytes of
memory every time it is called. It is faster to use the stack for this
and this is now supported by the minimum GCC version required by U-Boot.
Remove the allocation and use a variable-sized array instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Now that we don't have to deal with the command-line flag we can simplify
the code for detecting the emulator. Remove the lookup based on the SPI
specification, relying just on the device tree to locate the emulator.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add logging to aid debugging features in these drivers. Also drop some
code in sandbox_spi_xfer() which is not used.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we support specifying SPI flash devices to use in the device
tree and on the command line. Drop the second option, since it is a pain
to support nicely with driver model, and unnecessary.
Signed-off-by: Simon Glass <sjg@chromium.org>
This patch adds support for 2 new XMC (Wuhan Xinxin Semiconductor
Manufacturing Corp) SPI NOR chips.
This support can be enabled by selecting the SPI_FLASH_XMC Kconfig
option.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Add support for SPANSION s25fl128l
Signed-off-by: Clément Laigle <c.laigle@catie.fr>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
[jagan: fixed , at the end of } ]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
This commit adds paired dev info for winbond w25q16jv
(tested w25q16jvssiq with a i.mx6 board)
Signed-off-by: Ludwig Zenz <lzenz@dh-electronics.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Add support for the Macronix mx25l1633e nor flash. (Tested on a imx6 board)
Signed-off-by: Ludwig Zenz <lzenz@dh-electronics.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Add support for the Gigadevice gd25q16c nor flash. (Tested on a imx6 board)
Signed-off-by: Ludwig Zenz <lzenz@dh-electronics.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This commit adds the following flashes to the id-table
- W25Q16JV
- W25Q32JV
- W25Q64JV
- W25Q128JV
- W25Q256JV
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The N25Q256(A) datasheet clearly states that this device does have
a Flag Status Register and does update FSR PEC bit 7 during Program
and Erase cycles to indicate the cycle is in progress. Enable the
FSR PEC bit polling on this device to prevent data corruption.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jagan Teki <jagan@openedev.com>
Cc: Tom Rini <trini@konsulko.com>
Move the strdup() call so that it is only done when we know we will bind
the device.
Reported-by: Coverity (CID: 131216)
Signed-off-by: Simon Glass <sjg@chromium.org>
This flash IC is used in some chromebook models
manufactured by Bitland.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The clean_bar() function resets the SPI NOR BAR register to 0, but
does not set the flash->curr_bar to 0 , therefore those two can get
out of sync, which could ultimatelly result in corrupted flash content.
The simplest test case is this:
=> mw 0x10000000 0x1234abcd 0x4000
=> sf probe
=> sf erase 0x1000000 0x10000
=> sf write 0x10000000 0x1000000 0x10000
=> sf probe ; sf read 0x12000000 0 0x10000 ; md 0x12000000
That is, erase a sector above the 16 MiB boundary and write it with
random pre-configured data. What will actually happen without this
patch is the sector will be erased, but the data will be written to
BAR 0 offset 0x0 in the flash.
This is because the erase command will call write_bar()+clean_bar(),
which will leave flash->bank_curr = 1 while the hardware BAR registers
will be set to 0 through clean_bar(). The subsequent write will also
trigger write_bar()+clean_bar(), but write_bar checks if the target
bank == flash->bank_curr and if so, does NOT reconfigure the BAR in
the SPI NOR. Since flash->bank_curr is still 1 and out of sync with
the HW, the condition matches, BAR programming is skipped and write
ends up at address 0x0, thus corrupting flash content.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Added support for is25wp032, is25wp064 and is25wp128.
Signed-off-by: Kimmo Rautkoski <ext-kimmo.rautkoski@vaisala.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
We have a large number of places where while we historically referenced
gd in the code we no longer do, as well as cases where the code added
that line "just in case" during development and never dropped it.
Signed-off-by: Tom Rini <trini@konsulko.com>
This commit adds support for the SST sst26wf016, sst26wf032
and sst26wf064 flash IC.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
sst26wf flash series block protection implementation differs
from other SST series, so add specific implementation
flash_lock/flash_unlock/flash_is_locked functions for sst26wf
flash ICs.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Make sure the user is notified instead of silently returning an error.
Signed-off-by: Liam Beguin <liambeguin@gmail.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
This SUNXI variant SPL SPI code doesn't use either SPI or
SPL_FLASG subsystems due to size constraints and also placing
this code in drivers/mtd/spi will unnecessary build SPI_FLASH
code(if defined) which never required, hence moved to arch area.
And also renamed the file according to kconfig which resembles
proper name.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Thomas reported U-Boot failed to build host tools if libfdt-devel
package is installed because tools include libfdt headers from
/usr/include/ instead of using internal ones.
This commit moves the header code:
include/libfdt.h -> include/linux/libfdt.h
include/libfdt_env.h -> include/linux/libfdt_env.h
and replaces include directives:
#include <libfdt.h> -> #include <linux/libfdt.h>
#include <libfdt_env.h> -> #include <linux/libfdt_env.h>
Reported-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
spi_flash_probe_tail is now only called from spi_flash_probe, hence we
can merge its body into spi_flash_probe.
Reviewed-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Commit ba45756 ("dm: x86: spi: Convert ICH SPI driver to driver model")
removed the last usage of the spi_flash_probe_fdt function, rendering it
obsolete.
This patch removes the function.
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Command bytes are part of the written bytes and they should be taken into
account when sending a spi transfer.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
For some SPI controllers it's not possible to keep the CS active between
transfers and they are limited to a known number of bytes.
This splits spi_flash reads into different iterations in order to respect
the SPI controller limits.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This spi-nor is 4Mbit/512KB
Fixes: b4fbcbc5a5 ("mtd/spi: add support for is25lq040b")
Signed-off-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The Allwinner SPI flash SPL boot support is guarded by the SPL_SPI_SUNXI
symbol. But despite its generic name, the actual only use case for this
is to provide SPI flash support to the SPL, which requires
CONFIG_SPL_SPI_FLASH_SUPPORT to be defined.
Select this symbol from the SPL_SPI_SUNXI Kconfig definition. This
avoids doing this explicitly in the defconfig, and fixes SPI booting on
the Pine64 SoPine (and -LTS version) and the OrangePi Win board (both with
SPI flash).
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The content of Bank Address Register (BAR) is volatile. It is cleared
after power cycle or reset command (RESET F0h).
Some memories (like e.g. s25fl256s) use it to access memory larger than
0x1000000 (16 MiB).
The problem shows up when one:
1. Reads/writes/erases memory > 16 MiB
2. Calls "reset" u-boot command (which is not causing BAR to be cleared)
In the above scenario, the SoC ROM sends 0x000000 address to read SPL.
Unfortunately, the BA24 bit is still set and hence it receives content
from 0x1000000 (16 MiB) memory address.
As a result the SoC aborts and we hang. Only power cycle can take the
SoC out of this state.
How to reproduce/test:
sf probe; sf erase 0x1200000 0x800000; reset
sf probe; sf erase 0x1200000 0x800000; sf write 0x11000000 0x1200000 0x800000; reset
sf probe; sf read 0x11000000 0x1200000 0x800000; reset
Signed-off-by: Lukasz Majewski <lukma@denx.de>
[Fixed comment text on clean_bar function]
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The sunxi-specific SPI load routine only knows how to load a legacy
U-Boot image.
Teach it how to handle FIT images as well, simply by providing the
existing SPL FIT loader with the right loader routine to access the SPI
NOR flash.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reported-by: Peter Kosa <kope@madnet.sk>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Spansion S25FS256S and S25FL256S flashes have equal JEDEC ID and ext ID.
As far as S25FL256S occures in spi_flash_ids before S25FS256S, U-Boot
incorrectly detects FS flash as FL. Thus its better to compare with
S25FS256S first.
Signed-off-by: Vsevolod Gribov <vgribov@larch-networks.com>
[Added S-o-b]
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The flash chip is 2 MiB , organized as 32 x 64 kiB sectors .
Rectify the entry to match the datasheet, reality and Linux SNOR IDs.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Add MT35XU512ABA1G12 parameters to NOR flash parameters array.
The MT35XU512ABA1G12 only supports 1 bit mode and 8 bits. It can't support
dual and quad. Supports subsector erase with 4KB granularity, have support
of FSR(flag status register) and flash size is 64MB.
Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
On some flash (like Macronix), QE (quad enable) bit is in the same
status register as BP# bits, and we need preserve its original value
during a reboot cycle as this is required by some platforms (like
Intel ICH SPI controller working under descriptor mode).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
[Refined code for readability]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add the print message to tell us why the erase operation doesn't work.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This adds support for Macronix flash MX25U6435F (device ID 0xc22537).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Move the only use of CONFIG_SF_DUAL_FLASH to defconfig. This makes the
associated topic_miamiplus.h header obsolete, so remove that as well.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The Allwinner H5 is very close to the H3 SoC, but has ARMv8 cores.
To allow sharing the clocks, GPIO and driver code easily, create an
architecture agnostic MACH_SUNXI_H3_H5 Kconfig symbol.
Rename the existing symbol to MACH_SUNXI_H3_H5 where code is shared and
let it be selected by a new shared Kconfig option.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Addresses passed on to readl and writel are expected to be of the same
size as a pointer. Change the parameter types of sunxi_spi0_read_data()
to make the compiler happy and allow a warning-free aarch64 compile.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This patch adds the flags parameter to device_remove() and changes all
calls to this function to provide the default value of DM_REMOVE_NORMAL
for "normal" device removal.
This is in preparation for the driver specific pre-OS (e.g. DMA
cancelling) remove support.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
At present devices use a simple integer offset to record the device tree
node associated with the device. In preparation for supporting a live
device tree, which uses a node pointer instead, refactor existing code to
access this field through an inline function.
Signed-off-by: Simon Glass <sjg@chromium.org>
This reverts commit c56ae7519f.
Once the 'Quad Enable' bit is cleared in their Enhanced Volatile
Configuration Register (EVCR), Micron memories expect ALL commands to use
the SPI 4-4-4 protocol. Commands using SPI 1-y-z protocols are no longer
accepted.
Within the reverted commit, the write_evcr() function is implemented using
the spi_flash_write_common(), which is a shortcut for the
[ spi_flash_cmd_write_enable(), spi_flash_cmd_write(),
spi_flash_cmd_wait_ready() ] sequence.
Since the internal state of the Micron memory has been changed when the
spi_flash_cmd_write() function completes, the later call of the
spi_flash_cmd_wait_ready() function fails.
Indeed the SPI controller driver is not aware of the SPI protocol switch.
Further patches will fix the support of Micron QSPI memories.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
[Rebase on master, use JEDEC_MFR(info) in place of idcode0]
Signed-off-by: Jagan Teki <jagan@openedev.com>
As long as the memory mapped size specifeid in the DT is the same or
bigger than the device size, it will work. So do not force the sizes
to be identical.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
In spi_flash_scan, 'ret' is initialled to -1, but 'ret' is not always
used to store a return value, in that case, even when the function
succeed, an error (-1) will be returned.
Lets just return 0 if we hit the end of the function.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
It is useful to name each method so that we can print out this name when
using the method. Currently this happens using a separate function. In
preparation for unifying this, add a name to each method.
The name is only available if we have libcommon support (i.e can use
printf()).
Signed-off-by: Simon Glass <sjg@chromium.org>
Some boards may want to use these subsystems with of-platdata in SPL. Add
support for this by avoiding any device tree access in this case.
Signed-off-by: Simon Glass <sjg@chromium.org>
This commit adds support for the Macronix MX66U51235F,
MX66L1G45G and Micron MT25QU02G, MT25QL02G flash parts.
Signed-off-by: Radu Bacrau <dumitru.bacrau@intel.com>
Cc: Chin Liang See <clsee@altera.com>
Cc: Radu Bacrau <radu.bacrau@gmail.com>
[Update proper commit header and 80-line cut on body]
Reviewed-by: Jagan Teki <jagan@openedev.com>
Somehow an int returning function without a return statement sneaked
in, fix it.
Also fix some whitespace damage on the way.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
s25fs512s and s25fl512s_256k have common id information
till 5 bytes and 6th byte have different family id
like FS and FL-S as 0x81 and 0x80.
Reported-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
- fix single line comments
- remove unneeded spaces
- ascending order of include files
- rename SPI DATAFLASH to dataflash
- rename SPI DataFlash to dataflash
- return NULL replaced with error code
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This patch fixed the add_dataflash return logic,
so-that it can handle both jedec and older chips
same as Linux.
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Flash id detection should be the first step to enumerate
the connected flash on the board, once ie done checking
with respective id codes locally in the driver all this
should be part of jedec_probe instead of id detection and
validated through flash_info{} table separatly.
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
dataflash doesn't require options, memory_map from spi.
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: York Sun <york.sun@nxp.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Dual flash code in spi are usually take the spi controller
to work with dual connected flash devices. Usually these
dual connection operation's are referred to flash controller
protocol rather with spi controller protocol, these are still
present in flash side for the usage of spi-nor controllers.
So, this patch remove the dual_flash options or flags in sf
which are triggered from spi controller side.
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
spi_flash_write_bar-> write_bar
spi_flash_write_bar -> read_bar
spi_flash_cmd_wait_ready -> spi_flash_wait_till_ready
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Use small 'd' in s25s512s ext_jedec
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
For readability use small letter's with flash name.
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Now the flash params table as renamed to spi_flash_ids structure,
so rename the sf_params.c to spi_flash_ids.c and remove the legacy.
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Remove unneeded/non-meaningful commit message on
params and flash.
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
In spansion S25FS-S family the physical sectors are grouped as
normal and parameter sectors. Parameter sectors are 4kB in size
with 8 set located at the bottom or top address of a device.
Normal sectors are similar to other flash family with sizes of
64kB or 32 kB.
To erase whole flash using sector erase(D8h or DCh) won't effect
the parameter sectors, so in order to erase these we must use 4K
sector erase commands (20h or 21h) separately.
So better to erase the whole flash using 4K sector erase instead
of detecting these family parts again and do two different erase
operations.
For this:
- Removed spansion_s25fss_disable_4KB_erase code
- Add SECT_4K for S25FS512S chip
Cc: Yunhui Cui <yunhui.cui@nxp.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
Add Spansion S25FS256S_64K spi flash to the list of spi_flash_ids.
In spansion S25FS-S family the physical sectors are grouped as
normal and parameter sectors. Parameter sectors are 4kB in size
with 8 set located at the bottom or top address of a device.
Normal sectors are similar to other flash family with sizes of
64kB or 32 kB.
To erase whole flash using sector erase(D8h or DCh) won't effect
the parameter sectors, so in order to erase these we must use 4K
sector erase commands (20h or 21h) separately.
So better to erase the whole flash using 4K sector erase instead
of detecting these family parts again and do two different erase
operations.
Cc: Yunhui Cui <yunhui.cui@nxp.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
INFO6 is for tabulating 6 byte flash parts, Ex: S25FS256S_64K
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
So, now SPI_FLASH_ID_MAX_LEN is 6 bytes useful for
few spansion flash families S25FS-S
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Add id length of 5 bytes numerical value to macro.
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
Rename nr_sectors as n_sectors to sync with Linux.
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
- Proper tabs spaces
- Removed unnecessary
- Add comments in spi_flash_info members
- Add comments for spi_flash_info.flags
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Instead of extracting id's separately better
to use JEDEC_MFR|ID for code simplicity.
Cc: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
Simplify the flash_lock ops detection code and added
meaningful comment.
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
INFO macro make flash table entries more adjustable like
adding new flash_info attributes, update ID length bytes
and so on and more over it will sync to Linux way of defining
flash_info attributes.
- Add JEDEC_ID
- Add JEDEC_EXT macro
- Add JEDEC_MFR
- spi_flash_params => spi_flash_info
- params => info
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Update the ext loader to avoid using the spl_image global variable.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
At present there are two SPI functions only used by freescale which are
defined in the spi_flash.h header. One function name matches an existing
generic SPL function.
Move these into a private header to avoid confusion.
Arcturus looks like it does not actually support SPI, so drop the SPI code
from that board.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a linker list declaration for this method and remove the explicit
switch() code. Also set up the sunxi function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
All the other SPL loaders are in this directory, so move the SPI one in
there too.
There are two board-specific SPI loaders (fsl and sunxi). These remain in
the drivers/mtd/spi directory, since they do not contain generic code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
At present some spl_xxx_load_image() functions take a parameter and some
don't. Of those that do, most take an integer but one takes a string.
Convert this parameter into a struct so that we can pass all functions the
same thing. This will allow us to use a common function signature.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Instead of using the global spl_image variable, pass the required struct in
as an argument.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Now, arch/${ARCH}/include/asm/errno.h and include/linux/errno.h have
the same content. (both just wrap <asm-generic/errno.h>)
Replace all include directives for <asm/errno.h> with <linux/errno.h>.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Fixup include/clk.]
Signed-off-by: Tom Rini <trini@konsulko.com>
This patch moves flags macro's to respective member position on
spi_flash_params{}, for better readabilty and finding the
respective member macro's easily.
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Add CONFIG_SPI_FLASH_USE_4K_SECTORS in spi_flash code from header file.
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
SECT_32K never used anywhere in the code.
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Make rx mode flags as generic to spi, earlier mode_rx is
maintained separately because of some flash specific code.
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
e_rd_cmd is maintained separately for fastest read command code,
since the read commands are computed normally this e_rd_cmd
is not required in spi_flash_params table.
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Fastest read command code look for fastest read command
taking inputs from spi->mode_rx and flags from param table
and controller mode_rx is always been a priority.
Since mode_rx is always set from controller side this optimized
code doesn't require much and this code required exctra overhead like
1) Maintain e_rx_cmd in param table
2) Maintain mode_rx in spi_slave {}
Hence removed this code, and look for read command from normal
spi->mode from spi_slave{} and params->flags
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
This commit adds support in the spi-nor driver for the
N25Q016A, a 16Mbit SPI NOR flash from Micron.
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Allwinner devices support SPI flash as one of the possible
bootable media type. The SPI flash chip needs to be connected
to SPI0 pins (port C) to make this work. More information is
available at:
https://linux-sunxi.org/Bootable_SPI_flash
This patch adds the initial support for booting from SPI flash.
The existing SPI frameworks are not used in order to reduce the
SPL code size. Right now the SPL size grows by ~370 bytes when
CONFIG_SPL_SPI_SUNXI option is enabled.
While there are no popular Allwinner devices with SPI flash at
the moment, testing can be done using a SPI flash module (it
can be bought for ~2$ on ebay) and jumper wires with the boards,
which expose relevant pins on the expansion header. The SPI flash
chips themselves are very cheap (some prices are even listed as
low as 4 cents) and should not cost much if somebody decides to
design a development board with an SPI flash chip soldered on
the PCB.
Another nice feature of the SPI flash is that it can be safely
accessed in a device-independent way (since we know that the
boot ROM is already probing these pins during the boot time).
And if, for example, Olimex boards opted to use SPI flash instead
of EEPROM, then they would have been able to have U-Boot installed
in the SPI flash now and boot the rest of the system from the SATA
hard drive. Hopefully we may see new interesting Allwinner based
development boards in the future, now that the software support
for the SPI flash is in a better shape :-)
Testing can be done by enabling the CONFIG_SPL_SPI_SUNXI option
in a board defconfig, then building U-Boot and finally flashing
the resulting u-boot-sunxi-with-spl.bin binary over USB OTG with
a help of the sunxi-fel tool:
sunxi-fel spiflash-write 0 u-boot-sunxi-with-spl.bin
The device needs to be switched into FEL (USB recovery) mode first.
The most suitable boards for testing are Orange Pi PC and Pine64.
Because these boards are cheap, have no built-in NAND/eMMC and
expose SPI0 pins on the Raspberry Pi compatible expansion header.
The A13-OLinuXino-Micro board also can be used.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Serial number, vendor id and page size are added for QSPI flash
common on both LS1012AQDS and LS1012ARDB i.e. S25FS512SDSMFI011.
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@nxp.com>
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Detect a FIT when loading from SPI and handle it using the
new FIT SPL support.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The S25FS-S family physical sectors may be configured as a hybrid
combination of eight 4-kB parameter sectors at the top or bottom
of the address space with all but one of the remaining sectors
being uniform size.
The default status of the flash is in this hybrid architecture.
The parameter sectors and the uniform sectors have different erase
commands.
This patch disable the hybrid sector architecture then the flash will
has uniform sector size and uniform erase command.
This configuration is temporary, the flash will revert to hybrid
architecture after power on reset.
Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The flash type of LS2085AQDS QSPI is S25FS256S. It has special write
any device register command and read any device register command.
This patch enable support for those commands.
Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Allow the spl_parse_image_header() to return value. This is convenient
for controlling the SPL boot flow if the loaded image is corrupted.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <van.freenix@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@konsulko.com>
get_timer() returns an unsigned 64-bit value, but is currently assigned to
a signed 32-bit variable. Due to sign extension and data truncation, this
causes the timeout loop in spi_flash_cmd_wait_ready() to immediately (and
incorrectly) fire for about 50% of all time values, based on whether bit
31 is set. In sandbox at least, this causes the test to pass or fail based
on system uptime, as opposed to time since the U-Boot binary was started.
Fixes: 4efad20a17 ("sf: Update status reg check in spi_flash_cmd_wait_ready")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
The stm_is_locked_sr() function is picked from Linux kernel. For reason
unknown, the 64bit data types used by the function and present in Linux
were replaced with 32bit unsigned ones, which causes trouble.
The testcase performed was done using ST M25P80 chip.
The command used was:
=> sf protect unlock 0 0x10000
The call chain starts in stm_unlock(), which calls stm_is_locked_sr()
with negative ofs argument. This works fine in Linux, where the "ofs"
is loff_t, which is signed long long, while this fails in U-Boot, where
"ofs" is u32 (unsigned int). Because of this signedness problem, the
expression past the return statement to be incorrectly evaluated to 1,
which in turn propagates back to stm_unlock() and results in -EINVAL.
The correction is very simple, just use the correctly sized data types
with correct signedness in the function to make it work as intended.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
When an error number is provided we should use it, not change it. This fixes
the SPI and SPI flash tests.
One of these is long-standing. The other seems to have been introduced by
commit 1e90d9fd (sf: Move read_id code to sf_ops).
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes: 1e90d9fd (sf: Move read_id code to sf_ops)
Reviewed-by: Jagan Teki <jteki@openedev.com>
Tested-by: Jagan Teki <jteki@openedev.com>
We must not free data that is managed by driver mode. Remove this line,
which is a hangover from the pre-driver-model code.
This fixes a problem where 'sf probe' crashes U-Boot if the backing file
for the SPI flash cannot be found.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Tested-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a little more debugging to help when things go wrong.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Tested-by: Jagan Teki <jteki@openedev.com>
Add dma memcpy api to the default spi_flash_copy_mmap(), so that
dma will be used to copy data when CONFIG_DMA is defined for the
platform.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
This function currently searches the entire device tree for a node that
it thinks is relevant. But the node is known and is passed in. Correct the
code and enable it only with driver model, since only driver-model boards
will use it.
This avoids bringing in a large number of strings from fdtdec.
Signed-off-by: Simon Glass <sjg@chromium.org>
For SPL we don't really need sprintf() and with tiny-printf this is not
available. Allow this to be dropped in SPL when using tiny-printf.
Signed-off-by: Simon Glass <sjg@chromium.org>
Since spi rx mode macro's are renamed to simple and
meaninfull, this patch will rename the respective
structure members.
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Tested-by: Jagan Teki <jteki@openedev.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
While setting quad bit on spansion, macronix code
is writing only particular quad bit this may give
wrong functionality with other register bits,
So this patch fix the issue where it with write
previous read reg status along particular quad bit.
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
One macronix quad bit set using SR, it's good to
read back and check the written bit and also if
it's already been set check for the bit and return.
Cc: Vignesh R <vigneshr@ti.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
One spansion quad bit set using CR, it's good to
read back and check the written bit and also if
it's already been set check for the bit and return.
Cc: Vignesh R <vigneshr@ti.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Setting up quad bit for micron devices need to do the
same way as other flash devices like spansion, winbond
etc does using enhanced volatile config register so this
patch adds this support instead of printing "QEB is volatile"
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Peter Pan <peterpandong@micron.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
- Tab space
- Place all read commands at one place.
- Re-arrange write commands.
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Use direct call to device_remove instead of exctra
spi_flash_remove defination.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
bar_end gives more meaningfull compared to bank_end and
spi_flash_write_bar uses bar_end so replaced bank_end with
bar_end in spi_flash_read_bar
Signed-off-by: Jagan Teki <jteki@openedev.com>
Since spi_read_cmds_array is used locally in
spi_flash_scan, so move array to locally used
function instead of defining global array.
Tested-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Since SPI_TX_* are spi_slave{} members so use spi protocol
notation instead spi flash programming, like
SPI_TX_BP => SPI_TX_BYTE
SPI_TX_QPP => SPI_TX_QUAD
Cc: Simon Glass <sjg@chromium.org>
Tested-by: Jagan Teki <jteki@openedev.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Used mode member from spi_slave{} instead of op_mode_tx.
Cc: Simon Glass <sjg@chromium.org>
Tested-by: Jagan Teki <jteki@openedev.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
For better code readabilty, get the spi pointer from
spi_flash{} locally and use it instead of direct
dereferring spi pinter as flash->spi->*
Tested-by: Jagan Teki <jteki@openedev.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Since all spi-flash core operations are moved into
sf_ops.c then it's better to renamed as spi-flash.c
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Used static for file-scope functions in sf_probe.c
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Since spi_slave is a spi pointer in spi_flash{} then assign
spi_slave{} pointer to flash->spi and remove spi_slave
pointer argument to
- spi_flash_probe_slave
- spi_flash_scan
Tested-by: Jagan Teki <jteki@openedev.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
For assigning read_bar commands in spansion case, break
is missing this patch add that break.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
SST parts added on sf_params.c supports both SST_WR which consits
of both BP and WP and there is a spi controller ich which supports
only BP so the relevent _write hook set based on "slave->op_mode_tx"
hence there is no respective change required from flash side hance
removed these.
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Removed unneeded header includes in sf_ops and sf_probe
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Using macro's for flash power up read-only access code
leads wrong behaviour hence use idcode0 for runtime
detection, hence the flash which require this functionality
gets detected at runtime.
Tested-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Most of the register access function are static,
so used simple name to represent each.
Tested-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
This patch removes unneeded ifdef and fixed accordingly.
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Use static for file-scope functions and removed
them from header files.
Tested-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
- Move bar read code below the bar write hance both
at once place, hence it easy for #ifdef macro only
once and readable.
- Move read_cmd_array at top
Tested-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
read_id code is related to spi_flash stuff
hence moved to sf_ops.
Tested-by: Jagan Teki <jteki@openedev.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Intension is that sf_ops should deals all spi_flash
related stuff and sf_probe (which should renamed future)
should be an interface layer for spi_flash versus spi drivers.
sf_ops => spi_flash interface
sf_probe => interface layer vs spi_flash(sf_probe) to spi drivers
Tested-by: Jagan Teki <jteki@openedev.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Rename spi_flash_validate_params to spi_flash_scan
as this code not only deals with params setup but
also configure all spi_flash attributes.
And also moved all flash related code into
spi_flash_scan for future functionality addition.
Tested-by: Jagan Teki <jteki@openedev.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
It is follow up patch based on
"dm: Add support for all targets which requires MANUAL_RELOC"
(sha1: 484fdf5ba0)
to update function pointers for DM.
Using post_bind is not ideal but it is one on current option what can be
used. Variable reloc_done has to be used do not call relocation after
every bind. Maybe new core functions should be introduced for this case.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Make spl_*_load_image() functions return a value instead of
hanging if a problem is encountered. This enables main spl code
to make the decision whether to hang or not, thus preparing
it to support alternative boot devices.
Some boot devices (namely nand and spi) do not hang on error.
Instead, they return normally and SPL proceeds to boot the
contents of the load address. This is considered a bug and
is rectified by hanging on error for these devices as well.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Ian Campbell <ijc@hellion.org.uk>
Cc: Hans De Goede <hdegoede@redhat.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Jagan Teki <jteki@openedev.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
flash->flags for SST flash should be updated for both DM and non-DM
flash drivers.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
We should check the return value from spi_flash_cmd_read_status() and
propagate it in the case of error.
This fixes a defect caught by Coverity.
Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
SST SPI NOR flash has the same locking programming bits
as ST Micro - added support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
[Minor change on commit message]
Signed-off-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
The relevent boards which used this driver got zapped
in previous release and the driver is never used in the
code and also it doesn't use/do any spi-flash operations.
Commit details for relevent removed boards:
"ARM: at91: remove non-generic boards"
(sha1: f6b42c1403)
Cc: Tom Rini <trini@konsulko.com>
Cc: Albin Tonnerre <albin.tonnerre@free-electrons.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
commit c3c016c "sf: Add SPI NOR protection mechanism" introduced
flash_lock()/flash_unlock()/flash_is_locked() methods for SPI flash,
but not every flash driver supplies these. We should test these
methods against NULL before actually calling them.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Many SPI flashes have protection bits (BP2, BP1 and BP0) in the
status register that can protect selected regions of the SPI NOR.
Take these bits into account when performing erase operations,
making sure that the protected areas are skipped.
Tested on a mx6qsabresd:
=> sf probe
SF: Detected M25P32 with page size 256 Bytes, erase size 64 KiB, total 4 MiB
=> sf protect lock 0x3f0000 0x10000
=> sf erase 0x3f0000 0x10000
offset 0x3f0000 is protected and cannot be erased
SF: 65536 bytes @ 0x3f0000 Erased: ERROR
=> sf protect unlock 0x3f0000 0x10000
=> sf erase 0x3f0000 0x10000
SF: 65536 bytes @ 0x3f0000 Erased: OK
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
[re-worked to fit the lock common to dm and non-dm]
Signed-off-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Add the SPI NOR protection mechanism from the kernel.
This code is based on the work from
Brian Norris <computersforpeace@gmail.com>
Here is the commit details:
"mtd: spi-nor: refactor block protection functions"
(sha1: 62593cf40b23b523b9fc9334ca61ba6c595ebb09)
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
This patch adds flag status register reading support to
spi_flash_cmd_wait_ready.
Cc: Simon Glass <sjg@chromium.org>
Cc: Marek Vasut <marex@denx.de>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Hou Zhiqiang <B48286@freescale.com>
Tested-by: Jagan Teki <jteki@openedev.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Current flash wait_ready logic is not modular to add new
register status check, hence updated the status check for
adding few more register checks in future.
Below are the sf speed runs with 'sf update' on whole flash, 16MiB.
=> sf update 0x100 0x0 0x1000000
device 0 whole chip
16777216 bytes written, 0 bytes skipped in 59.564s, speed 289262 B/s
=> sf update 0x100 0x0 0x1000000
device 0 whole chip
16777216 bytes written, 0 bytes skipped in 62.549s, speed 275036 B/s
=> sf update 0x100 0x0 0x1000000
device 0 whole chip
16777216 bytes written, 0 bytes skipped in 61.276s, speed 284359 B/s
Cc: Simon Glass <sjg@chromium.org>
Cc: Marek Vasut <marex@denx.de>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Tom Rini <trini@konsulko.com>
Tested-by: Jagan Teki <jteki@openedev.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Use the flash->flags for generic usage, not only for dm-spi-flash,
this will be used for future flag additions.
[Correct the spi flash flags detect logic]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Optimized spi-flash bar writing code and also removed
unnecessary bank_sel in read_ops.
Cc: Simon Glass <sjg@chromium.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Add spi_flash_read_bar function for reading bar and
discovering bar commands at probe time.
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
If computed bank_sel is same as flash->bank_curr which is
computed at probe time, then return the bank_sel instead of zero.
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Added support for IS25LP128 flash part.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Added support for IS25LP064 flash part.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Added support for IS25LP032 flash part.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
The current name is inconsistent with other driver model data access
functions. Rename it and fix up all users.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
AT26DF081A is the spi flash type of TWR-MEM(SCH-26248) card.
We can access the flash through DSPI2 on LS1021ATWR board.
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
We have flipped CONFIG_SPL_DISABLE_OF_CONTROL. We have cleansing
devices, $(SPL_) and CONFIG_IS_ENABLED(), so we are ready to clear
away the ugly logic in include/fdtdec.h:
#ifdef CONFIG_OF_CONTROL
# if defined(CONFIG_SPL_BUILD) && !defined(SPL_OF_CONTROL)
# define OF_CONTROL 0
# else
# define OF_CONTROL 1
# endif
#else
# define OF_CONTROL 0
#endif
Now CONFIG_IS_ENABLED(OF_CONTROL) is the substitute. It refers to
CONFIG_OF_CONTROL for U-boot proper and CONFIG_SPL_OF_CONTROL for
SPL.
Also, we no longer have to cancel CONFIG_OF_CONTROL in
include/config_uncmd_spl.h and scripts/Makefile.spl.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
When doing a memory mapped copy we may have DMA available and thus need
to have this copy abstracted so that the driver can do it, rather than a
simple memcpy.
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Make the support for 4K subpage I/O on a SPI NOR flash configurable.
A board which requires the SPI NOR to be accessed in larger 32KiB
or 64KiB pages can disable the 4K subpage support, but by default,
the support for 4K subpage I/O is enabled. The functionality of this
option is the same as CONFIG_MTD_SPI_NOR_USE_4K_SECTORS in Linux.
This is extremely useful in case one uses UBI on a SPI NOR flash.
UBI needs at least 15k EBs and can not work on a flash which uses
4k ones, so disabling the support for 4k subpages lets UBI work on
such flash.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Add kconfig options for various SPI flashes and use them in cm-fx6 defconfig.
Cc: Jagan Teki <jteki@openedev.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Added SPI_FLASH_DATAFLASH entry on Kconfig with help description.
data flash driver comes with good decription, hence moved the
same on to kconfig help decription.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Haikun Wang <haikun.wang@freescale.com>
Added SPI_FLASH_MTD entry on Kconfig with help description.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Acked-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Heiko Schocher <hs@denx.de>
Rename CONFIG_SF_DATAFLASH into CONFIG_SPI_FLASH_DATAFLASH
as it follows the naming convention same as remaining configs.
Signed-off-by: Jagan Teki <jteki@openedev.com>
sst25wf040b doesn't support Auto Address Increment Programming command.
Remove SST_WR flag.
Signed-off-by: Haikun Wang <B53464@freescale.com>
Tested-by: Haikun Wang <haikun.wang@freescale.com>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
Add MTD layer driver for spi, original patch from:
http://git.denx.de/?p=u-boot/u-boot-mips.git;a=commitdiff;h=bb246819cdc90493dd7089eaa51b9e639765cced
Changes from Heiko Schocher against this patch:
- Remove compile error if not defining CONFIG_SPI_FLASH_MTD:
LD drivers/mtd/spi/built-in.o
drivers/mtd/spi/sf_probe.o: In function `spi_flash_mtd_unregister':
/home/hs/abb/imx6/u-boot/drivers/mtd/spi/sf_internal.h:168: multiple definition of `spi_flash_mtd_unregister'
drivers/mtd/spi/sf_params.o:/home/hs/abb/imx6/u-boot/drivers/mtd/spi/sf_internal.h:168: first defined here
drivers/mtd/spi/sf_ops.o: In function `spi_flash_mtd_unregister':
/home/hs/abb/imx6/u-boot/drivers/mtd/spi/sf_internal.h:168: multiple definition of `spi_flash_mtd_unregister'
drivers/mtd/spi/sf_params.o:/home/hs/abb/imx6/u-boot/drivers/mtd/spi/sf_internal.h:168: first defined here
make[1]: *** [drivers/mtd/spi/built-in.o] Fehler 1
make: *** [drivers/mtd/spi] Fehler 2
- Add a README entry.
- Add correct writebufsize, to fit with Linux v3.14
MTD, UBI/UBIFS sync.
Note (From Jagan): For testing raw mtd parition erase/read/write operations
using cmd_sf, sf_mtd should be required to register the spi flash device to
MTD layer but the sf_mtd_info ops were not required until and unless if we
use any flash filesystem layer say for example UBI. Due to this the foot-print
got increased ~290bytes in non-UBI case here that should be acceptible.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Jagannadh Teki <jteki@openedev.com>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
Atmel DataFlash chips have commands different from common spi
flash commands.
Atmel DataFlash also have special page-size.
This driver add support for accessing Atmel DataFlash.
It is based on the Driver Model.
Example:
=> sf probe 1:0
SPI DataFlash: Detected AT45DB021B with page size 264 Bytes, erase size 264 Bytes, total 264 KiB, revision d
=> sf erase 0 42000
SF: 270336 bytes @ 0x0 Erased: OK
=> mw.l 82000000 45444342 20000
=> sf write 82000000 0 42000
SF: 270336 bytes @ 0x0 Written: OK
=> sf read 83000000 0 42000
SF: 270336 bytes @ 0x0 Read: OK
=> cmp.b 82000000 83000000 42000
Total of 270336 byte(s) were the same
Signed-off-by: Haikun Wang <haikun.wang@freescale.com>
Tested-by: Haikun Wang <haikun.wang@freescale.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Chakra Divi <cdivi@openedev.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
This printf() should have a newline at the end. Add it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Default name of spi flash like this "0:0", update it to "spi_flash@0:0".
Signed-off-by: Haikun Wang <haikun.wang@freescale.com>
Acked-by: Simon Glass <sjg@chromium.org>
Upto now flash sector_size is assigned from params which isn't
necessarily a sector size from vendor, so based on the SECT_*
flags from flash_params the erase_size will compute and it will
become the sector_size finally.
Bug report (from Bin Meng):
=> sf probe
SF: Detected SST25VF016B with page size 256 Bytes, erase size 4 KiB,
total 2 MiB, mapped at ffe00000
=> sf erase 0 +100
SF: 65536 bytes @ 0x0 Erased: OK
Signed-off-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Reported-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
With SPI flash moving to driver model, commit fbb0991 "dm: Convert
spi_flash_probe() and 'sf probe' to use driver model" ignored the
SST flash-specific write op (byte program & word program), which
actually broke the SST flash from wroking.
This commit makes SST flash work again under driver model, by adding
SST flash-specific handling in the spi_flash_std_write().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Add a new member 'flags' in struct spi_flash to store the flash flags
during spi_flash_validate_params().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
This reverts commit 562f8df18d.
Note: Even un-reverting this patch couldn't works as expected, based
on the latest testing from Heiko Schocher.
Signed-off-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Cc: Heiko Schocher <hs@denx.de>
Need to check value of spi_setup_slave and spi_setup_slave_fdt.
If their return value 'bus' is NULL, there is no need to pass it
to following spi_flash_probe_tail.
If 'bus' is null, the original function flow is as following:
spi_flash_probe
|->spi_setup_slave
|->spi_probe_bus_tail
|->spi_flash_probe_slave
|->spi_free_slave
Alougth check the pointer in spi_free_slave is ok, checking the return value
of spi_setup_slave and spi_setup_slave_fdt is better.
Before this fix:
"
=> sf probe 0:2
FSL_QSPI: Not a valid cs !
SF: Failed to set up slave
data abort
pc : [<fff66dcc>] lr : [<fff7628c>]
reloc pc : [<87814dcc>] lr : [<8782428c>]
sp : fdf4fcf0 ip : e630396c fp : fe0d0888
r10: fffa2538 r9 : fdf4feb8 r8 : 02625a00
r7 : 00000002 r6 : fff94ec0 r5 : 00000000 r4 : 9355553c
r3 : 1af0593c r2 : cb3fe030 r1 : fff94eb8 r0 : e59ff018
Flags: nZCv IRQs off FIQs off Mode SVC_32
Resetting CPU ...
"
After this fix:
"
=> sf probe 0:2
FSL_QSPI: Not a valid cs !
Failed to initialize SPI flash at 0:2
"
No data abort using this patch.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Poll both the Read status and Flag status registers
for sucessful erase and program operations for the
Micron devices with E_FSR flag set in params table.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
CONFIG_SPI does not exist in Kconfig in the first place, so the
dependency "depends on DM && SPI" is never met, i.e., DM_SPI_FLASH
can never be enabled (unless you ignore the dependency in an illegal
way. See below.)
Actually, some defconfigs such as socfpga_*_defconfig define
CONFIG_DM_SPI_FLASH=y, but it never appears in the .config file
because of this wrong dependency.
On the other hand, all the Tegra boards enable DM_SPI_FLASH because
config DM_SPI_FLASH
default y
silently ignores the dependency.
Unfortunately, this style of CONFIG definition is abused everywhere
in U-Boot, so we easily miss such a wrong dependency.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Simon Glass <sjg@chromium.org>
Permit use of a udevice to talk to SPI flash. Ultimately we would like
to retire the use of 'struct spi_flash' for this purpose, so create the
new API for those who want to move to it.
Signed-off-by: Simon Glass <sjg@chromium.org>
In the case where the arch defines a custom map_sysmem(), make sure that
including just mapmem.h is sufficient to have these functions as they
are when the arch does not override it.
Also split the non-arch specific functions out of common.h
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a convenience function to access the private data that a uclass stores
for each of its devices. Convert over most existing uses for consistency
and to provide an example for others.
Signed-off-by: Simon Glass <sjg@chromium.org>
Expand the help messages for each driver. Add missing Kconfig for I2C,
SPI flash and thermal.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
At present we go through various contortions to store the SPI slave's chip
select in its private data. This only exists when the slave is active so
must be set up when it is probed. Until the device is probed we don't
actually know what chip select it will appear on.
However, now that we can support per-child platform data, we can use that
instead. This allows us to set up the chip select when the child is bound,
and avoid the messy contortions.
Unfortunately this is a fairly large change and it seems to be difficult to
break it down further.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add the necessary flash entry for the Spansion S25FL164K
flash. Tested on Marvell 88F6218 based design.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Added S25FL116K flash and tested on Marvell 88F6281 based system.
Signed-off-by: Adnan Ali <adnan.ali@codethink.co.uk>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Add support for SST25WF040B-40I-SN flash.
Tested on T1024QDS board.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Removed ramtron driver since the EMK boards are
no longer been active, and these are the only boards
used this flash driver.
Commit details for EMK zap:
"ppc/arm: zap EMK boards"
(sha1: d58a9451e7)
Signed-off-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Cc: Reinhard Meyer <reinhard.meyer@emk-elektronik.de>
Enabled byte program support for sst flashes in sf.
Few controllers will only support BP, so this patch gives
a tx transfer flag to set the BP so-that sf will operate
on byte program transfer.
A new TX operation mode SPI_OPM_TX_BP is introduced for such SPI
controller to use byte program op for SST flash.
Signed-off-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Currently if SST flash advertises SST_WP flag in the params table
the word program command (ADh) with auto address increment will be
used for the flash write op. However some SPI controllers do not
support the word program command (like the Intel ICH 7), the byte
programm command (02h) has to be used.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
At present SECT_4K is the same as SST_WP so we cannot tell these apart. Fix
this so that the table in sf_params.c can be used correctly.
Reported-by: Jens Rottmann <Jens.Rottmann@adlinktech.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Few of the spi controllers are only supports array slow
read which is quite different behaviour compared to others.
So this fix on sf will correctly handle the slow read supported
controllers.
Signed-off-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
U-Boot has never cared about the type when we get max/min of two
values, but Linux Kernel does. This commit gets min, max, min3, max3
macros synced with the kernel introducing type checks.
Many of references of those macros must be fixed to suppress warnings.
We have two options:
- Use min, max, min3, max3 only when the arguments have the same type
(or add casts to the arguments)
- Use min_t/max_t instead with the appropriate type for the first
argument
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Pavel Machek <pavel@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
[trini: Fixup arch/blackfin/lib/string.c]
Signed-off-by: Tom Rini <trini@ti.com>
The SPI function does the same thing, so we may as well just use the new
generic function. The 'cs' parameter was not actually used, so can be
dropped.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Acked-by: Heiko Schocher <hs@denx.de>
This code was not updated when the chip select handling was adjusted. Fix
it to call the correct function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Acked-by: Heiko Schocher <hs@denx.de>
Convert sandbox's spi flash emulation driver to use driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
We want the SPI flash probing feature to operate as a standard driver.
Add a driver for the basic probing feature used by most boards. This
will be activated by device_probe() as with any other driver.
The 'sf probe' command currently keeps track of the SPI slave that it
last used. This doesn't work with driver model, since some other driver
or system may have probed the device and have access to it too. On the
other hand, if we try to probe a device twice the second probe is a nop
with driver model.
Fix this by searching for the matching device, removing it, and then
probing it again. This should work as expected regardless of other device
activity.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Add a driver model uclass for SPI flash which supports the common
operations (read, write, erase). Since we must keep support for the
non-dm interface, some modification of the spi_flash header is required.
CONFIG_DM_SPI_FLASH is used to enable driver model for SPI flash.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Adjust spi_flash_probe_slave() to return an error value instead of a
pointer so we get the correct error return.
Have the caller allocate memory for spi_flash to simplify error handling,
and also so that driver model can use its existing allocated memory.
Add a spi.h include in the sf_params file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Since spi_flash.h is supposed to be the public API for SPI flash, move
private things to sf_internal.h. Also tidy up a few comment nits.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Some files are using SPI functions but not explitly including the SPI
header file. Fix this, since driver model needs it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
At present sandbox has its own table of supported SPI flash chips. Now that
the SPI flash system is fully consolidated and has its own list, sandbox
should use that.
This enables us to expand the number of chips that sandbox supports.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Add ID for this Numonix / STMicro chip.
Tested on Marvell DB-78460-BP board.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Luka Perkov <luka@openwrt.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Currently, CONFIG_SPL_SPI_* #defines are used for controlling SPI boot in
SPL. These #defines do not allow the user to select SPI mode for the SPI flash
(there's no CONFIG_SPL_SPI_MODE, so the SPI mode is hardcoded in
spi_spl_load.c), and duplicate information already provided by
CONFIG_SF_DEFAULT_* #defines.
Kill CONFIG_SPL_SPI_*, and use CONFIG_SF_DEFAULT_* instead.
Cc: Tom Rini <trini@ti.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Vitaly Andrianov <vitalya@ti.com>
Cc: Lars Poeschel <poeschel@lemonage.de>
Cc: Bo Shen <voice.shen@atmel.com>
Cc: Hannes Petermaier <hannes.petermaier@br-automation.com>
Cc: Michal Simek <monstr@monstr.eu>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Add support for M25PE16 and M25PX16
Cc: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
The list is supposed to be terminated with a NULL name, but is not. If a
board probes a chip which does not appear in the table, U-Boot will crash
(at least on sandbox).
Signed-off-by: Simon Glass <sjg@chromium.org>
It's usually a common pattern to free() the memory that we allocated.
Implement this here to stop leaking memory.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
enable the W#/Vpp signal to disable writing to the status
register on ST MICRON flashes like the N25Q128 thorugh
the new config option CONFIG_SYS_SPI_ST_ENABLE_WP_PIN
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Currently, flash quad bit is set in "spi_flash_validate_params" and later
at the end in the same api, we write 0 to status register for few flashes,
thereby overriding the quad bit set. This fix moves the quad bit setting
outside this api in "spi_flash_probe_slave"
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Add support of loading image, binary for MMC and SPI during SPL boot.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
SPI driver perform its operation(read/write) on 64KB buffer chunk for data
greater than 64KB. This buffer chunk is allocated from system heap.
During SPL boot, 768KB of data is read from SPI flash.
Here, heap size may not be sufficient enough to full-fill 64KB buffer
requirement of SPI driver. So break down u-boot read operation at 8KB of chunk.
Also, fix a warning i.e. "unused variable buf" during CONFIG_FSL_CORENET
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The commit 6af8dc3ebc broke support for
S25FL032P and S25FL064P by carelessly removing the code handling special
page size for these two SPI NOR flashes and unifying the code under the
assumption that Extended JEDEC ID of 0x4d00 always implies 512b page size.
Add special case handling for these two SPI NOR flashes.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Squash the malloc()+memset() combo in favor of calloc().
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Acked-by: Marek Vasut <marex@denx.de>
Squash the malloc()+memset() combo in favor of calloc().
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Both of these chips have 256kB big sectors, thus the _256K suffix,
compared to their _64K counterparts, which have 64kB sectors. Also,
they have four times less sectors than their _64K counterparts.
Signed-off-by: Marek Vasut <marex@denx.de>
Tested-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Remove the flag SECT_4K for device N25Q128 as the 4K-byte
sub sector erase granularity is available only for top/bottom
8 sectors in some of the N25Q128 chips.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
