There are a number of miscellaneous boot images at the top level of the
kconfig menu. Move these into the 'boot options' menu.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the autoboot options are in cmd/Kconfig but they don't really
relate to commands. They relate to booting, so move this menu under the
boot menu.
Signed-off-by: Simon Glass <sjg@chromium.org>
Most of the boot options are in common/Kconfig but that file is already
extremely large. Create a new Kconfig.boot to hold the boot options.
Signed-off-by: Simon Glass <sjg@chromium.org>
There are quite a few boot-related menu options at the top level. Create a
new menu to hold these and move 'Boot images' into it.
Signed-off-by: Simon Glass <sjg@chromium.org>
- Move ASPEED ram driver, update.
- Exhance pinctrl/gpio support, update Kendryte K210 support
- Enhance qemu_arm64 support for a single binary to work with and
without TF-A
Generate 'u-boot-splx4.sfp' which consist of 4 SPL images required
for booting up Cyclone5/Arria10.
By default, this 'u-boot-splx4.sfp' is generated without extra
padding after each SPL image.
For Cyclone5, 'u-boot-splx4.sfp' contains:
4 x SPL(64KB) = 256KB
For Arria10, 'u-boot-splx4.sfp' contains:
4 x SPL(256KB) = 1024KB
For Cyclone5 using NAND flash image layout for 128 KB memory blocks,
user can 'make' the following target to generate 4 SPL images with
padding:
make u-boot-spl-padx4.sfp
'u-boot-spl-padx4.sfp' contains four 128KB SPL images (each 64KB SPL is
followed by 64KB of zero-padding).
4 x (SPL(64KB) + zero-padding(64KB)) = 512KB
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
CONFIG_OF_EMBED was primarily enabled to support the S10/Agilex
spl hex file requirements. Since this option now produces a
warning during build, and the spl hex can be created using
alternate methods, CONFIG_OF_EMBED is no longer needed.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Add param entry point (ep) support for Arria 10 header. User can pass in
'e' option to mkimage to set the entry point. This is an optional option.
If not specified, default is 0x14.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Move to use generic handoff dtsi (socfpga_arria10-handoff.dtsi) and include
the specify generated _handoff.h header file from qts-filter-a10.sh script.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Add a script to process HPS handoff data and generate a header
for inclusion in u-boot specific devicetree addons. The header
should be included in the top level of u-boot.dtsi.
Signed-off-by: Dalon Westergreen <dalon.westergreen@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Don't invoke 'SYSTEM_RESET' PSCI function because PSCI
function calls are not supported by u-boot running in EL3.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Resend mailbox command for 3 times with 2ms interval in between if
it receives MBOX_RESP_TIMEOUT and MBOX_RESP_DEVICE_BUSY response code.
Add a wrapper function mbox_send_cmd_common_retry() for retry, change
all the callers to use this wrapper function.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Sync latest mailbox response codes from SDM firmware.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Mailbox command which is too large to fit into the mailbox
FIFO command buffer can be sent to SDM in multiple parts.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Mailbox driver should always check for the length of the response
and read the response data before returning the response status to
caller.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Add miliseconds delay when waiting for mailbox event to happen
before timeout. This will ensure the timeout duration is predictive.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Document down the usage of boot_scratch_cold register to avoid
overlapping of usage in the code for S10 & Agilex.
The boot_scratch_cold register is generally used for passing
critical system info between SPL, U-Boot and Linux.
Signed-off-by: Chin Liang See <chin.liang.see@intel.com>
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Enable FPGA full reconfiguration support with Intel FPGA SDM
Mailbox driver for Agilex.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Ensure watchdog reset is not triggered if the fpga
reconfiguration is taking too long.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Rename Stratix10 FPGA driver to Intel FPGA SDM Mailbox driver
because it is using generic SDM (Secure Device Manager) Mailbox
interface shared by other platform (e.g. Agilex) as well.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
All SoCFPGA platforms (except Cyclone V) are now switching
to CONFIG_WDT (driver model for watchdog timer drivers)
from CONFIG_HW_WATCHDOG.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Print reset state (warm/cold) together with the
source (watchdog/MPU) which has triggered the warm
reset on S10 & Agilex.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Include SDM triggered warm reset bit (BIT1) in Reset Manager's stat
register when checking for HPS warm reset status.
Refactor the warm reset mask macro for clarity purpose.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Rename the driver from S10 to SoC64 because Intel Agilex platform
also using the this SYSRESET SoCFPGA driver for S10.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
In current implementation, any exception would trigger a CPU reset.
But a bad written SPL would cause infinite loop where the system
will reload the same SPL instead of loading factory safe image.
Hence this patch is to ensure any exception will cause a hang. At this
moment, watchdog shall be triggered and Remote System Update mechanism
shall load the next production image or factory safe image.
Signed-off-by: Chin Liang See <chin.liang.see@intel.com>
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Timer only need to be initialized once in SPL.
This patch remove the redundancy of initializing the
timer again in U-Boot proper
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
'dwmac_socfpga' driver will setup the PHY interface during probe.
PHY interface setup in arch_misc_init() is no longer needed.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Add additional membus writes to configure main and peripheral PLL
for Agilex's clock manager.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Since warm reset may optionally set the CLock Manager to'boot mode',
the clock driver should always force the Agilex's Clock Manager to
'boot mode' before the clock driver start configuring the Clock Manager
in SPL.
In SSBL, clock driver will skip the Clock Manager configuration
if it's already being setup by SPL (Clock Manager NOT in 'boot
mode') to prevent any inaccurate clocking issues happened on HPS
peripherals such as UART, MAC and etc.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Some drivers probing failed if clock enable function is not supported in
clock driver. So, add clock enable function to clock driver to solve it.
Return 0 (success) for *.enable function because all clocks are enabled
by default in clock driver probe.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Now that PIE works when U-Boot is started from ROM, let's enable
CONFIG_POSITION_INDEPENDENT, which allows to load U-Boot also via
ARM Trusted-Firmware's fip.bin to DRAM, without tweaking the
configuration.
To get a writable initial stack, we need to keep the fixed initial
stack pointer, which points to DRAM in our case.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
CONFIG_ARCH_SUPPORT_TFABOOT was used on the qemu-arm64 platform to
guard a tweak to the flash bank configuration. U-Boot now reads the
current flash setup from the devicetree, so there is no need for
this option anymore.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Currently we hard-code the number and initial addresses of QEMU's flash
banks, even though our code is perfectly able to gather the same
information from the DTB provided by QEMU.
This is especially annoying, since we have two slightly different
U-Boot configurations ("bare-metal" vs. loaded via Arm Trusted
Firmware), which need to be selected at build time.
Drop the two hard coded alternatives, and use
CONFIG_SYS_MAX_FLASH_BANKS_DETECT instead, which relies on the DTB to
figure out the actual flash configuration at runtime.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Currently selecting CONFIG_POSITION_INDEPENDENT also forces us to use an
initial stack pointer relative to the beginning of the BSS section.
This makes some sense, because this should be writable memory anyway.
However the BSS section is not cleared or used until later in the
setup process (after relocation), so memory nearby might not be
available early enough to host the initial stack. This is an issue if
U-Boot is loaded from (Flash-)ROM, for instance.
Allow CONFIG_INIT_SP_RELATIVE to be turned off by a board's config, to
be able to select a fixed stack pointer, for instance in known good
DRAM.
This will help QEMU utilising PIE, when it's loaded to (Flash-)ROM.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
When the actual offset between link and runtime address is zero, there
is no need for patching up U-Boot early when running with
CONFIG_POSITION_INDEPENDENT.
Skip the whole routine when the distance is 0.
This helps when U-Boot is loaded into ROM, or in otherwise sensitive
memory locations.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
When we build an arm64 target and enable POSITION_INDEPENDENT, we were
skipping our build-time dynamic relocation fixup routine (STATIC_RELA).
This was probably done because we didn't need it in this case, as the
PIE fixup routine in start.S would take care of that at runtime.
However when we now skip this routine (upon detecting that the fixup
offset is 0), this might lead to uninitialised pointers.
Remove the exception, so that we always do the build-time relocation.
NOTE: GNU binutils starting with v2.27.1 do this build-time relocation
automatically, to be in-line with other architecures. So on newer
toolchains our manual fixup is actually not needed. It doesn't hurt to
have it, though, so that we keep compatibility with the popular Linaro
toolchains, which lack this feature.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
The CONFIG_TFABOOT option is more about what U-Boot DOES NOT need to do
than to support some features.
Explain a bit more in the Kconfig help text to avoid misunderstandings.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Most users don't need the standalone API examples. Distributions like SUSE
do not supply libgcc for cross-compiling and we cannot do without on ARMv8
for building examples/.
Make examples selectable via symbol CONFIG_EXAMPLES. It defaults to
yes on ARCH_QEMU to ensure that we compile the API as part of our
continuous integration.
Cc: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
The timeout calculation is based on the clk being in KHz but
the clk api returns the clk value in Hz. Convert this to KHz
to calculate the correct timeout value.
Signed-off-by: Jack Mitchell <ml@embed.me.uk>
Add a device tree binding for the BOOT button on the Maix board.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
This patch adds the necessary device tree bindings.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Rick Chen <rick@andestech.com>
