The TI AM654 timer is compatible with the omap-timer implementation,
so add it to the compatible id list.
Signed-off-by: Sjoerd Simons <sjoerd@collabora.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Cc: Francesco Dolcini <francesco@dolcini.it>
Cc: Wadim Egorov <w.egorov@phytec.de>
Signed-off-by: Nishanth Menon <nm@ti.com>
Approved DT binding has the port mode register in the
"phys" property. Get it from there instead of the custom
"cpsw-phy-sel" property.
This will allow us to keep DT in sync with Linux.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Nishanth Menon <nm@ti.com>
The approved DT property for MAC efuse (ROM) address is
"ti,syscon-efuse".
Use that and drop custom property "mac_efuse".
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Nishanth Menon <nm@ti.com>
The binding represents the MDIO controller as a child device tree
node of the MAC device tree node.
The U-Boot driver mostly ignores that child device tree node and just
hardcodes the resources it uses to support both the MAC and MDIO in a
single driver.
However, some resources like pinctrl muxing states are thus ignored.
This has been a problem with some device trees that will put some
pinctrl states on the MDIO device tree node, like the SK-AM62 Device
Tree does.
Let's rework the driver a bit to create a dummy MDIO driver that we will
then get during our initialization to force the core to select the right
muxing.
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Acked-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Nishanth Menon <nm@ti.com>
The adin phy has extended registers that can be accessed using
adin_ext_read and adin_ext_write. These registers can be read directly
using the mdio command using readext and writext. For example:
=> mdio rx ethernet@428a0000 0xff23
Reading from bus ethernet@428a0000
PHY at address 0:
65315 - 0xe01
Signed-off-by: Nate Drude <nate.d@variscite.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Copy and tweak the required code from the linux kernel.
Only the KSZ9893 has been tested.
Signed-off-by: Karsten Wiese <karsten.wiese@protechna.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
drivers/core/device.c will call `device_free()` after xhci_register
already frees the private device data. This can cause a crash later
during the boot process, observed on aarch64 RPi4b as a synchronous
exception. All callers of xhci_register use priv_auto, so this won't
lead to memory leaks.
Signed-off-by: Richard Habeeb <richard.habeeb@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This watchdog driver applies to the following
mcf families:
- mcf52x2 (5271 5275 5282)
- mcf532x (5329 5373)
- mcf523x (5235)
Cpu's not listed for each family does not have WDT module.
Note, after some attempts testing by qemu on 5208 i
finally abandoned, watchdog seems not implemented properly.
The driver has been tested in a real M5282EVM.
Signed-off-by: Angelo Dureghello <angelo@kernel-space.org>
---
Changes for v2:
- remove unnecessary hardcoded timeouts
- remove unnecessary hw_watchdog_xxx stuff
- rewrite wdog module reg calculation
- using IS_ENABLED() where possible
Changes for v3:
- remove hardcoded 4s test
In some designs the MAX313xx RTC may need calibration to cope with
oscillator inaccuracies. Provide read8/write8 ops so that the registers
can be accessed. Because the driver covers a range of MAX313xx variants
no attempt is made to ensure the register is valid.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Commit 62649165cb ("lib: sparse: Make CHUNK_TYPE_RAW buffer aligned")
fixed cache alignment for systems with a D-CACHE.
However it introduced some performance regressions [1] on system
flashing huge images, such as Android.
On AM62x SK EVM, we also observe such performance penalty:
Sending sparse 'super' 1/2 (768793 KB) OKAY [ 23.954s]
Writing 'super' OKAY [ 75.926s]
Sending sparse 'super' 2/2 (629819 KB) OKAY [ 19.641s]
Writing 'super' OKAY [ 62.849s]
Finished. Total time: 182.474s
The reason for this is that we use an arbitrary small buffer
(info->blksz * 100) for transferring.
Fix it by using a bigger buffer (info->blksz * FASTBOOT_MAX_BLK_WRITE)
as suggested in the original's patch review [2].
With this patch, performance impact is mitigated:
Sending sparse 'super' 1/2 (768793 KB) OKAY [ 23.912s]
Writing 'super' OKAY [ 15.780s]
Sending sparse 'super' 2/2 (629819 KB) OKAY [ 19.581s]
Writing 'super' OKAY [ 17.192s]
Finished. Total time: 76.569s
[1] https://lore.kernel.org/r/20221118121323.4009193-1-gary.bisson@boundarydevices.com
[2] https://lore.kernel.org/r/all/43e4c17c-4483-ec8e-f843-9b4c5569bd18@seco.com/
Fixes: 62649165cb ("lib: sparse: Make CHUNK_TYPE_RAW buffer aligned")
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
This driver considers that a node with an empty label is the top.
But the led class has changed, if a label is not provided for a led,
the label is filed with the node name. So we update this driver
to use a wrapper to manage the top led node.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Sec proxy data buffer is 60 bytes with the last of the registers
indicating transmission completion. This however poses a bit of a
challenge.
The backing memory for sec_proxy is regular memory, and all sec proxy
does is to trigger a burst of all 60 bytes of data over to the target
thread backing ring accelerator. It doesn't do a memory scrub when
it moves data out in the burst. When we transmit multiple messages,
remnants of previous message is also transmitted which results in
some random data being set in TISCI fields of messages that have been
expanded forward.
The entire concept of backward compatibility hinges on the fact that
the unused message fields remain 0x0 allowing for 0x0 value to be
specially considered when backward compatibility of message extension
is done.
So, instead of just writing the completion register, we continue
to fill the message buffer up with 0x0 (note: for partial message
involving completion, we already do this).
This allows us to scale and introduce ABI changes back also work with
other boot stages that may have left data in the internal memory.
While at this, drop the unused accessor function.
Fixes: f9aa41023b ("mailbox: Introduce K3 Secure Proxy Driver")
Signed-off-by: Nishanth Menon <nm@ti.com>
This reverts commit d927d1a808, reversing
changes made to c07ad9520c.
These changes do not pass CI currently.
Signed-off-by: Tom Rini <trini@konsulko.com>
Emulate Secure World's FF-A ABIs and allow testing U-Boot FF-A support
Features of the sandbox FF-A support:
- Introduce an FF-A emulator
- Introduce an FF-A device driver for FF-A comms with emulated Secure World
- Provides test methods allowing to read the status of the inspected ABIs
The sandbox FF-A emulator supports only 64-bit direct messaging.
Signed-off-by: Abdellatif El Khlifi <abdellatif.elkhlifi@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Cc: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Cc: Jens Wiklander <jens.wiklander@linaro.org>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Provide armffa command showcasing the use of the U-Boot FF-A support
armffa is a command showcasing how to invoke FF-A operations.
This provides a guidance to the client developers on how to
call the FF-A bus interfaces. The command also allows to gather secure
partitions information and ping these partitions. The command is also
helpful in testing the communication with secure partitions.
For more details please refer to the command documentation [1].
[1]: doc/usage/cmd/armffa.rst
Signed-off-by: Abdellatif El Khlifi <abdellatif.elkhlifi@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Cc: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Cc: Jens Wiklander <jens.wiklander@linaro.org>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add Arm FF-A support implementing Arm Firmware Framework for Armv8-A v1.0
The Firmware Framework for Arm A-profile processors (FF-A v1.0) [1]
describes interfaces (ABIs) that standardize communication
between the Secure World and Normal World leveraging TrustZone
technology.
This driver uses 64-bit registers as per SMCCCv1.2 spec and comes
on top of the SMCCC layer. The driver provides the FF-A ABIs needed for
querying the FF-A framework from the secure world.
The driver uses SMC32 calling convention which means using the first
32-bit data of the Xn registers.
All supported ABIs come with their 32-bit version except FFA_RXTX_MAP
which has 64-bit version supported.
Both 32-bit and 64-bit direct messaging are supported which allows both
32-bit and 64-bit clients to use the FF-A bus.
FF-A is a discoverable bus and similar to architecture features.
FF-A bus is discovered using ARM_SMCCC_FEATURES mechanism performed
by the PSCI driver.
Clients are able to probe then use the FF-A bus by calling the DM class
searching APIs (e.g: uclass_first_device).
The Secure World is considered as one entity to communicate with
using the FF-A bus. FF-A communication is handled by one device and
one instance (the bus). This FF-A driver takes care of all the
interactions between Normal world and Secure World.
The driver exports its operations to be used by upper layers.
Exported operations:
- ffa_partition_info_get
- ffa_sync_send_receive
- ffa_rxtx_unmap
Generic FF-A methods are implemented in the Uclass (arm-ffa-uclass.c).
Arm specific methods are implemented in the Arm driver (arm-ffa.c).
For more details please refer to the driver documentation [2].
[1]: https://developer.arm.com/documentation/den0077/latest/
[2]: doc/arch/arm64.ffa.rst
Signed-off-by: Abdellatif El Khlifi <abdellatif.elkhlifi@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Cc: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Cc: Jens Wiklander <jens.wiklander@linaro.org>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmS+Xv0cHGV1Z2VuLmhy
aXN0ZXZAY29sbGFib3JhLmNvbQAKCRAesx4CDqwvyMgxB/9BTjFfVaglu5+m/kiw
XEVSJSwe1H3sc5vFlMUYTSAOSF/mzdZIZHXC6THkCU1yfzu9AZXhp4mfRUiNTwth
w8bvYXm4ZjSxcGPVxVqfThN8iT/SWLpaUC8j7TosP1VKYwzpGmqLyO+ZLu7IwdH+
/wyXFuYtVQVxmSC6SMNAD5eNtS4O6pufat5e5EkhR2atZ/rhhAYmb9zv3RFuCuSM
bxqM+4/FqpENaIdMOPk7EbB3S1C5MsJS2b+s1oIRRLfItlLjpQG4nZnuJGRlL/Bg
mcqYYgHrAnFbLXVOEe5WxMKR1E2fMbtKSlJGpoYO9rSdQRzxGuyRrDm9M77GH2pJ
0Q/F
=DT1v
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-fixes-2023.10-a' of https://source.denx.de/u-boot/custodians/u-boot-at91
First set of u-boot-atmel fixes for the 2023.07 cycle:
This small fixes set includes the LTO configs for the boards that had
the SPL size up to the limit (sama5d2-based), such that more code can be
added. It also includes a fix for mmc non-removable.
If the device attached to the MMC bus is not removable, set force card-detect
bit to bypass card detection procedure, so card detection pin can be used for
other purposes.
It's also a workaround for SAMA5D2 who doesn't drive CMD if using GPIO for card
detection.
Signed-off-by: Zixun LI <zli@ogga.fr>
Reviewed-by: Eugen Hristev <eugen.hristev@collabora.com>
Drop the PLL part in SYSCRG driver and separate to be a single
PLL driver of which the compatible is "starfive,jh7110-pll".
Signed-off-by: Xingyu Wu <xingyu.wu@starfivetech.com>
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
Reviewed-by: Torsten Duwe <duwe@suse.de>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
This is required since user may want to either call the remove method
of video driver and reset the display or not call the remove method
to continue displaying until next stage.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
U-boot proper can use frame buffer address passed from SPL to reserve
the memory area used by framebuffer set in SPL so that splash image
set in SPL continues to get displayed while u-boot proper is running.
Put the framebuffer address and size in a bloblist to make them
available at u-boot proper, if in u-boot proper CONFIG_VIDEO is defined.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add method to reserve video framebuffer information using blob,
received from previous stage.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
During LPDDR initialization we will loop through a series of frequency
changes in order to train at the various operating frequencies. During
this training, accessing the DRAM_CLASS bitfield could happen during a
frequency change and cause the read to hang.
Store the DRAM type into the main structure to avoid multiple readings
while the independent phy is training.
Signed-off-by: Bryan Brattlof <bb@ti.com>
For once this adds USB support for two SoCs: the H616 and the F1C100s
series. The rest is support for LPDDR3 DRAM chips on H616 boards.
Gitlab CI passed, and I booted that briefly on an H616 and an F1C200s
board. I don't have an H616 board with LPDDR3 DRAM, but reportedly that
works for Mikhail, and doesn't regress on my DDR3 boards.
axi_emac:
- Change return value if RX packet is not ready
cadence_qspi:
- Enable flash reset for Versal NET
dt:
- Various DT syncups with Linux kernel
- SOM - reserved pmufw memory location
fpga:
- Add load event
mtd:
- Add missing dependency for FLASH_CFI_MTD
spi/nand:
- Minor cleanup in Xilinx drivers
versal-net:
- Prioritize boot device in boot_targets
- Wire mini ospi/qspi/emmc configurations
watchdog:
- Use new versal-wwdt property
xilinx:
- fix sparse warnings in various places ps7_init*
- add missing headers
- consolidate code around zynqmp_mmio_read/write
- switch to amd.com email
zynqmp_clk:
- Add handling for gem rx/tsu clocks
zynq_gem:
- Configure mdio clock at run time
zynq:
- Enable fdt overlay support
zynq_sdhci:
- Call dll reset only for ZynqMP SOCs
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCZLqHzgAKCRDKSWXLKUoM
IcdEAKCSgy0lMxb1c0adCjpkQR9x63oKbQCdGiioU+W+0moznHdI7+W2UptNt3w=
=Uzn8
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2023.10-rc1-v2' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2023.10-rc1 v2
axi_emac:
- Change return value if RX packet is not ready
cadence_qspi:
- Enable flash reset for Versal NET
dt:
- Various DT syncups with Linux kernel
- SOM - reserved pmufw memory location
fpga:
- Add load event
mtd:
- Add missing dependency for FLASH_CFI_MTD
spi/nand:
- Minor cleanup in Xilinx drivers
versal-net:
- Prioritize boot device in boot_targets
- Wire mini ospi/qspi/emmc configurations
watchdog:
- Use new versal-wwdt property
xilinx:
- fix sparse warnings in various places ps7_init*
- add missing headers
- consolidate code around zynqmp_mmio_read/write
- switch to amd.com email
zynqmp_clk:
- Add handling for gem rx/tsu clocks
zynq_gem:
- Configure mdio clock at run time
zynq:
- Enable fdt overlay support
zynq_sdhci:
- Call dll reset only for ZynqMP SOCs
This enables implementing custom logic after a bitstream was loaded
into the fpga.
Signed-off-by: Christian Taedcke <christian.taedcke@weidmueller.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Link: https://lore.kernel.org/r/20230720072724.11516-1-christian.taedcke-oss@weidmueller.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add gem_tsu and gem0_rx till gem3_rx to return proper register from
zynqmp_clk_get_register. Otherwise firmware won't be able to set clock
for these due to incorrect register address.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230720072859.3724-1-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
gem0_rx till gem3_rx and gem_tsu are missing from set rate function.
Add them, so that they can be set from pmu firmware via clock framework.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230719084912.30209-1-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
If there is no incoming package than axiemac_recv will return -1 which
in turn leads to printing `eth_rx: recv() returned error -1` error
message in eth_rx function. But missing a package is not an fatal error,
so return -EAGAIN in that case would be more suitable.
Signed-off-by: Maksim Kiselev <bigunclemax@gmail.com>
Link: https://lore.kernel.org/r/20230719065337.69280-1-bigunclemax@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Dll reset is needed only for ZynqMP platforms, add condition in tuning
to call arasan_zynqmp_dll_reset() just for ZynqMP platforms.
On other platforms like Versal NET, If this condition is not added, we
see PLM error messages when dll reset smc is called.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/d673ff3bdc5c236a7f0403c920e719684abd6059.1688991117.git.michal.simek@amd.com
Enable flash reset functionality for Versal NET platform.
In cadence_qspi.c there is weak function defined for reset, hence remove
the check for config, so that it will work for Versal and Versal NET
platforms.
Add register defines in Versal NET hardware.h for mini U-Boot flash
reset.
Add read_delay initialization for Versal NET also.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230614120452.21019-1-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
As per spec MDC must not exceed 2.5MHz, read the pclk clock
from the device tree and update the MDC clock divisor.
GEM devices support larger clock divisors and have a different
range of divisors. Program the MDIO clock divisors based on
the clock rate of the pclk clock.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20230619034922.24019-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
status and ecc_status are of unsigned type where they are compared for
negative value. This is pointed by below sparse warning. Change datatype
to int to fix this.
warning: comparison of unsigned expression in '< 0' is always false
[-Wtype-limits]
Signed-off-by: Algapally Santosh Sagar <santoshsagar.algapally@amd.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230614090359.10809-5-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
When one of the functions does not support super speed, the composite
driver forces the gadget to high speed. But the speed is never
configured in the cdns3 gadget driver. So configure the speed
in cdns3_gadget_udc_start just like in the kernel.
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Remove the regulator_set_enable() call from device probe which
resolves a regulator imbalance. This is unnecessary as
regulator_set_enable() will be called when ehci_register calls the
init_after_reset hook.
Suggested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Now that the Allwinner USB PHY driver supports the H616 quirk, let's
enable support for USB ports on that SoC.
We connect the compatible string to a new struct describing the SoCs USB
PHY properties, and unblock the PHY driver selection in Kconfig.
A later patch will enable USB support in the H616 boards' defconfigs.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
The H616 USB PHY is some kind of special snowflake: Only port2 works out
of the box, but all other ports need some help from this port2 to work
correctly: The CLK_BUS_PHY2 and RST_USB_PHY2 clock and reset need to be
enabled, and the SIDDQ bit in the PMU PHY control register needs to be
cleared. For this register to be accessible, CLK_BUS_ECHI2 needs to be
ungated. Don't ask ....
Follow the respective Linux patch (b45c6d80325b) and add a quirk bit,
triggering the special sequence as outlined above, for PHYs other than
PHY2: ungate this one special clock, and clear the SIDDQ bit. We also
pick the clock and reset from PHY2 and enable them as well.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
So far we were assigning some crude "type" (SoC name, really) to each
Allwinner USB PHY model, then guarding certain quirks based on this.
This does not only look weird, but gets more or more cumbersome to
maintain.
Remove the bogus type names altogether, instead introduce flags for each
quirk, and explicitly check for them.
This improves readability, and simplifies future extensions.
Port of Linux patch 8dd256bae653.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
At the moment we use "select" in each Allwinner SoC's Kconfig section to
include the USB PHY driver in the build. This means it cannot be disabled
via Kconfig, although USB is not really a strictly required core
functionality, and a particular board might not even include USB ports.
Rework the Kconfig part by removing the "select" lines for each SoC's
section, and instead letting it default to "y" in the PHY driver section
itself. We use "depends on !" to exclude the few SoCs we don't support
(yet). The Allwinner V3s does not enable USB (PHY) support at the moment,
even though it should work: let the PHY default to "n" to keep the
current behaviour.
Also the MUSB USB driver directly calls some functions from the PHY
driver, so let the former depend on the PHY driver.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Tested-by: Sam Edwards <CFSworks@gmail.com>
The Allwinner F1C100s implements a single USB PHY, connected to its MUSB
OTG controller. The USB PHY is of the simpler, older type (like the A10),
the only real difference is that it's indeed only one PHY.
Add a struct describing those F1C100s USB PHY properties, and connect it
to the new compatible string.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
In its of_xlate() function, the Allwinner USB PHY driver compares the
args_count variable against the number of implemented USB PHYs, although
this is the *number of arguments* to the DT phandle property. Per the DT
binding for this PHY device, this number is always one, so this check
will always fail if the particular SoC implements exactly one USB PHY.
So far this affected only the V3s (which has USB support disabled), but
the F1C100s also sports one PHY only.
Fix that check to compare args_count against exactly 1, and the args[0]
content (requested PHY number) against the number of implemented PHYs.
This fixes USB operation on the Allwinner V3s and allows to enable USB
on the Allwinner F1C100s SoC.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
The behaviour of dev_read_addr_size() is surprising as it does not
handle #address-cells and #size-cells but instead hardcodes the values
based on sizeof(fdt_addr_t).
This is different from dev_read_addr_size_index() and
dev_read_addr_size_name() both of which do read the cell sizes from the
device tree.
Since dev_read_addr_size() is only used by a single driver and this
driver is broken when CONFIG_FDT_64BIT does not match the address size
in the device tree, fix the function to behave like all of the other
similarly named functions. Drop the property name argument as the only
caller passes "reg" and this is the expected property name matching the
other similarly named functions.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> # chromebook_jerry
Tested-by: Simon Glass <sjg@chromium.org> # chromebook_bob
