- Fix some issues Coverity Scan reported in IPv6, SPL EXTn support fix,
two small bootstd fixes, one Kconfig dependency fix, and fix booting
on Pinephone Pro
CID 453851 : sprintf() shouldn't copy from/to tmp
CID 436278 : DHCP6 option_len should be checked before use
Signed-off-by: Sean Edmond <seanedmond@microsoft.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Add the RAM_ROCKCHIP_LPDDR4 to fix the Pinephone Pro booting.
When the configs were updated in 26f92be07e it somehow broke
the PPP boot process so let's fix it.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
CC: Jagan Teki <jagan@edgeble.ai>
CC: Kever Yang <kever.yang@rock-chips.com>
Using relative path in a /boot/extlinux/extlinux.conf file fails to load
linux kernel.
Using a /boot/extlinux/extlinux.conf file:
LABEL test
LINUX ../linux/Image
Result in following error:
Retrieving file: ../linux/Image
Skipping test for failure retrieving kernel
Boot failed (err=-14)
However, using sysboot cmd successfully load kernel using same file:
sysboot mmc 1:1 any ${scriptaddr} /boot/extlinux/extlinux.conf
Retrieving file: /boot/extlinux/../linux/Image
Fix relative path using bootmeth extlinux by supplying bootfile path
instead of subdir path in the call to pxe_setup_ctx, same as done in the
sysboot command.
Fixes: 31aefaf89a ("bootstd: Add an implementation of distro boot")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move BOOTSTD_FULL down in the file so that it can be enabled only when
BOOTSTD is enabled. This prevents a build error if BOOTSTD is disabled
but BOOTSTD_FULL is enabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
The rtl8169 driver uses calls to dm_pci_bus_to_phys,
which are compiled under CONFIG_PCI.
Without CONFIG_PCI, this happens:
drivers/net/rtl8169.o: in function `rtl_recv_common':
drivers/net/rtl8169.c:555: undefined reference to `dm_pci_bus_to_phys'
It is only natural that this driver depends on CONFIG_PCI then.
The device does not work connected in another way anyway, and the driver
does not assume anything else at this moment.
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Since commit 9905cae65e ("fs: ext4: check the minimal partition size
to mount"), a valid size needs to be provided when mounting
an ext filesystem. Fix the spl ext driver to use the parition size
instead of 0 when mounting the filesystem.
Signed-off-by: Mayuresh Chitale <mchitale@ventanamicro.com>
Export the already existing DPNI and DPMAC counters through the newly
added callbacks.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add a new option to the 'net' command which can be used to dump network
statistics.
To do this, 3 new callbacks are added to the eth_ops structure:
.get_sset_count(), .get_strings(), .get_stats(). These callbacks
have the same functions as in Linux: to return the number of counters,
the strings which describe those counters and the actual values.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The ldpaa_eth driver already had a DPMAC statistics dump, this patch
extends the list of stats and adds a bit more structure to the code.
For a bit more context, the DPAA2 u-boot software architecture uses a
default network interface object - a DPNI - which, at runtime, will get
connected to the currently used DPMAC object.
Each time the .stop() eth callback is called, the DPMAC is destroyed
thus any previous counters will get lost.
As a preparation for the next patches, we add a software kept set of
DPMAC counters which will get updated before each destroy operation
takes place.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The ldpaa_eth driver already had a DPNI statistics dump, this patch
extends the list of stats and adds a bit more structure to the code.
For a bit more context, the DPAA2 u-boot software architecture uses a
default network interface object - a DPNI - which, at runtime, will get
connected to the currently used DPMAC object.
Each time the .stop() eth callback is called, the DPNI is reset to its
original state, including its counters.
As a preparation for the next patches, we add a software kept set of
DPNI counters which will get updated before each reset operation takes
place.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
In order to simplify code, dpni_statistics can be written as a union.
Using the raw accessors we can just loop through all the statistics from
a page without trying to access each an every one independently.
Make this change to a union.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Each MC commands has a specific predefined memory layout that gets
interpreted by the firmware. The dpmac_get_counters() API memory layout
is wrong, thus the results returned by the command are incorrect.
Fix this by updating the offset of the counter field.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The variable 'node' was already invalid, so using it for further
lookup will not work.
Signed-off-by: Marcus Comstedt <marcus.comstedt@requtech.se>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Currently we only read the pcr updates once on test_tpm2_pcr_read().
It turns out that the tpm init sequence of force_init() which consists
of:
- tpm2 init
- tpm2 startup TPM2_SU_CLEAR
- tpm2 self_test full
- tpm2 clear TPM2_RH_LOCKOUT
also counts as an update. Running this in the console verifies the
update bump
=> tpm2 init
=> tpm2 startup TPM2_SU_CLEAR
=> tpm2 self_test full
=> tpm pcr_read 10 $loadaddr
PCR #10 content (28 known updates):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
=> tpm2 clear TPM2_RH_LOCKOUT
=> tpm pcr_read 10 $loadaddr
PCR #10 content (29 known updates):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
=>
With the recent changes of replacing 'tpm2 init' with 'tpm2 autostart'
we end up always running the full init. The reason is 'tpm init'
returns -EBUSY if the tpm is already open, while 'tpm autostart' handles
ths gracefully and continues with the initialization. It's worth noting
that this won't affect the device functionality at all since
retriggering the startup sequence and selftests has no side effects.
Instead of relying on the initial value, reread the 'known updates'
just before updating the PCR to ensure we read the correct values
before testing
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Instead of copy pasting the commands needed to start a TPM consisting
of:
- tpm init
- tpm startup TPM2_SU_CLEAR
- tpm2 self_test full
use the newly added 'autostart' which does the same thing and simplify
our python scripts
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
For a TPM device to be operational we need to initialize it and
perform its startup sequence. The 'tpm init' command currently calls
tpm_init() which ends up calling the ->open() per-device callback and
performs the initial hardware configuration as well as requesting
locality 0 for the caller. There no code that currently calls
tpm_init() without following up with a tpm_startup() and tpm_self_test_full()
or tpm_continue_self_test().
So let's add a 'tpm autostart' command and call tpm_auto_start() which
leaves the device in an operational state.
It's worth noting that calling tpm_init() only, doesn't allow a someone
to use the TPM since the startup sequence is mandatory. We always
repeat the pattern of calling
- tpm_init()
- tpm_startup()
- tpm_self_test_full() or tpm_continue_self_test()
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
For lockstep mode, cpu_release function is expecting to execute
on R5 core 0, if there is attempt to pass other than R5 core 0,
through an error saying "Lockstep mode should run on R5 core 0 only".
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20230608032152.980-3-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
While invoking "zynqmp tcminit mode" command (which is invalid command)
on U-Boot, it just works. Check the mode param, if it is valid then
only initialize the TCM.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20230608032152.980-2-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
This patch adds the PCIe controller driver for the Xilinx / AMD ZynqMP
NWL PCIe Bridge as root port. The driver source is partly copied from
the Linux PCI driver and modified to enable usage in U-Boot (e.g.
simplified and interrupt support removed).
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Pali Rohár <pali@kernel.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20230525094918.111949-1-sr@denx.de
Signed-off-by: Michal Simek <michal.simek@amd.com>
Process errors from command via cmd_process_error() as is done on Versal.
When internal function returns different number then CMD_RET_SUCCESS(0),
CMD_RET_FAILURE(1) or CMD_RET_USAGE(-1) shell react on these errors by
throwing an error like
"exit not allowed from main input shell." that's why use
cmd_process_error() to make sure that error code is all the time correct.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/d511935ba10daf95c70996fae6e6ffc374efffa0.1685618464.git.michal.simek@amd.com
The Xilinx ZynqMP SoC has a hardened display pipeline named DisplayPort
Subsystem. It includes a buffer manager, blender, an audio mixer and a
DisplayPort source controller (transmitter). The DisplayPort controller can
source data from memory (non-live input) or the stream (live input). The
DisplayPort controller is responsible for managing the link and physical
layer functionality. The controller packs audio/video data into transfer
units and sends them over the main link. The link rate and lane counts can
be selected based on the application bandwidth requirements. The
DisplayPort pipeline consists of the DisplayPort direct memory access (DMA)
for fetching data from memory. The DisplayPort DMA controller (DPDMA)
supports up to six input channels as non-live input.
This driver supports the DisplayPort Subsystem and implements
1)640x480 resolution
2)RGBA8888 32bpp format
3)DPDMA channel 3 for Graphics
4)Non-live input
5)Fixed 5.4G link rate
6)Tested on ZCU102 board
There will be additional work to configure GT lines based on DT, higher
resolutions, support for more compressed video formats, spliting code to
more files, add support for EDID, audio support, using clock framework for
all clocks and in general code clean up.
Codevelop-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/5c1567b63d0280dacc7efba2998857c399c25358.1684312924.git.michal.simek@amd.com
Add support for RGBA8888 32bpp format where pixels are picked in
32-bit integers, where the colors are stored in memory such that
R is at lowest address, G after that, B after that, and A last.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/aa1de54b7d4ff46df6858f76d52634e0c5c71a4a.1684312924.git.michal.simek@amd.com
Store the driver data in the data section to make the data usable before
relocation. Additionally mark the driver data static to restrict the
access.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Link: https://lore.kernel.org/r/20230523124215.30915-5-stefan.herbrechtsmeier-oss@weidmueller.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Move the permission to change a config object message from
zynqmp_pmufw_load_config_object function to zynqmp_pmufw_node function
to simplify the code and check the permission only if required.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Link: https://lore.kernel.org/r/20230523124215.30915-4-stefan.herbrechtsmeier-oss@weidmueller.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Remove the redundant child device bind from the driver bind function and
rely on the post_bind of the class which calls the same function.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Link: https://lore.kernel.org/r/20230523124215.30915-2-stefan.herbrechtsmeier-oss@weidmueller.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Return a common -EACCES error value instead of a positive private error
value XST_PM_NO_ACCESS (2002) in zynqmp_pmufw_load_config_object
function if the config object is not loadable to simplify the error
checking.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Link: https://lore.kernel.org/r/20230523124215.30915-1-stefan.herbrechtsmeier-oss@weidmueller.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Production version restarting platform version field from 0 that's why add
new calculation to be able to use different DT for these platforms.
Requested DT names for production silicons for IPP/SPP and EMU platform are
versal-net-ipp-rev2.0.dts and versal-net-emu-rev2.0.dts.
If platform version increase numbers revision can be even higher.
As of today platform version is 2 that's why expected is rev2.2.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/691e166b3cf2643d7edf482bda5500163eecb35a.1684311689.git.michal.simek@amd.com
For sf commands, when '0' length is passed for erase, update, write or
read, there might be undesired results. Ideally '0' length means nothing to
do.
So print 'ERROR: Invalid size 0' and return cmd failure when length '0' is
passed to sf commands. Same thing applies for nand commands also.
Example:
ZynqMP> sf erase 0 0
ERROR: Invalid size 0
ZynqMP> sf write 10000 0 0
ERROR: Invalid size 0
ZynqMP> sf read 10000 0 0
ERROR: Invalid size 0
ZynqMP> sf update 1000 10000 0
ERROR: Invalid size 0
ZynqMP>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230516115236.22458-1-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
