distro_bootcmd uses this construct a few times to test $fdt_addr_r,
and fall back on $fdtcontroladdr if not set/invalid:
if fdt addr ${fdt_addr_r}; then
...
else
...
fi
If the `fdt addr` test fails, it prints the following message on the
console, suggesting there is an error when there is not:
libfdt fdt_check_header(): FDT_ERR_BADMAGIC
To remove this potentially confusing error message, this patch adds -q
as a 'quiet' option for fdt addr, and uses this flag in
config_distro_bootcmd.h
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
Add the ability to save ADC conversion result in an environment
variable. This is useful for further arbitrary processing by the
U-Boot scripts.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
As explained in commit 4af2a33ee5 ("cmd: gpio: Make `gpio input`
return pin value again") the `gpio input` is used in scripts to obtain
the value of a pin, despite the fact that CMD_RET_FAILURE is
indistinguishable from a valid pin value.
To be able to detect failures and properly use the value of a GPIO in
scripts we introduce the `gpio read` command that sets the variable
`name` to the value of the pin. Return code of the `gpio read` command
can be used to check for CMD_RET_SUCCESS or CMD_RET_FAILURE.
CONFIG_CMD_GPIO_READ is used to enable the `gpio read` command.
Signed-off-by: Diego Rondini <diego.rondini@kynetics.com>
Attaching a UBI partition may take a while, since scanning the memory is
required.
It thus makes sense to avoid a detach/scan/attach cycle when the right
partition is already attached, and let the calling process call 'detach'
beforehand if it needs it.
This commit checks for the currently attached UBI partition, and skips
reattaching if not needed, showing an information.
Signed-off-by: Alexandre Besnard <alexandre.besnard@softathome.com>
virtio_init() enumerates all the peripherals that are to be materialised
with udevices(UCLASS_VIRIO) and creates particular device instances
(UCLASS_BlK or whatever else) as children.
On the other hand, device_probe() won't be invoked against those resultant
udevices unlike other ordinary device drivers do in the driver model.
This is particularly inconvenient when we want to add "event notification"
callback so that we will be able to automatically create all efi_disk
objects in a later patch.
With this patch applied, "virtio scan" will work in a similar way
to "scsi rescan", "usb start" or others in term of 'probe' semantics.
I didn't add this change to virtio_init() itself because this function
may be called in board_init_r() (indirectly in board_late_init())
before UEFI subsustem is initialized.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Disable 'capsule disk-update' option for the efidebug command
when CONFIC_EFI_CAPSULE_ON_DISK is disabled, because this option
is available only when the EFI capsule update on disk is enabled.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Suggested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This allows an ergonomic-enough approximation of ${!variable} expansion.
This could be used the following way:
```
for target in ${boot_targets}; do
env indirect target_name target_name_${target}
# ...
done
```
Assuming `target_name_mmc0` and similar are set appropriately.
A default value can be optionally provided.
Note: this acts on environment variables, not hush variables.
Signed-off-by: Samuel Dionne-Riel <samuel@dionne-riel.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: "Marek Behún" <marek.behun@nic.cz>
[trini: Don't enable by default]
Let the sbi command display:
* machine vendor ID
* machine architecture ID
* machine implementation ID
With this patch the output for the HiFive Unmatched looks like
=> sbi
SBI 0.3
OpenSBI 0.9
Machine:
Vendor ID 489
Architecture ID 8000000000000007
Implementation ID 20181004
Extensions:
sbi_set_timer
sbi_console_putchar
sbi_console_getchar
sbi_clear_ipi
sbi_send_ipi
sbi_remote_fence_i
sbi_remote_sfence_vma
sbi_remote_sfence_vma_asid
sbi_shutdown
SBI Base Functionality
Timer Extension
IPI Extension
RFENCE Extension
Hart State Management Extension
System Reset Extension
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Version 1.0-rc3 of the RISC-V Supervisor Binary Interface Specification
has added the Performance Monitoring Unit Extension.
The sbi command should be able to detect it.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Most U-Boot command deal with start/size instead of start/end. Convert
the "fdt chosen" command to use these semantics as well. The only user
of this subcommand is vexpress, so convert the smhload command to use
this as well. We don't bother renaming the variable in vexpress64's
bootcommand, since it will be rewritten in the next commit.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Add a subcommand preload to bootm that execute the preload
stage on the image. Right now, it checks the signature
of the image with the pre-load header. If the check
succeed, the u-boot env variable 'loadaddr_verified'
is set to the address of the image (without the header).
It allows to run such commands:
tftp script.img && bootm preload $loadaddr && source $loadaddr_verified
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Add a stage pre-load to the command bootm.
Right now, this stage may be used to read a
header and check the signature of the full
image.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Drop the Kconfigs which are not used and all references to them. In
particular, this drops CONFIG_VIDEO to avoid confusion and allow us to
eventually rename CONFIG_DM_VIDEO to CONFIG_VIDEO.
Also drop the prototype for video_get_info_str() which is no-longer used.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Jason Liu <jason.hui.liu@nxp.com>
The non-driver model video support was removed two years ago. Drop this
driver, which is only used by nokia_rx51.
Signed-off-by: Simon Glass <sjg@chromium.org>
When calling efi_dp_from_name() we are not interested in the device part.
Just pass NULL as an argument.
Suggested-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
With DM I2C, the EEPROM bus has been correctly configured in
eeprom_execute_command() already. Do not reconfigure it here
with hard-coded bus number again.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
The GUID of partitions is sufficient for identification and will stay
constant in the lifetime of a boot option. The preceding path of the
device-path may change due to changes in the enumeration of devices.
Therefore it is preferable to use the short-form of device-paths in load
options. Adjust the 'efidebug boot add' command accordingly.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
For targets that enable ACPI, we should not pass Device Trees into
the payload. However, our distro boot logic always passes the builtin
DT as an argument.
To make it easy to use ACPI with distro boot, let's just ignore the DT
argument to bootefi when ACPI is enabled. That way, we can successfully
distro boot payloads on ACPI enabled targets.
Signed-off-by: Alexander Graf <agraf@csgraf.de>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
e-MMC and SD standards differ for some CID fields:
- 6 Byte Name - assigned by Manufacturer (SD 5 Byte)
- 1 Byte OEM - assigned by Jedec (SD 2 Byte)
See e-MMC standard (JEDEC Standard No. 84-B51), 7.2.3 (OID) and 7.2.4 (PNM)
Signed-off-by: Max Merchel <Max.Merchel@tq-group.com>
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Currently the cls command does not support the serial console
The screen can be cleared in the video uclass, the colored frame buffer
console, and the serial console by sending the same escape sequence.
This reduces the cls command to a single printf() statement on most
boards.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_BOOTP_MAY_FAIL
CONFIG_BOOTP_VENDOREX
CONFIG_BOOTP_BOOTFILESIZE
CONFIG_BOOTP_NISDOMAIN
CONFIG_BOOTP_TIMEOFFSET
Cc: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
The arm64 version of the exception command was just defining the
undefined exception, but actually copied the AArch32 instruction.
Replace that with an encoding that is guaranteed to be and stay
undefined. Also add instructions to trigger unaligned access faults and
a breakpoint.
This brings ARM64 on par with ARM(32) for the exception command.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
UEFI specification requires that 5 minutes watchdog timer is
armed before the firmware's boot manager invokes an EFI boot option.
This watchdog timer is updated as follows, according to the
UEFI specification.
1) The EFI Image may reset or disable the watchdog timer as needed.
2) If control is returned to the firmware's boot manager,
the watchdog timer must be disabled.
3) On successful completion of EFI_BOOT_SERVICES.ExitBootServices()
the watchdog timer is disabled.
1) is up to the EFI image, and 3) is already implemented in U-Boot.
This patch implements 2), the watchdog is disabled when control is
returned to U-Boot.
In addition, current implementation arms the EFI watchdog at only
the first "bootefi" invocation. The EFI watchdog must be armed
in every EFI boot option invocation.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Update the result of do_clk_setfreq and always returns a CMD_RET_ value
(-EINVAL was a possible result).
This patch avoid the CLI output "exit not allowed from main input shell."
Fixes: 7ab418fbe6 ("clk: add support for setting clk rate from cmdline")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Link: https://lore.kernel.org/r/20220131172131.3.Iec2029edb7fc0b29e13bcb86058ad2f614f62779@changeid
The function clk_lookup can be replaced by a direct call
to uclass_get_device_by_name for UCLASS_CLK.
This patch removes duplicated codes by the generic DM API and avoids
issue in clk_lookup because result of uclass_get_device wasn't tested;
when ret < 0, dev = NULL and dev->name is invalid, the next function
call strcmp(name, dev->name) causes a crash.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20220131172131.2.I7bc7762eff1e31ab7ff5b34c416ee03b8fe52200@changeid
Test the number of argument in setfreq command to avoid a crash when
the command setfreq is called without argument:
STM32MP> clk setfreq
data abort
pc : [<ddba3f18>] lr : [<ddba3f89>]
reloc pc : [<c018ff18>] lr : [<c018ff89>]
sp : dbaf45b8 ip : ddb1d859 fp : 00000002
r10: dbb3fd80 r9 : dbb11e90 r8 : ddbf38cc
r7 : ddb39725 r6 : 00000000 r5 : 00000000 r4 : dbb3fd84
r3 : dbb3fd84 r2 : 0000000a r1 : dbaf45bc r0 : 00000011
Flags: nzCv IRQs off FIQs off Mode SVC_32 (T)
Code: 4dd3 1062 85a3 ddbd (7803) 2b30
Resetting CPU ...
Fixes: 7ab418fbe6 ("clk: add support for setting clk rate from cmdline")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Link: https://lore.kernel.org/r/20220131172131.1.I32a8f213d330dccd922f7aafc60d3d63fcbe8615@changeid
With the fuse values in memory we can use some of the other u-boot shell
conditonal operators to do tests.
Signed-off-by: Angus Ainslie <angus@akkea.ca>
The pstore command tries to create a reserved-memory node but fails if
it is already present with:
Add 'reserved-memory' node failed: FDT_ERR_EXISTS
This patch creates the node only if it does not exist and adapts the reg
values sizes depending on already present #address-cells and #size-cells
values.
Signed-off-by: Detlev Casanova <detlev.casanova@collabora.com>
Since dfu is not only used for USB, and some platform only
supports DFU_OVER_TFTP or EFI capsule update, dfu_alt_info
is defined on such platforms too.
For such platform, 'dfu list' command is useful to check
how the current dfu_alt_info setting is parsed.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
strlen() returns size_t. So we should use %zu to print it.
This avoids incorrect output on 32bit systems.
Fixes: 2fc62f2991 ("stackprot: Make our test a bit more complex")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
In case the eMMC contains any GP partitions or user sets up new GP
partitions, the size of these GP partitions reduce the size of the
USER partition. Subtract the size of those GP partitions from the
calculated size of USER partition when using `user enh start -`.
The following test used to fail before:
```
u-boot=> mmc hwpartition gp1 524288 enh user enh 0 - wrrel on check
Partition configuration:
User Enhanced Start: 0 Bytes
User Enhanced Size: 1.8 GiB
User partition write reliability: on
GP1 Capacity: 256 MiB ENH
No GP2 partition
No GP3 partition
No GP4 partition
Total enhanced size exceeds maximum (261 > 229)
Failed!
```
The test now passes:
```
u-boot=> mmc hwpartition gp1 524288 enh user enh 0 - wrrel on check
Partition configuration:
User Enhanced Start: 0 Bytes
User Enhanced Size: 1.5 GiB
User partition write reliability: on
GP1 Capacity: 256 MiB ENH
No GP2 partition
No GP3 partition
No GP4 partition
```
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The operation of this function can be confusing. Add some debugging so
we can see what it is doing and when it is called.
Also drop the preprocessor usage.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: heinrich Schuchardt <xypron.glpk@gmx.de>
Without this patch the bcb struct could be located at an odd address
which resulted in data not being copied to the buffer.
Here was the repro steps (from Mattijs):
=> mmc dev 1
=> bcb load 1 misc
=> bcb dump command
00000000: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00000010: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
=> part start mmc 1 misc misc_start
=> mmc read ${loadaddr} ${misc_start} 4
=> bcb load 1 misc
=> bcb dump command
00000000: 62 6f 6f 74 6f 6e 63 65 2d 62 6f 6f 74 6c 6f 61
00000010: 64 65 72 00 00 00 00 00 00 00 00 00 00 00 00 00
This behavior was observed on an Amlogic A311D (ARM64) platform with a
recent GCC toolchain (11.2.0) but is most likely affecting other
platforms.
To avoid issues the structure is aligned on DMA minimum alignment value
as it is passed directly to the read function.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> # on khadas vim3
At present we use wide characters for unicode but this is not necessary.
Change the code to use the 'u' literal instead. This helps to fix build
warnings for sandbox on rpi.
Signed-off-by: Simon Glass <sjg@chromium.org>
Suggested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Allow to call 'pci' and 'pci regions' commands with bus option '*' which
cause pci to process all buses.
PCIe is point-to-point HW and so on each bus is maximally one physical
device. Therefore for PCIe it is common to have multiple buses.
This change allows to easily print all available PCIe devices in system.
Make '*' as default option when no bus argument is specified.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Currently pci command ignores invalid cmdline arguments and do something.
Add checks that all passed arguments were processed.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
'pci regions' currently prints only region information from bus 0 which
belongs to controller 0. Parser for 'pci regions' cmdline currently ignores
any additional arguments and so U-Boot always uses bus 0.
Regions are stored in controller (not on the bus) and therefore to retrieve
controller from the bus, it is needed to call pci_get_controller() which
returns root bus. Because bus 0 is root bus, current code worked fine for
controller 0.
Extend cmdline parser for 'pci regions' to allows specifying bus number,
extend pci_show_regions() code to accept also non-zero bus number and
print bus ranges for which is regions configuration assigned.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Allow this to be used on any arch. Also convert to using macros so that
we can check the CONFIG option in C code.
Signed-off-by: Simon Glass <sjg@chromium.org>
