Add '\n' for debug msg.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Match the depth of indentation between #ifdef and #endif
for better readability.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add PCI IRQ routing information in the board device tree and enable
writing PIRQ routing table and MP table.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Intel Bayley Bay board is a BayTrail based board. Add this board
with existing baytrail fsp support.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
This commit adds the microcode blob for BayTrail-I B0 stepping,
CPUID signature 30671h.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
BayTrail FSP Gold4 release adds one UPD parameter to control IGD
enable/disable.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
On Intel BayTrail SoC, there is a legacy UART (I/O 0x3f8) integrated
into the SoC which is enabled by the FSP. Remove the smsc47x superio
initialization codes.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
We should not set up kernel screen_info when the vesa parameters are
insane, otherwise kernel will panic.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add a cpu1 node to the device tree and enable the MP initialization
on QEMU targets (i440fx and q35).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
When running SMP configuration on QEMU (tcg mode, no kvm), there is
a busy loop in start_aps(), calling udelay(), that waits for APs to
show up online. However, there is a chance that VCPU1 will be timeout
waiting, IOW the secondary VCPUs haven't started their execution yet.
This patch adds a 'pause' instruction in __udelay() only for QEMU
target, to give other VCPUs a chance to run. When QEMU sees the
'pause' instruction, it will yeild the execution to other CPUs.
Signed-off-by: Miao Yan <yanmiaobest@gmail.com>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
On some platforms pci devices behind bridge need to be probed (eg:
a pci uart on recent x86 chipset) before relocation. Remove such
limitation so that dm pci can be used before relocation.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
This patch replaces not existing addr_uboot environment variable by
loadaddr at get_uboot_net and burn_uboot_xxx commands. Otherwise these
commands are broken.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Define base address of both usb xhci controllers in lsch3 config
in the format (IMMR + offset) for LS2085A
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Define CONFIG_SYS_CACHELINE_SIZE for LS2085A which is required by
USB XHCI stack for alignment
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
By default the bstopre value has been set to 0x100, used to be 1/4
value of refint. Modern DDR has increased the refresh time. Adjust
to 1/4 of refresh interval dynamically. Individual board can still
override this value in board ddr file, or to use auto-precharge.
Signed-off-by: York Sun <yorksun@freescale.com>
HW coherency won't work properly for CAAM write transactions
if AWCACHE is left to default (POR) value - 4'b0001.
It has to be programmed to 4'b0010.
For platforms that have HW coherency support:
-PPC-based: the update has no effect; CAAM coherency already works
due to the IOMMU (PAMU) driver setting the correct memory coherency
attributes
-ARM-based: the update fixes cache coherency issues,
since IOMMU (SMMU) driver is not programmed to behave similar to PAMU
Fixes: b9eebfade9 ("fsl_sec: Add hardware accelerated SHA256 and SHA1")
Signed-off-by: Horia Geantă <horia.geanta@freescale.com>
Reviewed-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Acked-by: Ruchika Gupta<ruchika.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Use fdt_setprop_u32() instead of fdt_setprop().
Fixes: 0181937fa3 ("crypto/fsl: Add fixup for crypto node")
Signed-off-by: Horia Geantă <horia.geanta@freescale.com>
Reviewed-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Acked-by: Ruchika Gupta<ruchika.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The patch will initialize PCIe controller on EP mode
1. Setup bar:
bar0 32bit 4K for specific configuration
bar1 32bit 8K for MSIX
bar2 64bit 4K for descriptor of memory
bar4 64bit 1M for DMA memory test
2. Setup iATU:
iATU inbound 0-3 to map bar transaction to memory address
started at CONFIG_SYS_PCI_EP_MEMORY_BASE
iATU outbound 0 to map 4G memory space
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
PCIe extends device's configuration space to 4k and provides
extended capability. The patch adds function to find them.
The code is ported from Linux PCIe driver.
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: York Sun <yorksun@freescale.com>
MC firware version 8.0.0 contains new command flags. This patch
contains modifications in FLIB files to support the new command flags.
Signed-off-by: Itai Katz <itai.katz@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The sampling of the oscillator can be done in multiple modes for
generating the entropy value. By default, this is set to von
Neumann. This patch changes the sampling to raw data, since it
has been discovered that the generated entropy has a better
'quality'.
Signed-off-by: Alex Porosanu <alexandru.porosanu@freescale.com>
Acked-by: Ruchika Gupta<ruchika.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The entropy delay (the length in system clocks of each
entropy sample) for the RNG4 block of CAAM is dependent
on the frequency of the SoC. By elaborate methods, it
has been determined that a good starting value for all
platforms integrating the CAAM IP is 3200. Using a
higher value has additional benefit of speeding up
the process of instantiating the RNG, since the entropy
delay will be increased and instantiation of the RNG
state handles will be reattempted by the driver. If the
starting value is low, for certain platforms, this can
lead to a quite lengthy process.
This patch changes the starting value of the length of
the entropy sample to 3200 system clocks.
In addition to this change, the attempted entropy delay
values are now printed on the console upon initialization
of the RNG block.
Signed-off-by: Alex Porosanu <alexandru.porosanu@freescale.com>
Acked-by: Ruchika Gupta<ruchika.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The rtfrqmax & rtfrqmin set the bounds of the expected frequency of the
oscillator, when SEC runs at its maximum frequency. For certain platforms
(f.i. T2080), the oscillator is very fast and thus if the SEC runs at
a lower than normal frequency, the ring oscillator is incorrectly detected
as being out of bounds.
This patch effectively disables the maximum frequency check, by setting a
high enough maximum allowable frequency for the oscillator. The reasoning
behind this is that usually a broken oscillator will run too slow
(i.e. not run at all) rather than run too fast.
Signed-off-by: Alex Porosanu <alexandru.porosanu@freescale.com>
Acked-by: Ruchika Gupta<ruchika.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
To improve eTSEC performance on LS1021A Rev2.0,
snooping of all transmit frames from memory and
all transmit BD memory accesses in enabled.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
On LS1021A Rev2.0, OCRAM's security level needs to be changed to
non-secure access for SD boot. This patch will allow OCRAM
access permission as R/W in SPL.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Bootrom will put cpus into WFE state when boot cpu release cpus, so
target cpu cannot correctly go to spin state.
Add 'sev' to wakeup non-boot cpu that hold on bootrom space, let target
cpu can fall into u-boot spin table.
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Program the external regulator to switch off voltage in deep sleep.
Signed-off-by: Chenhui Zhao <chenhui.zhao@freescale.com>
Acked-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Acked-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Enable bootscript support in secure boot for establishing
chain of trust on LS1021atwr.
Signed-off-by: Gaurav Rana <gaurav.rana@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
strncpy is safer than strcpy, use it to instead of strcpy.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
when using printf, the parameter type need to be compatible
type, so transform them to compatible type
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
For ls1021a, Reserve secure code in to memory in case OCRAM
is needed by other usage.
Signed-off-by: Zhuoyu Zhang <Zhuoyu.Zhang@freescale.com>
Acked-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Fix:
undefined reference to `spi_flash_free'
undefined reference to `spi_flash_probe'
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Stefan Roese <sr@denx.de>
Cc: Markus Niebel <Markus.Niebel@tq-group.com>
Acked-by: Stefan Roese <sr@denx.de>
1. Define two structures mx6ul_iomux_ddr_regs and mx6ul_iomux_grp_regs.
2. Add a new function mx6ul_dram_iocfg to configure dram io.
3. Refactor MMDC1 macro, discard "#ifdef CONFIG_MX6SX". Since
only mmdc0 channel exists on i.MX6SX/UL, redefine MMDC1 macro support
runtime check, but not hardcoding #ifdef macros.
4. Introduce mx6ul-ddr.h, which includes the register address for DRAM
IO configuration.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
1.Update WDOG settings.
2.No need to gate/ungate all PFDs for i.MX6UL.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Ye.Li <B37916@freescale.com>
