As seen on GCC 4.6 Linaro compiler, control_req buffer is not aligned
on 4 byte boundaray causing data aborts in eth_setup -> conf_buf
during dhcp boot over usb_ether. Fix the issue my aligning control_req
buffer using DEFINE_CACHE_ALIGN_BUFFER.
Tested on am335x_evm platform (beaglebone).
Applies on 2013.10-rc1 branch.
Cc: Tom Rini <trini@ti.com>
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Joel Fernandes <joelf@ti.com>
The gadget ethernet driver needs to keep copies of the MAC address (at
both endpoints) as strings so it needs a custom function for validation
of the MAC. It was not however performing a totally correct check and
also was emitting a warning about a set but unused variable. The
solution to both is that after checking the string contents we use the
standard test for a valid MAC.
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Removed DEV_CONFIG_CDC and DEV_CONFIG_SUBSET and replaced it with
CONFIG_USB_ETH_CDC and CONFIG_USB_ETH_SUBSET.
Signed-off-by: Lukasz Dalek <luk0104@gmail.com>
Introduced CONFIG_USB_ETH_CDC and CONFIG_USB_ETH_SUBSET as preparation
for removal DEV_CONFIG_CDC and DEV_CONFIG_SUBSET
Signed-off-by: Lukasz Dalek <luk0104@gmail.com>
PXA25X chips don't support alternate settings so driver uses non-CDC
driver.
But only code defined between DEV_CONFIG_CDC signals that network is up.
This patch is fixing this bug by signaling that network is up after USB
SET_INTERFACE request.
Signed-off-by: Lukasz Dalek <luk0104@gmail.com>
These are all the files which use the API incorrectly but did not get
built using MAKEALL -a powerpc|arm. I have no compiler for them, but
the remaining issues should be far less than without this patch.
Any outstanding issues are left to the maintainers of boards that use
these drivers.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Remove the repeated USB descriptor code and use usbdescriptors.h file.
ch9.h file has been copied from linux and is needed for USB gadget
related work.
Now usbdescriptors.h and ch9.h shall be used together.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Add waiting for receiving Ethernet gadget state on the Windows host
side before dropping pullup, but keep it for debug.
Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
Port USB gadget RNDIS protocol support from linux-2.6.26
(.27 gadget stack actually has composite drivers).
Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
Disconnecting USB gadget with pending interrupt may cause its wrong
handling in the next time when interface will be started again
(especially actual for RNDIS). This interrupt may force the gadget
to queue unexpected response before setup stage.
Despite the fact that such interrupt handled after dropped pullup
also may add pending response, this will not bring to any issues due to
usb_ep_disable (which clears the queue) called on gadget unregistering.
Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
Calling eth_bind at usb_eth_init time causes renaming of the network
device from 'usb_ether' to 'usb0'. Fixing this to keep the first name.
Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
Since the ether may not be the only one usb gadget would be used
in the uboot, it is neccessary to do the register each time the
eth begin to work to make usb gadget driver less confussed when
we want to use two different usb gadget at the same time.
Usb gadget driver could simple ignore the register operation, if
it find the driver has been registered already.
Signed-off-by: Lei Wen <leiwen@marvell.com>
After gadget reinitializaton (after tftp has been done once)
packet_received may become equal to 1 due to nuking OUT_EP
while disabling it in eth_reset_config.
rx_submit called from usb_eth_init queues rx_req first time.
But the first call of usb_eth_recv from NetLoop queues rx_req
again due to packet_received = 1.
The following flow shows the path of functions calls when
this happens:
net/net.c:NetLoop
|
+-net/eth.c:eth_init
| ether.c:usb_eth_init
| |
| +-udc_driver:usb_gadget_handle_interrupts
| | udc_driver:...
| | ether.c:eth_setup
| | ether.c:eth_set_config
| | ether.c:eth_reset_config
| | udc_driver:usb_ep_disable
| | udc_driver:nuke
| | ether.c:rx_complete
| | ether.c: packet_received = 1;
| |
| +-ether.c:rx_submit
| udc_driver:usb_ep_queue --- The first time when rx_req is queued
|
+-net/eth.c:eth_rx
ether.c:usb_eth_recv
|
+-udc_driver:usb_gadget_handle_interrupts
| udc_driver:... --- no interrupts, returning
+-ether.c: if (packet_received) { ...
ether.c:rx_submit
udc_driver:usb_ep_queue --- The second time!
Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
Remove and fix needless and destructive operations with tx/rx_req.
1) 'req' in rx_complete is always not NULL and always equals to rx_req
2) Free allocated tx_req if rx_req allocation has failed
3) Do not zero out tx/rx_req in usb_eth_init, leave this for
eth_reset_config which will be called at the next use of usb0
4) Additional check in usb_eth_recv is not required
Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
Fixes most of checkpatch warnings and errors in USB gadget stack.
The most frequently encountered problems are:
1) "(foo*)", "foo * bar", "foo* bar"
2) C99 // comments
3) No spaces before/after/around '?', ':', '=', '==', ',', '&', '('
4) Spaces before '['
5) Spaces between function names and '('
6) Block braces in wrong places
7) Spaces before tabs
8) Macros with complex values not enclosed in parenthesis
9) Multiline comments start just after /*
Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
The patch removes an endless loop in the usb_eth_send
if the tx_complete is not called before going
in the loop. The driver interrupt routine is called
allowing the driver to check if the TX is completed.
Signed-off-by: Stefano Babic <sbabic@denx.de>
The buffer for the status request must be word aligned
because it is accessed with 32 bit pointer in the
eth_status_complete function.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Fix potential oops on rare error path.
The patch is based on commit e7b13ec9235b9fded90f826ceeb8c34548631351
(done by David Brownell <david-b@pacbell.net>) from linux-2.6.git.
Description of the issue taken from linux kernel bugzilla:
(https://bugzilla.kernel.org/show_bug.cgi?id=9594)
The potential error can be tracked down as follows:
(1) line 807: let the second conjunct on the "if" statment be false
meaning "dev->status_ep" is null. This means the "if" evaluates
to false.
follow thru the code until...
(2) line 808: usb_ep_disable(dev->status_ep) passes in a null argument,
however "usb_ep_disable" cannot handle that:
(from include/linux/usb/gadget.h)
191 static inline int
192 usb_ep_disable (struct usb_ep *ep)
193 {
194 return ep->ops->disable (ep);
195 }
--
Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
Fix possible oops on stat_req->buf initialization and fix ep0 and
status_ep confusion (last one is just intended for stat_req keeping).
Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
Signed-off-by: Stefano Babic <sbabic@denx.de>
Fix in_ep and out_ep confusion (rx_req was allocated from out_ep, not
from in_ep) and add lost dev->req freeing.
Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
Add lost 'qmult' definition for High Speed devices and make it
configurable through CONFIG_USB_ETH_QMULT.
Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
