Normally, when NET is enabled, CMD_NET will then be enabled and in turn
NETDEVICES will (likely) be enabled via imply. However, if we disable
CMDLINE in a defconfig we now no longer get CMD_NET enabling NETDEVICES
for us. This suggestion (as an imply is) really isn't about the network
commands but network itself and is a legacy of how intertwined
NET/CMD_NET were historically. Move this over to the NET entry instead
where it is a more logical fit.
Reported-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
This adds the URI device path option for 'boot add' subcommand.
User can add the URI load option for downloading ISO image file
or EFI application through network. Currently HTTP is only supported.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Current wget takes the target uri in this format:
"<http server ip>:<file path>" e.g.) 192.168.1.1:/bar
The http server ip address must be resolved before
calling wget.
This commit adds the utility function runs wget with dhs.
User can call wget with the uri like "http://foo/bar".
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
This introduces the valid range check to store the received
blocks using lmb. The same logic is implemented in tftp.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
While bringinp up a new board without the MAC fuses programmed,
the following error message was observed:
Error: ethernet@30bf0000 address not set.
Improve the error message to make it clearer the reason of
the failure.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Add an option to trace all packets send/received. This can be helpful when
debugging protocol issues, as the packets can then be imported into
wireshark [1] and analyzed further.
[1] https://www.wireshark.org/docs/wsug_html_chunked/ChIOImportSection.html
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
There is no reason to setup ROM source if read_rom_hwaddr hook doesn't
exist or reading mac address fails. It is ending up with confusion about
mac address source.
It is nicely visible if you put mac address to DT as
local-mac-address = [ff ff ff ff ff ff];
but also save ethaddr to variables
setenv -f ethaddr 02:18:31:7e:3e:01
Before this patch U-Boot prints that source is ROM
Address in ROM is ff:ff:ff:ff:ff:ff
Address in environment is 02:18:31:7e:3e:01
After that source is DT:
Address in DT is ff:ff:ff:ff:ff:ff
Address in environment is 02:18:31:7e:3e:01
Signed-off-by: Michal Simek <michal.simek@amd.com>
RFC 5970 states that OPT_BOOTFILE_PARAM (option 60) can be
multiple parameters that start with a 16-bit length field followed
by the parameter. For example:
[ param-len 1 (16-bits) ] [ parameter 1 (variable length) ]
This fix ensure we're considering "param-len 1" in the parsing.
Signed-off-by: Sean Edmond <seanedmond@microsoft.com>
If we sent a DHCP packet and get a BOOTP response from the server, we
shouldn't try to send a DHCPREQUEST packet, since it won't be DHCPACKed.
Transition straight to BIND. This is only enabled for UNIT_TEST to avoid
bloat, since I suspect the number of BOOTP servers in the wild is
vanishingly small.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
These defines are useful when testing bootp.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
When fastboot is enabled in U-Boot proper and SPL_NET is enabled, we will
try to (unsuccessfully) reference it in SPL. Fix these linker errors by
conditioning on SPL_UDP/TCP_FUNCTION_FASTBOOT.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This old patch was marked as deferred. Bring it back to life, to continue
towards the removal of common.h
Move this out of the common header and include it only where needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Make sure to stay within bounds, as a misbehaving HTTP server
can trigger a buffer overflow if not properly handled.
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
The last user of the NEEDS_MANUAL_RELOC has been removed in commit
26af162ac8 ("arch: m68k: Implement relocation")
Remove now unused NEEDS_MANUAL_RELOC code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The last user of the NEEDS_MANUAL_RELOC has been removed in commit
26af162ac8 ("arch: m68k: Implement relocation")
Remove now unused NEEDS_MANUAL_RELOC code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
In the case of NETLOOP_SUCCESS, the decimal value of the u32 variable
"net_boot_file_size" is printed using "%d", resulting in negative values
being reported for large file sizes. Fix this by using "%u" to print the
decimal value corresponding to the bytes transferred.
Fixes: 1411157d85 ("net: cosmetic: Fixup var names related to boot file")
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The argument len passed to function process_ra is the length of the IPv6
router advertisement message and needs to be between 0 and MTU because
it is assigned to remaining_option_len and used as a loop variable.
Addresses-Coverity-ID: 450971 ("TAINTED_SCALAR")
Signed-off-by: Ehsan Mohandesi <emohandesi@linux.microsoft.com>
Reviewed-by: Viacheslav Mitrofanov <v.v.mitrofanov@yadro.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
It seems better to call this a 'bootdev' since this is name used in the
documentation. The older 'Bootdevice' name is no-longer used and may cause
confusion with the 'bootdevice' environment variable.
Update throughout to use bootdev.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
CID 453851 : sprintf() shouldn't copy from/to tmp
CID 436278 : DHCP6 option_len should be checked before use
Signed-off-by: Sean Edmond <seanedmond@microsoft.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The variable 'node' was already invalid, so using it for further
lookup will not work.
Signed-off-by: Marcus Comstedt <marcus.comstedt@requtech.se>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
We use the terms 'distro' to mean extlinux but they are not really the
same. 'Distro' could refer to any method of booting a distribution,
whereas extlinux is a particular method.
Also we sometimes use syslinux, but it is better to use the same term in
all cases.
Rename distro to syslinux and also update bootstd uses of syslinux to use
extlinux instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
In IPv6, the default gateway and prefix length are determined by receiving
a router advertisement as defined in -
https://www.rfc-editor.org/rfc/rfc4861.
Add support for sending router solicitation (RS) and processing router
advertisements (RA).
If the RA has prefix info option and following conditions are met, then
gatewayip6 and net_prefix_length of ip6addr env variables are initialized.
These are later consumed by IPv6 code for non-local destination IP.
- "Router Lifetime" != 0
- Prefix is NOT link-local prefix (0xfe80::/10)
- L flag is 1
- "Valid Lifetime" != 0
Timing Parameters:
- MAX_RTR_SOLICITATION_DELAY (0-1s)
- RTR_SOLICITATION_INTERVAL (4s) (min retransmit delay)
- MAX_RTR_SOLICITATIONS (3 RS transmissions)
The functionality is enabled by CONFIG_IPV6_ROUTER_DISCOVERY and invoked
automatically from net_init_loop().
Signed-off-by: Ehsan Mohandesi <emohandesi@linux.microsoft.com>
Tested-by: Viacheslav Mitrofanov <v.v.mitrofanov@yadro.com>Reviewed-by:
Tested-by: Viacheslav Mitrofanov <v.v.mitrofanov@yadro.com>
Reviewed-by: Viacheslav Mitrofanov <v.v.mitrofanov@yadro.com>
Tested-by: Sergei Antonov <saproj@gmail.com>
Reviewed-by: Sergei Antonov <saproj@gmail.com>
Introduce reboot, boot and continue commands support to
TCP fastboot by moving existing UDP logic into the common module.
Signed-off-by: Dmitrii Merkurev <dimorinny@google.com>
Cc: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: Simon Glass <sjg@chromium.org>
Сс: Joe Hershberger <joe.hershberger@ni.com>
Сс: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Known limitations are
1. fastboot reboot doesn't work (answering OK but not rebooting)
2. flashing isn't supported (TCP transport only limitation)
The command syntax is
fastboot tcp
Signed-off-by: Dmitrii Merkurev <dimorinny@google.com>
Cc: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: Simon Glass <sjg@chromium.org>
Сс: Joe Hershberger <joe.hershberger@ni.com>
Сс: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Make following changes to unblock TCP fastboot support:
1. Implement being a TCP server support
2. Introduce dedicated TCP traffic handler (get rid of UDP signature)
3. Ensure seq_num and ack_num are respected in net_send_tcp_packet
function (make sure existing wget_cmd code is reflected with the fix)
Signed-off-by: Dmitrii Merkurev <dimorinny@google.com>
Cc: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: Simon Glass <sjg@chromium.org>
Сс: Joe Hershberger <joe.hershberger@ni.com>
Сс: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Adds DHCPv6 protocol to u-boot.
Allows for address assignement with DHCPv6 4-message exchange
(SOLICIT->ADVERTISE->REQUEST->REPLY). Includes DHCPv6 options
required by RFC 8415. Also adds DHCPv6 options required
for PXE boot.
Possible enhancements:
- Duplicate address detection on DHCPv6 assigned address
- IPv6 address assignement through SLAAC
- Sending/parsing other DHCPv6 options (NTP, DNS, etc...)
Signed-off-by: Sean Edmond <seanedmond@microsoft.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
NFSv1 support added by Christian Gmeiner, Thomas Rienoessl,
September 27, 2018. As of now, NFSv3 is the default choice.
if the server does not support NFSv3, we fall back to
versions 2 or 1.
Signed-off-by: Thomas RIENOESSL <thomas.rienoessl@bachmann.info>
The phy_init() is now used only to perform manual relocation of PHY
driver callbacks. Wrap it in ifdeffery and only call it on systems
which still require manual relocation, i.e. m68k .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Move the board_interface_eth_init() into common ethernet uclass code,
since this function could be shared by multiple drivers.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Marek Vasut <marex@denx.de>
This converts 3 usages of this option to the non-SPL form, since there is
no SPL_PHY_FIXED defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 1 usage of this option to the non-SPL form, since there is
no SPL_NETDEVICES defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 3 usages of this option to the non-SPL form, since there is
no SPL_FASTBOOT_FLASH defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
One extra character was being checked in the IPv6 string which caused the
last character of the address to be neither '\0' nor ':'. This raises an
error condition and causes the function to always return an error. This
issue was resolved by this fix.
Signed-off-by: Ehsan Mohandesi <emohandesi@microsoft.com>
Reviewed-by: Viacheslav Mitrofanov <v.v.mitrofanov@yadro.com>
It should be possible to specify a netmask when
setting a static IPv6 address. For example:
setenv ip6addr 2001:cafe:cafe:cafe::100/64
The net_prefix_length and net_ip6 should be updated
properly.
Signed-off-by: Sean Edmond <seanedmond@microsoft.com>
Reviewed-by: Viacheslav Mitrofanov <v.v.mitrofanov@yadro.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
In rfc7440, if an ACK is not received by the server or if the
last data block in a window is dropped, the server will timeout and
retransmit the window. In this case, the block count received will be
less than the internal block count. In this case, the client
should not ACK. ACK should only be sent if the received block
count is greater than the expected block count.
Signed-off-by: Sean Edmond <seanedmond@linux.microsoft.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Allow rcv() and xmit() dsa driver ops to be optional in case a driver
does not care to mangle a packet as in U-Boot only one network port is
enabled at a time and thus no packet mangling is necessary.
Suggested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Add a function to sanity check a dsa driver having proper ops.
Suggested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
In order to ensure that a DSA driver probe gets called before
dsa_ops->port_probe move the port_probe of the cpu_port to
a post-probe function.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
If a DM_MDIO driver is used we need to scan the subnodes as well.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
We need extensions to be set up before we start trying to boot any of the
bootdevs. Add a new priority before all the others for tht sort of thing.
Also add a 'none' option, so that the first one is not 0.
While we are here, comment enum bootdev_prio_t fully and expand the test
for the 'bootdev hunt' command.
Signed-off-by: Simon Glass <sjg@chromium.org>
Sometimes ethernet devices are attached to PCI. Since it is quick to scan,
add this into the ethernet hunter.
Run dhcp to establish the network connection. Drop this from the bootdev
since that is not needed now. Update a log message for clarity.
Signed-off-by: Simon Glass <sjg@chromium.org>
Most tests don't want these and can create a lot of noise. Add a way to
disable them. Use that in tests, with a flag provided to enable them for
tests that need this feature.
Signed-off-by: Simon Glass <sjg@chromium.org>
