Fix:
mpc8568mds.c: In function 'local_bus_init':
mpc8568mds.c:150:7: warning: variable 'lbc_hz' set but not used [-Wunused-but-set-variable]
mpc8568mds.c: In function 'pib_init':
mpc8568mds.c:271:11: warning: variable 'orig_i2c_bus' set but not used [-Wunused-but-set-variable]
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix:
mpc8548cds.c: In function 'local_bus_init':
mpc8548cds.c:87:7: warning: variable 'lbc_hz' set but not used [-Wunused-but-set-variable]
mpc8548cds.c: In function 'lbc_sdram_init':
mpc8548cds.c:121:7: warning: variable 'cpu_board_rev' set but not used [-Wunused-but-set-variable]
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix:
pixis.c: In function 'strfractoint':
pixis.c:383:6: warning: variable 'intarr_len' set but not used [-Wunused-but-set-variable]
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix:
cds_pci_ft.c: In function 'cds_pci_fixup':
cds_pci_ft.c:31:12: warning: variable 'tmp' set but not used [-Wunused-but-set-variable]
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
For ICS307-02, there is one general expression to generate SYSCLK:
CLK1Frequency = InputFrequency * 2 * (VDW + 8) / ((RDW + 2) * OD)
If we want the required frequency for SYSCLK, we must find one solution
to generate this frequency, this solution includes VDW, RDW and OD.
For OD, there are only eight option value: 10, 2, 8, 4, 5, 7, 3, 6.
For RDW, the range is 1 to 127.
For VDW, the range is 4 to 511.
First, we use one OD, RDW and required SYSCLK to calculate the VDW,
if VDW is in it's range, we will calculate the CLK1Frequency with
the OD, RDW and VDW calculated, and we will check this percent
(CLK1Frequency / required SYSCLK), and the precision is 1/1000.
if the percent is less than 1/1000, we think the CLK1Frequency is we want.
Otherwise, We will continue to calculate it with the next OD and RDW.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Include call to usb device-fixup only when CONFIG_HAS_FSL_DR_USB is
defined for the platform - P1020RDB, P1010RDB, P1020-PC
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add board_eth_init(). PCIe network card is also supported.
Put RGMII init after tsec_eth_init().
Skip initializing eTSEC3 and eTSEC4 with Carrier boards prior to ver 1.3.
Signed-off-by: Ebony Zhu
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
TBI PHY address (TBIPA) register has been set in general frame manager
phy init funciton dtsec_init_phy() in drivers/net/fm/eth.c
So remove the duplicate code on QorIQ frame manager Ethernet related
platforms, which include Hydra board, P4080DS board and P2041rdb board.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'master' of git://git.denx.de/u-boot-arm:
Arm: re-introduce the MACH_TYPE_XXXXXX for EB_CPUX9K2 board
arm: jadecpu: Readd MACH_TYPE_JADECPU
at91: defined mach-types for otc570 board in board config file
at91: defined mach-types for meesc board in board config file
mx31pdk: Enable D and I caches
ehci-mxc: remove incorrect comment
README: Fix supported i.MX SoC list for CONFIG_MXC_SPI
mx53: Turn off child clocks before reconfigure perclk_root
qong: enable support for compressed images
imx: imx31_phycore.h: fix checkpatch warnings
vision2: Remove unused get_board_rev function
mx53smd: Remove unused get_board_rev function
mx53ard: Remove unused get_board_rev function
mx53evk: Remove unused get_board_rev function
mx53evk: Add RTC support
mx53loco: Remove unused get_board_rev function
mx53evk: Remove unneeded '1' from mx53evk.h
OMAP3: mvblx: Initial support for mvBlueLYNX-X
ARM: dig297: Define MACH_TYPE_OMAP3_CPS and CONFIG_MACH_TYPE
omap3: mem: Move comments next to definitions
omap3: mem: Clean-up whitespaces
omap3: mem: Define and use common macros
Davinci: ea20: added PREBOOT to configuration
Davinci: ea20: added I2C support
Davinci: ea20: added video support
VIDEO: davinci: add framebuffer to da8xx
ARM: Davinci: added missing registers to hardware.h
Davinci: ea20: add gpios for LCD backlight control
Davinci: ea20: add gpio for keeping power on in board_late_init
Davinci: ea20: Add default U-Boot environment
Davinci: ea20: Add early init to get early output from console
Davinci: ea20: Add NAND support
Davinci: ea20: set GPIOs to hold MII-Phy in reset and set UART0-Switch for console
Davinci: ea20: set console on UART0
arm, davinci: add cam_enc_4xx support
arm926ejs, davinci: add missing spi defines for dm365
arm926ejs, davinci: add cpuinfo for dm365
arm, davinci: add lowlevel function for dm365 soc
arm, davinci: add header files for dm365
spl, nand: add 4bit HW ecc oob first nand_read_page function
arm, davinci: add support for new spl framework
spl: add option for adding post memory test to the SPL framework
net, davinci_emac: make clock divider in MDIO control register configurable
arm, usb, davinci: make USBPHY_CTL register configurable
usb, davinci: add enable_vbus() weak function
omap3evm: fix errors caused by multiple definitions
omap3evm: Add (quick) configuration for NAND only
omap3evm: Add (quick) configuration for MMC/SD only
omap3evm: move common config options to new file
omap3evm: Prepare to split configuration
omap3evm: Reorder related config options
omap/spl: actually enable the console
davinci_emac: compilation fix, phy is array now
omap3evm: Set environment variable 'ethaddr'
arm, arm926: fix missing symbols in NAND_SPL mode
arm, davinci: Add function lpsc_syncreset()
arm, davinci: replace CONFIG_PRELOADER with CONFIG_SPL_BUILD
arm/km: portl2 environment address update to P1B
arm/km: adapt bootcounter evaluation
arm/km: enable jffs2 cmds
arm/km: trigger reconfiguration for the Xilinx FPGA
arm/km: add boardid and hwkey to kernel command line
ARM: Reintroduce MACH_TYPE_KM_KIRKWOOD for keymile ARM boards
netspace_v2: enable I2C EEPROM support
netspace_v2: fix SDRAM configuration
armada100: define CONFIG_SYS_CACHELINE_SIZE
pantheon: define CONFIG_SYS_CACHELINE_SIZE
kirkwood: define CONFIG_SYS_CACHELINE_SIZE
kirkwood: drop empty asm-offsets.s file
arm/km/mgcoge3un: enhance "waitforne" feature
arm/km: add variable waitforne to mgcoge3un
gplugD: Fix for error:MACH_TYPE_SHEEVAD undeclared
ARM: dreamplug: fix compilation
ARM: DockStar: fix compilation
ARM: netspace_v2: fix warnings
am335x: Drop board_sysinfo struct
am335x: Temporarily add MACH_TYPE define
misc:pmic:samsung Enable PMIC driver at C210 Universal target
dcache:s5p CONFIG_SYS_CACHELINE_SIZE added for s5p UNIVERSAL C210 target
dcache:s5p CONFIG_SYS_CACHELINE_SIZE added for s5p GONI target
smdkv310: use macro for mmc data read function address
smdkv310: use spl framework for mmc spl
SMDKV310: use get_ram_size() to validate dram size
SMDKV310: Initialize board id using CONFIG_MACH_TYPE
ORIGEN : use absolute paths and fix tool naming
ORIGEN : enable device tree support
MX25: tx25: Fix building due to missing MACH_TYPE
mx31: Add board support for HALE TT-01
mx31: add ESD control registers
mx31: define pins and init for UART2 and CSPI3
MX35: add support for flea3 board
MX51: vision2: add MACH_TYPE in config file
vision2: Remove unused header file
mx51evk: Remove unused get_board_rev function
mx51evk: Remove unneeded '1' from mx51evk.h
I2C: Fix mxc_i2c.c problem on imx31_phycore
mx35pdk: Add RTC support
mx51evk: Use GPIO API for configuring the IOMUX
mx51evk: Add RTC support
rtc: Make mc13783-rtc driver generic
qong: remove unneeded IOMUX settings
qong: Use mx31_set_gpr to setup USBH2 pins
mx31: Introduce mx31_set_gpr function
mx31pdk: Add MC13783 PMIC support
qong: remove unneeded "1" from qong.h
misc: pmic: fix regression in pmic_fsl.c (SPI)
mx5 configs: CONFIG_PRIME should really be CONFIG_ETHPRIME
MX35: Drop unnecessary prototypes from imx-regs.h
I2C: added I2C-2 and I2C-3 to MX35
MX35: factorize common assembly code
MX35: add reset cause as provided by other i.MX
MX35: add pins definition for UART3
MX35: added ESDC structure to imx-regs
* 'master' of git://git.denx.de/u-boot-coldfire:
ColdFire: The EB+MCF-EV123 boards config update
ColdFire: Fix the compile issue for M52277
ColdFire:Moving the remaining coldfire boards to boards.cfg
Fix:
mpc8266ads.c: In function 'initdram':
mpc8266ads.c:278:9: warning: variable 'spd_size' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
After commit 327474f854, the
M52277EVB_stmicro configuration fail to build. Fix it by moving
the env outside the flash and update the lds file.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
No board information is passed for MX53EVK, so remove get_board_rev function.
Cc: Jason Liu <r64343@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Jason Liu <r64343@freescale.com>
No board information is passed for MX53LOCO, so remove get_board_rev function.
Cc: Jason Liu <r64343@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Jason Liu <r64343@freescale.com>
The new MPC8360EMDS board supports 512MB DDR since 2008.
For 512MB DDR:
BAT0 is used for the first 256MB memory, BAT4 is used for the second
256MB memory and the address space of SDRAM follows the DDR, so if the
size of DDR is 256MB, the BAT4 will be used for SDRAM and if the size of
DDR is 512MB, the BAT4 will be used for the second 256MB memory and
there is no BAT for SDRAM.
Therefore, if the size of DDR is 512MB, this patch will use BAT6 for
SDRAM and BAT5 will be used for PCI MEM to replace the BAT6 after the
codes relocates to the DDR.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
CC: Kim Phillips <kim.phillips@freescale.com>
Rename CONFIG_SYS_DDR_CONFIG to include which CS it is configuring
Cleanup the setting of the csnbds to respect the setting of
CONFIG_SYS_DDR_SDRAM_BASE
Use __ilog2 instead of writing the code to compute it
Disable unused CS configs
Ensure ddrlaw.bar is configured
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
GPIO API provides mxc_request_iomux function for setting the IOMUX mode.
Use this function instead of directly writing to the IOMUX register.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Add MC13783 PMIC support.
Tested by using the 'date' command, which reads the MC13783 RTC registers:
MX31PDK U-Boot > date
Date: 1970-01-01 (Thursday) Time: 2:22:35
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* 'master' of git://git.denx.de/u-boot-arm:
ARM: Add Calxeda Highbank platform
dkb: make mmc command as default enabled
Marvell: dkb: add mmc support
ARM: pantheon: add mmc definition
davinci: remove config.mk file from the sources
ARM:AM33XX: Add support for TI AM335X EVM
ARM:AM33XX: Added timer support
ARM:AM33XX: Add emif/ddr support
ARM:AM33XX: Add clock definitions
ARM:AM33XX: Added support for AM33xx
omap3/emif4: fix registers definition
davinci: remove obsolete macro CONFIG_EMAC_MDIO_PHY_NUM
davinci: emac: add support for more than 1 PHYs
davinci: emac: add new features to autonegotiate for EMAC
da850evm: Move LPSC configuration to board_early_init_f()
omap4_panda: Build in cmd_gpio support on panda
omap: Don't use gpio_free to change direction to input
mmc: omap: Allow OMAP_HSMMC[23]_BASE to be unset
OMAP3: overo : Add environment variable optargs to bootargs
OMAP3: overo: Move ethernet CS4 configuration to execute based on board id
OMAP3: overo : Use ttyO2 instead of ttyS2.
da830: add support for NAND boot mode
dm36x: revert cache disable patch
dm644X: revert cache disable patch
devkit8000: Add malloc space
omap: spl: fix build break due to changes in FAT
OMAP3 SPL: Provide weak omap_rev_string
omap: beagle: Use ubifs instead of jffs2 for nand boot
omap: overo: Disable pull-ups on camera PCLK, HS and VS signals
omap: overo: Configure mux for gpio10
SPL: Add DMA library
omap3: Add interface for omap3 DMA
omap3: Add DMA register accessors
omap3: Add Base register for DMA
arm, davinci: add missing LSPC define for MMC/SD1
U-Boot/SPL: omap4: Make ddr pre-calculated timings as default.
DaVinci: correct MDSTAT.STATE mask
omap4: splitting padconfs into common, 4430 and 4460
omap4: adding revision detection for 4460 ES1.1
omap4: replacing OMAP4_CONTROL with OMAP4430_CONTROL
gplug: fixed build error as a result of code cleanup patch
kirkwood_spi: add dummy spi_init()
gpio: mvmfp: reduce include platform file
ARM: orion5x: reduce dependence of including platform file
serial: reduce include platform file for marvell chip
ARM: kirkwood: reduce dependence of including platform file
ARM: armada100: reduce dependence of including platform file
ARM: pantheon: reduce dependence of including platform file
Armada100: Add env storage support for Marvell gplugD
Armada100: Add SPI flash support for Marvell gplugD
Armada100: Add SPI support for Marvell gplugD
SPI: Add SPI driver support for Marvell Armada100
dreamplug: initial board support.
imx: fix coding style
misc: pmic: drop old Freescale's pmic driver
MX31: mx31pdk: use new pmic driver
MX31: mx31ads: use new pmic driver
MX31: mx31_litekit: use new pmic driver
MX5: mx53evk: use new pmic driver
MX5: mx51evk: use new pmic driver
MX35: mx35pdk: use new pmic driver
misc: pmic: addI2C support to pmic_fsl driver
misc: pmic: use I2C_SET_BUS in pmic I2C
MX5: efikamx/efikasb: use new pmic driver
MX3: qong: use new pmic driver
RTC: Switch mc13783 to generic pmic code
MX5: vision2: use new pmic driver
misc: pmic: Freescale PMIC switches to generic PMIC driver
misc:pmic:samsung Enable PMIC driver at GONI target
misc:pmic:max8998 MAX8998 support at a new PMIC driver.
misc:pmic:core New generic PMIC driver
mx31pdk: Remove unneeded config
mx31: provide readable WEIM CS accessor
MX51: vision2: Set global macros
I2C: Add i2c_get/set_speed() to mxc_i2c.c
ARM: Update mach-types
devkit8000: Add config to enable SPL MMC boot
devkit8000: protect board_mmc_init
arm, post: add missing post_time_ms for arm
cosmetic, post: Codingstyle cleanup
arm, logbuffer: make it compileclean
tegra2: Enable MMC for Seaboard
tegra2: Add more pinmux functions
tegra2: Rename PIN_ to PINGRP_
tegra2: Add more clock functions
tegra2: Clean up board code a little
tegra2: Rename CLOCK_PLL_ID to CLOCK_ID
mpc8610hpcd.c: In function 'misc_init_r':
mpc8610hpcd.c:79: warning: format '%02lx' expects type 'long unsigned int', but
argument 2 has type 'int'
mpc8610hpcd.c:86: warning: format '%02lx' expects type 'long unsigned int', but
argument 2 has type 'int'
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Mike Frysinger <vapier@gentoo.org>
diu.c: In function 'diu_set_pixel_clock':
diu.c:77: warning: format '%lu' expects type 'long unsigned int', but argument 2
has type 'u32'
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Mike Frysinger <vapier@gentoo.org>
mpc5121ads.c: In function 'misc_init_r':
mpc5121ads.c:256: warning: format '%02lx' expects type 'long unsigned int', but
argument 2 has type 'int'
mpc5121ads.c:263: warning: format '%02lx' expects type 'long unsigned int', but
argument 2 has type 'int'
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Mike Frysinger <vapier@gentoo.org>
This renames BOARD_LATE_INIT to CONFIG_BOARD_LATE_INIT.
Along the way it removes some leftover
#define BOARD_LATE_INIT 1
and adds some basic documentation for board specific
callbacks in README.
Signed-off-by: Helmut Raiger <helmut.raiger@hale.at>
Acked-by: Stefano Babic <sbabic@denx.de>
Fix checkpatch warning and errors in several i.MX related files.
While at it also address a checkpatch warning at arch/arm/cpu/armv7/mx5/soc.c
regarding the usage of extern in a C file.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Switch to new pmic generic driver.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Jason Liu <jason.hui@linaro.org>
Acked-by: Jason Liu <jason.hui@linaro.org>
setup_weimcs() and some macros are added to support the setup
for i.MX31 WEIM chip selects. As a compromise between verbosity
and readability an ASCII-art'ish bit comment is used instead of
bitfields.
All i.MX31 boards have been patched to use this approach using a
helper program to verify the changes.
Signed-off-by: Helmut Raiger <helmut.raiger@hale.at>
Acked-by: Stefano Babic <sbabic@denx.de>
Seems people fixed their files to use libfoo.o, but didn't actually
update the creation targets to use $(cmd_link_o_target). Update the
rest of the Makefile's found with grep.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Tested-by: Simon Glass <sjg@chromium.org>
There are several mdelay() definitions in the driver and
board code. Remove them all and provide a common mdelay()
in lib/time.c.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
* 'master' of git://git.denx.de/u-boot-mpc85xx:
mpc85xx: Add inline GPIO acessor functions
powerpc/85xx: wait for alignment before resetting SERDES RX lanes (SERDES9)
powerpc/85xx: Fix P2020DS booting
powerpc/85xx: Update USB device tree status based on pin settings
fdt: Add new fdt_set_node_status & fdt_set_status_by_alias helpers
powerpc/85xx: Add support for RMan LIODN initialization
powerpc/85xx: Update device tree handling for SRIO
powerpc/85xx: Update setting of SRIO LIODNs
fm: Don't allow disabling of FM1-DTSEC1
fm-eth: Don't mark the MAC we use for MDIO as disabled in device tree
The work-around for P4080 erratum SERDES9 says that the SERDES receiver
lanes should be reset after the XAUI starts tranmitting alignment signals.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
A temp variable was used but not declared, with CONFIG_SYS_DRAMSZ1
defined. This variable is now declared in the functione when needed.
Signed-off-by: Stany MARCEL <stany.marcel@novasys-ingenierie.com>
The spa, stm, int, 32 and 16 linking files are identical so there is
no need to differentiate them. A single lds file is now used, and
_config rule are simplified.
Signed-off-by: Stany MARCEL <stany.marcel@novasys-ingenierie.com>
Lds files cleened to remove multiple defined section and modified to
be compliant with --gc-sections added for ColdFire platform in a
previous patch.
Signed-off-by: Stany MARCEL <stany.marcel@novasys-ingenierie.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
The following commit removed the code that set odt_rd_cfg and
odt_wr_cfg. With out this code P2020DS board will not boot:
commit 712cf7ab0b
Author: York Sun <yorksun@freescale.com>
Date: Mon Oct 3 09:19:53 2011 -0700
powerpc/mpc8xxx: Merge entries in DDR speed table
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add common function fdt_set_node_status() to assist in various locations
that we set a nodes status. This function utilizes the status values
that are part of the EPAPR spec (on power.org).
fdt_set_status_by_alias() is based on fdt_set_node_status() but uses an
alias string to identify the node to update.
We also add some shortcut functions to help the common cases of setting
"okay" and "disabled":
fdt_status_okay()
fdt_status_disabled()
fdt_status_okay_by_alias()
fdt_status_disabled_by_alias()
Finally, we fixup the corenet_ds ethernet code which previously had
a function by the same name that can be replaced with the new helpers.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Gerald Van Baren <vanbaren@cideas.com>
The top level Makefile does not do any recursion into subdirs when
cleaning, so these clean/distclean targets in random arch/board dirs
never get used. Punt them all.
MAKEALL didn't report any errors related to this that I could see.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
- Rework tlb and law tables.
- PCI2 is not available on MPC8548CDS, so remove it.
- Move the memory map to the board config file.
- Rewrite the board info according to the manual.
- Remove unnecessary macros and redefine some macros to align with other boards.
- Fix some typos.
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
MPC8536 Rev 1.0 silicon have NMG_eSDHC118 erratum, so that the SDHC write
protected pin polarity does not follow the SD card standard in MPC8536
Rev 1.0 silicon.
The MPC8536DS board invert the SDHC_WP pin as a workaround. However, this
silicon erratum has been fixed in Rev 1.1, So need invert the SDHC_WP
polarity again when use the MPC8536 Rev1.1 and greater on MPC8536DS board.
Signed-off-by: Xie Xiaobo <r63061@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
1. The SD_DATA[4:7] signals are shared with the SPI chip selects on 8536DS,
so don't set MPC85xx_PMUXCR_SD_DATA that config eSDHC data bus-width
to 4-bit and enable SPI signals.
2. Add eSPI controller and SPI-FLASH definition.
Signed-off-by: Xie Xiaobo <r63061@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
It is not necessary to keep multiple entries for the same setting in DDR
speed tables. Merge them for smaller tables. Also restructure the tables
for smaller size. Cleanup some typedefs.
Enforce strict checking for speed table. If DIMM is running at higher than
known speed, try to use the highest speed setting. If rank is unknown, it
has to panic.
Removed ODT overriding for P2020DS as it is not necessary.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
