To support Non-ASCII keys (ex, Fn, PgUp/Dn, arrow keys, ...), we need to
translate key code into escape sequence.
(Updated by sjg@chromium.org to move away from a function to store
keycodes, so we can easily record how many were sent. We now need to
return this from input_send_keycodes() so we know whether keys were
generated.)
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@ti.com>
The i8042 keyboard reset was not checking the results of the output
buffer after the reset command. This can jam up some KBC/keyboards.
Also, remove a write to the wrong register and the CONFIG setting
around the incorrect write.
Signed-off-by: Marc Jones <marc.jones@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@ti.com>
The BIOS leaves the keyboard enabled during boot time so that any
keystroke would interfere kernel driver initialization.
Add a way to disable the keyboard to make sure no scancode will be
generated during the boot time. Note that the keyboard will be
re-enabled again after the kernel driver is up.
This code can be called from the board functions.
Signed-off-by: Louis Yung-Chieh Lo <yjlou@chromium.org>
Signed-off-by: Louis Yung-Chieh Lo <yjlou@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@ti.com>
This change adds a board overridable function which can be used to decide
whether or not to initialize the i8042 keyboard controller. On systems where
it isn't actually connected to anything, this can save a significant amount of
boot time.
On Stumpy, this saves about 200ms on boot.
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@ti.com>
On x86, the i8042 keyboard controller driver frequently waits for the keyboard
input buffer to be empty to make sure the controller has had a chance to
process the data it was given. The way the delay loop was structured, if the
controller hadn't cleared the corresponding status bit immediately, it would
wait 1ms before checking again. If the keyboard responded quickly but not
instantly, the driver would still wait a full 1ms when perhaps 1us would have
been sufficient. Because udelay is a busy wait anyway, this change decreases
the delay between checks to 1us.
Also, this change gets rid of a hardcoded 250ms delay.
On Stumpy, this saves 100-150ms during boot.
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@ti.com>
The following commit introduces some build failures for ColdFire
platform.
commit abaef69fbe
Author: Marek Vasut <marex@denx.de>
Date: Thu Sep 13 16:51:38 2012 +0200
Add the missed header files.
Sign-off-by: Alison Wang <b18965@freescale.com>
The following warning was produced, fix it:
mcfmii.c: In function 'mcffec_miiphy_write':
mcfmii.c:318:8: warning: variable 'rdreg' set but not used [-Wunused-but-set-variable]
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: "Jin Zhengxiong-R64188" <R64188@freescale.com>
Cc: Jason Jin <jason.jin@freescale.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David Müller <d.mueller@elsoft.ch>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: U-Boot DM <u-boot-dm@lists.denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Oliver Brown <obrown@adventnetworks.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: U-Boot DM <u-boot-dm@lists.denx.de>
Add kerneldoc annotations into serial core.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Reorder the get_current() function to make it a bit more readable.
The code does not grow and there is minor change in the code logic,
where dev != NULL is now checked in any case.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Reorder serial_assign() function to get rid of the extra level of
indentation. Also, adjust the return value to be -EINVAL instead of
positive one to be more consistent.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Replace the in-place ad-hoc implementation of serial_puts() within
the drivers with default_serial_puts() call. This cuts down on the
code duplication quite a bit.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
U-Boot contains a lot of duplicit implementations of serial_puts()
call which just pipes single characters into the port in loop. Implement
function that does this behavior into common code, so others can make
easy use of it.
This function is called default_serial_puts() and it's sole purpose
is to call putc() in loop on the whole string passed to it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Since the at91sam9263, the mmc hardware support multi blocks read/write. So this driver enable it.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Since commit 957731ed (ARM: remove broken "lpd7a40x" boards),
lh7a40x cpu and serial driver have become unused. Remove them.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
On mxc, each SDHC instance has a dedicated clock, so gd->sdhc_clk is not
suitable for the multi-instance use case (initialization made directly with
fsl_esdhc_initialize()).
This patch fixes this issue by adding a configuration field for the SDHC input
clock frequency.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Eric Bénard <eric@eukrea.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Jason Liu <r64343@freescale.com>
Cc: Matt Sealey <matt@genesi-usa.com>
Cc: Andy Fleming <afleming@gmail.com>
Before this patch, i2c_{read,write} always returned 0.
Check TACK in i2c_raw_{read,write} so that i2c_{read,write} return non-zero when error.
Acked-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
Before this patch i2c_probe() always returned 0 and "i2c probe" command did not work properly.
Modify i2c_set_addr() to check TACK when waiting DTE and make i2c_probe() call this function.
Acked-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
sh_i2c.c support I2C0 and I2C1. This patch extends it to I2C4.
Acked-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
Adjust i2c_raw_read() in sh_i2c.c to work for SH73A0.
After this patch, "i2c md" and "i2c mw" command on U-Boot work properly on KZM-A9-GT board.
Acked-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
Correct BUSY bit define in ICSR from (1<<3) to (1<<4).
Acked-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
R-mobile SoC (at least SH73A0) has extension bits to store 8th bit of iccl and icch.
This patch add support for the extentin bits.
Acked-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
The i.MX51 has a single USB PHY clock, while the i.MX53 has two. These 3 clocks
have different clock gate control bit-fields.
The existing code was correct only for i.MX53, so this patch fixes the i.MX51
use case.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Jana Rapava <fermata7@gmail.com>
Cc: Wolfgang Grandegger <wg@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Use clock gate definitions having names showing clearly the gated clock instead
of names giving only a register field index.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
i2c didn't work on imx25 due to missing MXC_IPG_PERCLK. Now using
MXC_I2C_CLK on all imx systems using i2c.
Signed-off-by: Matthias Weisser <weisserm@arcor.de>
Acked-by: Stefano Babic <sbabic@denx.de>
Add meaningful constants for each clock channels and use them for
enabling and disabling i.MX6 clocks.
Includes an update to enable/disable the IPU1 clock in
drivers/video/ipu_common to remove IMX5x register access
when used on i.MX6 as discussed in V1:
http://patchwork.ozlabs.org/patch/185129/
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Boards may require a different pinmux setup for NAND than the default one.
Add a way to call into board specific code to set this up.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The move is pretty straight-forward. ap20.h and tegra20.h were renamed to ap.h and tegra.h.
Some files remain in arch-tegra20 but 'include' a file in 'arch-tegra' with #defines & structs
that will be common between T20 and T30 HW. HW-specific #defines, etc. stay in the 'arch-tegra20'
'root' file.
All boards build OK w/MAKEALL -s tegra20. Checkpatch.pl runs clean. Seaboard works OK.
Signed-off-by: Tom Warren <twarren@nvidia.com>
These are read from the fdt - add a debug feature to display the mapping
on start-up.
See that we get debug output listing the keycodes
Signed-off-by: Simon Glass <sjg@chromium.org>
It is inconvenient to have to specify the keyboard repeat and delay at
init time if it is not yet available, so move this into a separate
function.
Some drivers will want to do this when their keyboard init routine
is actually called.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some issues with this were not addressed in the previous series. Fix up
the binding decoding to deal with what is actually expected in the fdt.
This corrects the broken keyboard on seaboard.
Signed-off-by: Simon Glass <sjg@chromium.org>
- block_dev_desc_t says that block_(read|write) take lbaint_t for blkcnt
not ulong.
- We also move the extern of sata_dev_desc into <sata.h>
- Remove now duplicate declarations from driver-specific headers.
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Pavel Herrmann <morpheus.ibis@gmail.com>
sata_write() takes a const void as the last argument. Fixing this means
we also need to make ata_low_level_rw_lba{28,48} also take a const void.
Signed-off-by: Tom Rini <trini@ti.com>
- sata_write() takes a const void as the last argument. Fixing this
means we also need to make ata_low_level_rw_lba{28,48} also take a
const void.
- Both sata_{read,write} take lbaint_t for blkcnt and ulong for blknr
Signed-off-by: Tom Rini <trini@ti.com>
sata_write() takes a const void as the last argument. Fixing this means
we also need to make ata_low_level_rw_lba{28,48} also take a const void.
Acked-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Add to pxa25x based devices support for USB ethernet gadget. This is a
port of pxa25x UDC driver from Linux kernel.
Signed-off-by: Lukasz Dalek <luk0104@gmail.com>
Removed DEV_CONFIG_CDC and DEV_CONFIG_SUBSET and replaced it with
CONFIG_USB_ETH_CDC and CONFIG_USB_ETH_SUBSET.
Signed-off-by: Lukasz Dalek <luk0104@gmail.com>
Introduced CONFIG_USB_ETH_CDC and CONFIG_USB_ETH_SUBSET as preparation
for removal DEV_CONFIG_CDC and DEV_CONFIG_SUBSET
Signed-off-by: Lukasz Dalek <luk0104@gmail.com>
PXA25X chips don't support alternate settings so driver uses non-CDC
driver.
But only code defined between DEV_CONFIG_CDC signals that network is up.
This patch is fixing this bug by signaling that network is up after USB
SET_INTERFACE request.
Signed-off-by: Lukasz Dalek <luk0104@gmail.com>
Allows for easy configuration of the VBUS indicator related ULPI
config bits.
Also move the external indicator setup from ulpi_set_vbus() to
the new function.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Allows to initialize more than one USB controller at once.
v2: print message when controller stop fails
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Kill off ehci-core.h
It was used to specify some static controller data. To support more than
one controller being active at any time we have to carry the controller
data ourselfes. Change the ehci interface accordingly.
NOTE: OMAP implemented the ehci stuff a bit backwards and should be fixed
to do the same thing as other platforms. But the change for now is at least
compile clean.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Carry an index in the lowlevel usb functions to make specify the
respective usb controller.
Also pass through an controller struct from lowlevel_init to the
creation of the root usb device of this controller.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Reviewed-by: Marek Vasut <marex@denx.de>
As the board seems to be unmaintained for some time, lets remove
the support in mainline completely.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: James MacAulay <james.macaulay@amirix.com>
Acked-by: Marek Vasut <marex@denx.de>
Enhance the manual relocation of drivers operations structure by
checking if the entries are NULL and increment them only if they
are not. This allows for setting any entry to NULL and it will
survive the manual relocation.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Compile drivers/serial/serial.c by default both into SPL and into
non-SPL builds, since CONFIG_SERIAL_MULTI is now the default state.
Also having common/serial.c in by default now, it's pointless to keep
-DCONFIG_SERIAL_MULTI in CPPFLAGS any longer, so remove it as well.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Remove the support for not-CONFIG_SERIAL_MULTI part from serial
port drivers and some board files. Since CONFIG_SERIAL_MULTI is
now enabled by default, that part is a dead code. Remove it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Enable CONFIG_SERIAL_MULTI for all builds of U-Boot. That includes
both SPL builds and non-SPL builds, everything. To avoid poluting
this patch with removal of ifdef-endif constructions containing
CONFIG_SERIAL_MULTI, the CONFIG_SERIAL_MULTI is temporarily added
into CPPFLAGS in config.mk . This will be again removed in following
patch.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Move the common/serial.c into driver/serial/, since this file
provides serial multiplexing functions and it is imperative to
be linked with libserial.o instead of libcommon.o.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
This serial driver had wrong name of the source file for some time
now. The name of the driver was serial.c instead of any more logical
and fitting name. Thus, rename the driver source file to serial_ns16550.c
and be done with it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Michal Simek <monstr@monstr.eu>
Having both USBTTY and CONFIG_SERIAL_MULTI enabled in SPL, the
usbtty.c file is protected in Makefile to not be compiled into
the SPL. Yet, the ns16550 serial driver does not contain such
protection. Add it to avoid missing symbol error.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Implement support for CONFIG_SERIAL_MULTI into sh serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the sh driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Phil Edworthy <PHIL.EDWORTHY@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Tom Rini <trini@ti.com>
Implement support for CONFIG_SERIAL_MULTI into sa1100 serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the sa1100 driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Implement support for CONFIG_SERIAL_MULTI into s3c44b0 serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the s3c44b0 driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Implement support for CONFIG_SERIAL_MULTI into pl01x serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the pl01x driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Mathieu J. Poirier <mathieu.poirier@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: John Rigby <john.rigby@linaro.org>
Cc: Rabin Vincent <rabin.vincent@stericsson.com>
Implement support for CONFIG_SERIAL_MULTI into netarm serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the netarm driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Stefano Babic <sbabic@denx.de>
Implement support for CONFIG_SERIAL_MULTI into mxc serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the mxc driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Stefano Babic <sbabic@denx.de>
Implement support for CONFIG_SERIAL_MULTI into max3100 serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the max3100 driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Implement support for CONFIG_SERIAL_MULTI into lpc2292 serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the lpc2292 driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Implement support for CONFIG_SERIAL_MULTI into lh7a40x serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the lh7a40x driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Implement support for CONFIG_SERIAL_MULTI into ks8695 serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the ks8695 driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Implement support for CONFIG_SERIAL_MULTI into ixp serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the ixp driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Michael Schwingen <michael@schwingen.org>
Implement support for CONFIG_SERIAL_MULTI into imx serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the imx driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Stefano Babic <sbabic@denx.de>
Implement support for CONFIG_SERIAL_MULTI into clps7111 serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the clps7111 driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Implement support for CONFIG_SERIAL_MULTI into sandbox serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the sandbox driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Implement support for CONFIG_SERIAL_MULTI into s3c64xx serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the s3c64xx driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: John Rigby <john.rigby@linaro.org>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Implement support for CONFIG_SERIAL_MULTI into s3c4510b serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the s3c4510b driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Implement support for CONFIG_SERIAL_MULTI into OpenCores serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the OpenCores driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Scott McNutt <smcnutt@psyent.com>
Implement support for CONFIG_SERIAL_MULTI into ns9750 serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the ns9750 driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Implement support for CONFIG_SERIAL_MULTI into MCF serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the MCF driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: TsiChung Liew <tsicliew@gmail.com>
Implement support for CONFIG_SERIAL_MULTI into lpc32xx serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the lpc32xx driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Implement support for CONFIG_SERIAL_MULTI into atmel serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the atmel driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Xu, Hong <Hong.Xu@atmel.com>
Implement support for CONFIG_SERIAL_MULTI into altera serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the altera driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Scott McNutt <smcnutt@psyent.com>
Implement support for CONFIG_SERIAL_MULTI into altera_jtag serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the altera_jtag driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Thomas Chou <thomas@wytron.com.tw>
Move the registration of eserialN_device ports from default
serial_initialize() into driver specific function called from
serial_initialize(). This slims down the serial_initialize() call
to a bare tracker of all possible serial port registration routines
in U-Boot.
The newly implemented ns16550_serial_initialize() function, which is
implemented inside of the ns16550 serial driver allows encapsulation
of eserialN_device within the ns16550 serial driver itself.
Also, remove the exports of eserialN_device from include/serial.h
as they are no longer needed. This is simply because the implementation of
default_serial_console() is wrapped into the ns16550 serial driver and
the default console is picked by CONFIG_SERIAL<N> macro in config file.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Michal Simek <monstr@monstr.eu>
Move the registration of xuartlite_serialN_device ports from
default serial_initialize() into driver specific function called from
serial_initialize(). This slims down the serial_initialize() call
to a bare tracker of all possible serial port registration routines
in U-Boot.
The newly implemented xuartlite_serial_initialize() function, which is
implemented inside of the serial_xuartlite driver allows encapsulation
of xuartlite_serialN_device within the serial_xuartlite driver itself.
Also, remove the exports of xuartlite_serialN_device from include/serial.h
as they are no longer needed. This is simply because the implementation of
default_serial_console() is wrapped into the serial_xuartlite driver and
the default console is picked by CONFIG_SERIAL<N> macro in config file.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Michal Simek <monstr@monstr.eu>
Move the registration of zynq_serialN_device ports from default
serial_initialize() into driver specific function called from
serial_initialize(). This slims down the serial_initialize() call
to a bare tracker of all possible serial port registration routines
in U-Boot.
The newly implemented zynq_serial_initialize() function, which is
implemented inside of the serial_zynq driver allows encapsulation
of zynq_serialN_device within the serial_zynq driver itself.
Also, remove the exports of zynq_serialN_device from include/serial.h
as they are no longer needed. This is simply because the implementation of
default_serial_console() is wrapped into the serial_zynq driver and
the default console is picked by CONFIG_SERIAL<N> macro in config file.
Signed-off-by: Tom Rini <trini@ti.com>
Move the registration of s5p_serialN_device ports from default
serial_initialize() into driver specific function called from
serial_initialize(). This slims down the serial_initialize() call
to a bare tracker of all possible serial port registration routines
in U-Boot.
The newly implemented s5p_serial_initialize() function, which is
implemented inside of the serial_s5p driver allows encapsulation
of s5p_serialN_device within the serial_s5p driver itself.
Also, remove the exports of s5p_serialN_device from include/serial.h
as they are no longer needed. This is simply because the implementation of
default_serial_console() is wrapped into the serial_s5p driver and
the default console is picked by CONFIG_SERIAL<N> macro in config file.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Move the registration of serial_XXuart ports from default
serial_initialize() into driver specific function called from
serial_initialize(). This slims down the serial_initialize() call
to a bare tracker of all possible serial port registration routines
in U-Boot.
The newly implemented pxa_serial_initialize() function, which is
implemented inside of the serial_pxa driver allows encapsulation
of serial_XXuart within the serial_pxa driver itself.
Also, remove the exports of serial_XXuart from include/serial.h
as they are no longer needed. This is simply because the implementation of
default_serial_console() is wrapped into the serial_pxa driver and
the default console is picked by CONFIG_CONS_IDX macro in config file.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Move the registration of s3c24xx_serialN_device ports from
default serial_initialize() into driver specific function called from
serial_initialize(). This slims down the serial_initialize() call
to a bare tracker of all possible serial port registration routines
in U-Boot.
The newly implemented s3c24xx_serial_initialize() function, which is
implemented inside of the serial_s3c24xx driver allows encapsulation
of s3c24xx_serialN_device within the serial_s3c24xx driver itself.
Also, remove the exports of s3c24xx_serialN_device from include/serial.h
as they are no longer needed. This is simply because the implementation of
default_serial_console() is wrapped into the serial_s3c24xx driver and
the default console is picked by CONFIG_SERIAL<N> macro in config file.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: C Nauman <cnauman@diagraph.com>
Make functions that are local-only static, so no hairy symbols
stick out of the serial_pxa driver file.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Implement weak default_serial_console() function in serial_pxa
driver, which gets available in case CONFIG_SERIAL_MULTI is
enabled. This will get helpful in subsequent patches, which will
encapsulate PXA's struct serial_device instances in serial_pxa
driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Properly spell out the whole structure member names when an initialized
varible is instantiated from the struct serial_driver. In case the
structure definition for struct serial_driver undergoes reordering,
there will be no impact on variables defined based on this structure.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: C Nauman <cnauman@diagraph.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Michal Simek <monstr@monstr.eu>
Rename .init() to .start() and .uninit() to .stop() in struct
serial_device. This allows aligning struct serial_device with
closer to struct stdio_dev. The real goal here is to allow
these two structures to converge together and eventually make
one to be a superset of the other.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Tom Rini <trini@ti.com>
Use the standard CMD_RET_* constants to clearly report errors from the
pca953x command. In addition, print error messages when I2C communication
fails.
Signed-off-by: Laurence Withers <lwithers@guralp.com>
Due to grown code sizes the TQM85xx boards don't build any more with
some older tool chains (like ELDK 4.2). As these boards have long
reached EOL it seems a waste of effort trying to fix them. The vendor
has agreed to drop support for them, too. So let's get rid of them.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
cc: Kim Phillips <kim.phillips@freescale.com>
Acked-by: Stefan Roese <sr@denx.de>
The driver is used on Xilinx Zynq platform.
Signed-off-by: Michal Simek <monstr@monstr.eu>
CC: Joe Hershberger <joe.hershberger@gmail.com>
CC: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
It's now possible to use the gpio driver interface
for s3c2440. This patch add iomux definitions too.
Signed-off-by: Gabriel Huau <contact@huau-gabriel.fr>
irq_wait function is not referred to from anywhere.
Reported-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Extend the driver for placing the video/bmp logo as specified
by "splashpos" environment variable.
Signed-off-by: Bastian Ruppert <Bastian.Ruppert@Sewerin.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
CC: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
We set sata_curr_device to 0 right after returning from init_sata(), so there's
no point in setting it to the last scanned driver at this point.
Note: there are more duplicities with cmd_sata, but those might be required,
as the code seems to reset the entire controller on every scan, ignoring the
requested port number.
Signed-off-by: Pavel Herrmann <morpheus.ibis@gmail.com>
- Convert the non-relocation part of board_init_f to spl_board_init, turn on CONFIG_SPL_BOARD_INIT in the configs.
- Remove duplicated code.
- Add spl_boot_device() that returns the statically chosen boot device.
Signed-off-by: Tom Rini <trini@ti.com>
The mechanism waiting for transmission to finish in fec_send() now
relies on the E-bit being cleared in the TX buffer descriptor. In
case of data cache being on, this means invalidation of data cache
above this TX buffer descriptor on each test for the E-bit being
cleared.
Apparently, there is another way to check if the transmission did
complete. This is by checking the TDAR bit in the X_DES_ACTIVE
register. Reading a register does not need any data cache invalidation,
which is beneficial.
Rework the sequence that wait for completion of the transmission so that
the TDAR bit is tested first and afterwards check the E-bit being clear.
This cuts down the number of cache invalidation calls to one.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
The FEC hardware sometimes errors out on data transfer and hangs in
the tightloop adjusted by this patch. So add timeout into the tightloop
to make such a hang recoverable.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
Align the address that's to be invalidated/flushed properly.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Benoit Thebaudeau <benoit.thebaudeau@advans>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Do not pass unaligned RX buffer to the upper layers. The upper layer,
especially in the ARP case, recycles the buffer and passes it back into
the FEC, into it's TX path. With caches enabled, the FEC hangs on this
from time to time.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Benoit Thebaudeau <benoit.thebaudeau@advans>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
-VSC8662 is Dual Port 10/100/1000Base-T Phy,
100Base-FX/1000/Base-X Gigabit Ethernt Transceiver Phy.
-Its register set and features are similar to
other Vitesse Phys
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
This patch add support for the configuration of an external switch from
the 88E6xxx series from Marvell trough an MDIO link using indirect
adressing. This can be used if we do not want to use an EEPROM for the
configuration.
This driver is not generic and was not tested on other switches than the
88e6352. This is proposed as a first implementation that is somewhat
limited but works and that can be used as a basis for further
developments for this switch family.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
cc: Joe Hershberger <joe.hershberger@gmail.com>
Add a new flag, CONFIG_SPL_FRAMEWORK to opt into the common/spl SPL
framework, enable on all of the previously using boards. We move the
spl_ymodem.c portion to common/ and spl_mmc.c to drivers/mmc/. We leave
the NAND one in-place as we plan to replace it later in this series.
We use common/spl to avoid linker problems with respect to merging
constant strings in objects. Otherwise all strings in common/ will be
linked in and kept which grows SPL in size too much.
Signed-off-by: Tom Rini <trini@ti.com>
Device driver for Zynq Gem IP.
Signed-off-by: Michal Simek <monstr@monstr.eu>
CC: Joe Hershberger <joe.hershberger@gmail.com>
CC: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Add AX88772B ID together with two fixes needed to make this work.
1. The packet length check has to be adjusted, as all ASIX chips
only use 11 bits to indicate the length. AX88772B uses the other
bits to indicate unrelated things, which cause the check to fail.
This fix is based on a fix for the Linux kernel by Marek Vasut.
Linux upstream commit: bca0beb9363f8487ac902931a50eb00180a2d14a
2. AX88772B provides several bulk endpoints. Only the first
IN/OUT endpoints work in the default configuration. So stop
enumeration after we found them to avoid overwriting the
endpoint config with a non-working one.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Initial device MAC should be read while getting info about the
device, so it's wrong to only read it in asix_init().
Add a dedicated function to read the initial MAC, which is also
able to handle devices that have their initial MAC stored in
EEPROM. Call this function inasix_eth_get_info().
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
All ASIX chipsets aside from AX88172 are able to set the MAC
address on the hardware level. Add a function to expose this
ability.
To differentiate between chip types we now carry flags as driver
private data. Also while touching the asix_dongles array
constify this.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The basic device reset ensures that the device is ready to
service commands and does not need to get redone before each
network operation.
Split out the basic reset from asix_init() and instead call it
from asix_eth_get_info(), so that it only gets called once.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Avoid clutter in ueth_data. Individual drivers should not mess
with structures belonging to the core like this.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Check the incoming packets' source IP address... if ncip isn't set to a
broadcast address, only listen to the client at ncip.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Refresh the netconsole settings from the env before each packet instead
of only on netconsole init.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Previously u-boot would initialize the network interface for every
network operation and then shut it down again. This makes sense for
most operations where the network in not known to be needed soon after
the operation is complete. In the case of netconsole, it will use the
network for every interaction with the shell or every printf. This
means that the network is being reinitialized very often. On many
devices, this intialization is very slow.
This patch checks for consecutive netconsole actions and leaves the
ethernet hardware initialized between them. It will still behave the
same old way for all other network operations and any time another
network operation happens between netconsole operations.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
Allow a board to configure a larger buffer for netconsole, but leave
the default.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
R8A7740 of rmobile has ethernet device, and this is same IP of
sh-ether. This support R8A7740 of rmobile.
Signed-off-by: Hideyuki Sano <hideyuki.sano.dn@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Apply the following questionable adjustment to silence GCC.
armada100_fec.c: In function ‘armdfec_send’:
armada100_fec.c:589:2: warning: dereferencing type-punned pointer will break strict-aliasing rules [-Wstrict-aliasing]
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
Support new CONFIG_OF_CONTROL option where device
probing is done based on device tree description.
Signed-off-by: Michal Simek <monstr@monstr.eu>
CC: Joe Hershberger <joe.hershberger@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Bryan Hundven <bryanhundven@gmail.com>
Cc: Michael Schwingen <rincewind@discworld.dascon.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: U-Boot DM <u-boot-dm@lists.denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
It is desirable to use different port numbers for sending and receiving
packets with netconsole in the case where you have more than one device
on the local subnet with netconsole enabled for broadcast. When they
use the same port for both, any output from one will look like input to
the other. This is typlically not desirable.
This patch allows the input and output ports to be specified separately
in the environment.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
The following commit introduced some warnings associated with using
pci_addr_t instead of a proper 32-bit data type.
commit af778c6d9e
Author: Andrew Sharp <andywyse6@gmail.com>
Date: Wed Aug 1 12:27:16 2012 +0000
pci: fix errant data types and corresponding access functions
On some platforms pci_addr_t is defined as a 64-bit data type so its not
proper to use with pci_{read,write}_config_dword.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Several DIU registers were being initialized either unnecessarily or to
wrong values.
1) All interrupts were enabled even though there's no interrupt handler.
Interrupts were left enabled when booting Linux.
2) Don't configure a dummy area descriptor, since we don't support ADs
in U-Boot.
3) Don't configure any write-back buffer registers, since we don't use
that mode.
4) The default values for the THRESHOLDS, SYN_POL, and PLUT registers
should be used, so don't touch those registers either.
Signed-off-by: Timur Tabi <timur@freescale.com>
usb_hub_descriptor has to be packed as it's used for
communication with the device. Member wHubCharacteristics
violates the natural alignment rules.
Use explicit unaligned access functions for this member.
Fixes ARMv7 traping while using USB.
v2: fix typo found by Thomas Langer
v3: rebased on top of u-boot-usb/master
Signed-off-by: Lucas Stach <dev@lynxeye.de>
The "filesize" environment variable shall be read only when relevant
file is read.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Support for ext4 file system handling at DFU.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Marek Vasut <marex@denx.de>
This patch adds a driver for Freescale Colfire Queued SPI bus.
Coded to work with 8 bits per transfer to use with SPI flash.
CPOL, CPHA, and CS_ACTIVE_HIGH can be configured.
Tested with MCF5270 which have 4 chip selects.
Activate by #define CONFIG_CF_QSPI in board config.
Signed-off-by: Richard Retanubun <richardretanubun@ruggedcom.com>
The MPC8308RDB Reference Manual states that no bits in the SPMODE
register are allowed to change while the enable (EN) bit is set.
This driver changes the character length bits (LEN) while the enable
(EN) bit is set. Clearing the EN bit while changing the LEN bits makes
the driver work correctly on MPC8308RDB.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
