Replace uImage with ${uimage}.
If uimage is not set, default it to uImage.
Signed-off-by: Andreas Huber <andreas.huber@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
kmvect1 has a UEC2 connection to the piggy board and a UEC0 connection
to the switch MV88E6122. This switch has a connection to a frontport
ethernet interface. The ethernet port used for network booting is
automatically selected by u-boot. If a Piggy is plugged, the Piggy
port is selected (UEC2, eth1). If the Piggy isn't present, the
Frontport is selected (UEC0, eth0).
The switch reset is connected to a GPIO on the PRIO3 board FPGA (GPIO28)
and released at startup.
Signed-off-by: Karlheinz Jerg <karlheinz.jerg@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
For the the kmvect1 board we will also need a functionality to add an
offset to the IVMs MAC address, because these board will have two valid
ethernet ports for debugging purpose. So move the code to an own
function.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
For kmvect1 we need a special solution and for km_arm boards we already
have. So move the common code to the architectur specific file.
Signed-off-by: Karlheinz Jerg <karlheinz.jerg@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
This saves stack and code memory for local copy, and
consumes initialized data memory. For 22 of the 29
kirkwood-based boards, this results in a global saving
of about 30 bytes. For 7 of them, it results in an
increase of 6 to 14 bytes.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
This patch removes 2 small portions of board specific code that are
duplicated with common ARM code and thus unnecessary. These 2 portions
of code concern the mach id that is given by u-boot to the Linux kernel
to identify the system's MACH.
The first one was the possibility to change the MACH thanks to the
'mach_id' enviroment variable. This is possible thanks to the 'machid'
env variable (see arch/arm/lib/bootm.c:boot_jump_linux()).
The seconde one is the setting of the bi_arch_number. This is already
done in arch/arm/lib/board.c:board_init_f() since km_arm.h does #define
CONFIG_MACH_TYPE.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
Acked-by: Prafulla Wadaskar <Prafulla@marvell.com>
On kmcoge5un we faced some serious problems with the memory during
temperature tests. Reason was that we overwrite some registers for
memory settings which have to leave untouched. These where registers
0x20148 , 0x2014c and 0x20154.
So writing these registers is prohibited and this patch removes them
from all km related config files. Even if the problem was only
seen on kmcoge5un.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
Add support for Keymile boards based on mpc8309
(it would be only kmvect1 for now)
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
[#elseif -> #if to allow kmcoge5ne and kmeter1 to build successfully]
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The kmnusa board uses a mv88e6352 switch that is connected to the main
eth interface of the kirkwood. Therefore the switch must be configured
so that the kirkwood's egiga eth inferface can be used.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Cc: Holger Brunck <holger.brunck@keymile.com>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Acked-By: Prafulla Wadaskar <prafulla@marvell.com>
Some boards may differ only in the SDRAM size. This function allows to
fix the size accordingly and we can use the same u-boot binary for both
boards.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
For some reasons we had an own implementaion of dram_init and
dram_init_banksize. This is not needed anymore, use the standard
kirkwood functions instead.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
Acked-By: Prafulla Wadaskar <prafulla@marvell.com>
The fanless boards now have a 7-digit (XXXXX-F) board name. This
triggers a border condition when reading this string in the IVM although
this string is smaller than the currenly read string size, but only by 1
character.
This patch corrects this by changing the size check condition for string
length. It is the same change that was done in the platform for this
same bug.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Stefan Bigler <stefan.bigler@keymile.com>
This patch moves all bootcount implementations into a common
directory: drivers/bootcount. The generic bootcount driver
is now usable not only by powerpc platforms, but others as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Valentin Longchamp <valentin.longchamp@keymile.com>
Cc: Christian Riesch <christian.riesch@omicron.at>
Cc: Manfred Rudigier <manfred.rudigier@omicron.at>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Reinhard Meyer <reinhard.meyer@emk-elektronik.de>
Tested-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Tested-by: Christian Riesch <christian.riesch@omicron.at>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
This patch adds SDRAM detection feature to km82xx boards.
To enable this feature, define CONFIG_SYS_SDRAM_LIST as the initializer
for an array of struct sdram_conf_s.
These structs will expose the bitfields within registers PSDMR and OR1 which
have to be different between configurations; common bitfields will be
defined, as usual, within CONFIG_SYS_PSDMR and CONFIG_SYS_OR1.
If CONFIG_SYS_SDRAM_LIST is not defined, then the usual behavior is retained.
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
This code will also be used before reallocation and during this time we
are not allowed to do these printings.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Prafulla Wadaskar <Prafulla@marvell.com>
Acked-by: Heiko Schocher <hs@denx.de>
Also drop a few files referring to no longer / not yet supported
boards.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Kim Phillips <kim.phillips@freescale.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Jason Jin <jason.jin@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
These functions tried to access two static tables before relocation
(board_early_init_f is executed before relocation). But these static
tables lie in the bss section which is not valid before relocation.
These accesses then overwrote some parts of u-boot binary before it was
relocated. For the kmnusa build, this results in a corrupted important
env variable (bootcmd) but it may be that some other parts of the u-boot
binary are corrupted.
This patch solves this problem by moving all the kw_gpio_* calls to
board_init, which should be early enough in the boot sequence. The only
calls that could not be moved is the one for the SOFT (bitbang) I2C, and
they have been replaced by a direct access to the GPIO dataout Control
register to set the two GPIOs as output.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
Add a function to read the dip_switch on kmcoge5un. If the
switch is set the actual_bank is set to 0 and this SW is
booted.
Signed-off-by: Thomas Herzmann <thomas.herzmann@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
The PCIe FPGAs now have to support 2 resets: one for the non traffic
affecting part (PCIe) and one for the traffic affecting part.
When the FPGA is not reconfigured, we only reset the PCIe part.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
In order to be able to perform board resets without interrupting the
traffic, the configuration of an already properly configured FPGA is
skipped.
This is because some PCIe FPGAs embed some other function that must
continue to work over reset.
It is then the responsibility of the application to trigger a
reconfiguration when needed. This is done by lowering the FPGA_INIT_B
pin for delaying the configuration to u-boot @ next reboot, and then
lower the FPGA_PROGRAM_B signal.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Some very similar #defines for reg addresses are used in a later patch
(managed_switch support for km_arm).
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
This adds a first support of the FPGA download for a PCIe FPGA based
on the BOCO2 CPLD.
This takes place in 3 steps, all done accessing the SPICTRL reg of the
BOCO2:
1) start the FPGA config with an access to the FPGA_PROG bit
2) later in the boot sequence, wait for the FPGA_DONE bit to toggle to 1
for the end of the FPGA configuration (with a timeout)
3) reset the FPGA
4) finally remove the access to its config EEPROM from the FPGA so that
the CPU can update the FPGA configuration when the kernel is running
The boards with a PCIe FPGA but without BOCO2 still are supported.
The config option name is CONFIG_KM_FPGA_CONFIG
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
The additional headerfile is unneeded here, we can use the generic
km_kirkwood.h instead. And we can use the better config option
KM_PIGGY4_88E6061 for the specific features for boards with this
design in km_arm.c.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
Use the generic header km_kirkwood.h and get rid of the
board specific header.
changes for v2: rebased because of changes in other patches
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
For u-boot this board is similar to mgcoge3un. But some differences
are present. We have a different SDRAM on it and therefore a new
SDRAM config file. Additionaly this board has a direct MAC/MAC
connection from the kirkwood to a marvell simple switch without a
phy inbetween, this needs a new configuration for the mvgbe driver.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
This board is similar to portl2, but it has the u-boot environment
in a SPI NOR flash and not in an i2c eeprom like portl2 have.
Some other details:
- IVM EEPROM is at adress: pca9547:70:9
- PCI is enabled
- PIGGY4 is connected via MV88E6352 simple switch. There is no phy
between the simple switch and the kirkwood.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
We overwrite these weak functions from the kirkwood spi code to
use our own method to be able to switch between the SPI NOR and
the NAND flash. This is needed e.g. to update the u-boot. The former
command do_spi_toggle can therefore be removed. And the usage of
this command is removed from the u-boot update command in the
u-boot environment.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
With the new second save argument introduced by the previous patch, all
the calls to the function had to be fixed.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
If the testpin is asserted, first check if a test_bank
variable is defined before trying to boot this
test_bank.
Signed-off-by: Thomas Herzmann <thomas.herzmann@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
On kmcoge5ne we have a dip switch present. If this switch
was switched on the actual_bank is set to 0 and this SW
will be booted.
Signed-off-by: Thomas Herzmann <thomas.herzmann@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
kmcoge5ne starts the post tests if the testpin on
the board was enabled. Currently it does simply a memory
test.
Signed-off-by: Thomas Herzmann <thomas.herzmann@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Enabled application buffers in uboot to allow application chipselect
access in uboot.
Signed-off-by: Stefan Bigler <stefan.bigler@keymile.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The MAC address begins at offset 1.
Signed-off-by: Thomas Herzmann <thomas.herzmann@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This board is a MPC8360 board. Two flashes are present
a NOR flash were u-boot and the u-boot environment is stored
and a NAND flash for the application code. This board has 512MB
SDRAM.
Additionaly we introduce a common km8360.h file and convert kmeter1 to
use this.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Christian Herzig <christian.herzig@keymile.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
If the ram size isn't locked to 2GiB, the get_ram_size() may hang up.
Signed-off-by: Christian Herzig <christian.herzig@keymile.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Add a variable "toolchain" and configure the rootpath
for the nfsargs with this variable.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Wolfgang Denk <wd@denx.de>
Configuring for kmeter1 board...
km83xx_i2c.c: In function 'i2c_make_abort':
km83xx_i2c.c:44:8: warning: variable 'dummy' set but not used [-Wunused-but-set-variable]
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Acked-by: Heiko Schocher <hs@denx.de>
commit b11f53f3 (keymile: Fix Coding style issues for keymile boards)
introduces a bug according the SDRAM initialization for all
km83xx boards.
im->ddr.sdram_cfg |= SDRAM_CFG_MEM_EN;
was replaced with
out_be32(&im->ddr.sdram_cfg, SDRAM_CFG_MEM_EN);
and this is wrong, because this overwrites the intial value
CONFIG_SYS_DDR_SDRAM_CFG.
Signed-off-by: Andreas Huber <andreas.huber@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The common code should be valid for more than one architecture.
Therefore this code was reorganized and moved to the new
file km83xx_i2c.c
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
