If the bd718x7 is required, but PMIC_CHILDREN is disabled, this
driver throws a compile error. Fix this by putting the function
to bind children into an if-statement checking for PMIC_CHILDREN.
Allowing PMIC_CHILDREN to be disabled in SPL saves some space and
still permits some read/write functions to access the PMIC in
early startup.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The e10133 workaround was broken in two places:
- The code intended to temporarily mask all interrupts in GPC_IMRx_CORE0.
While the old register values were saved, the actual masking was
missing.
- imx_udelay() expects the system counter to run at its base frequency,
but the system counter is switched to a lower frequency earlier in
psci_system_suspend(), leading to a much longer delay than intended.
Replace the call with an equivalent loop (linux-imx 5.15 does the same)
This fixes the SoC hanging forever when there was already a wakeup IRQ
pending while suspending.
Fixes: 57b620255e ("imx: mx7: add system suspend/resume support")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
This enables armv8 crypto extension usage for SHA1/SHA256.
Which speed up sha1/sha256 operations, about 10x faster with
a imx8mm evk for a 20MiB kernel hash verification (12ms vs 165ms).
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Fabio Estevam <festevam@denx.de>
The RD-AC5X-32G16HVG6HLG-A0 development board main components and
features include:
* Main 12V/54V power supply
* 270 Gbps throughput packet processor on the main board
* DDR4:
* SR1: 2GB DDR4 2400MT/S(1GB x 2 pcs ) with ECC(1GB x 1 pcs)
* SR2: 4GB DDR4 2400MT/S(2GB x 2 pcs ) with ECC(2GB x 1 pcs)
* PCB co-layout with 4GB device to support 8GB (Dual CS) requirement
* 16GB eMMC (Samsung KLMAG1JETD-B041006)
* 16MB SPI NOR(GD25Q127C)
* 32 x 1000 Base-T interfaces
* 16 x 2500 Base-T interfaces
* SR1: 88E2540*4
* SR2: 88E2580*1+88E2540*2
* Six (6) x 25G Base-R SFP28 interfaces
* One (1) x RJ-45 console connector, interfacing to the on board UART
* One (1) x USB Type-A connector, interfacing to the USB 2.0 port (0)
* One (1) x USB Type-mini B connector, interfacing to the USB 2.0 port (1)
* One (1) x RJ-45 1G Base-T Management port, interfacing to the host
port (shared with PCIe) Connected to 88E1512 Gigabit Ethernet Phy
* One (1) x Oculink port, interfacing to the PCIe port for external CPU
connection
* POE 802.3AT support on Port 1 ~ Port 32, 802.3BT support on Port 33 ~
Port 48 (Microsemi PD69208T4, PD69208M or TI TPS2388,TPS23881
solution)
* POE total power budget 780W
* LED interfaces per network port/POE
* LED interfaces (common) showing system status
* PTP TC mode Supported (Reserved M.2 connector to support BC mode)
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Add support for the Allecat5/Alleycat5X SoC. These are L3 switches with
an integrated CPU (referred to as the CnM block in Marvell's
documentation). These have dual ARMv8.2 CPUs (Cortex-A55). This support
has been ported from Marvell's SDK which is based on a much older
version of U-Boot.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Unlike the other 64-bit mvebu SoCs the AlleyCat5 uses the older ehci
block from the 32-bit SoCs. Adapt the ehci-marvell.c driver to cope with
the fact that the ac5 does not have the mbus infrastructure the 32-bit
SoCs have and ensure USB_EHCI_IS_TDI is selected.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Add support for the AlleyCat5 SoC. This lacks the mbus from the other
users of the mvneta.c driver so a new compatible string is needed to
allow for a different window configuration.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The 64-bit mvebu SoCs don't have a suitable timer driver so add a !ARM64
condition to the select.
Fixes: 7b530bb19e ("arm: mvebu: Use CONFIG_TIMER on all MVEBU & KIRKWOOD platforms")
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
File name with pattern u-boot-spl* is used on all places except in kwb
image for binary with SPL-only code. Combined binary with both SPL and
proper U-Boot in other places has file name pattern u-boot-with-spl*.
Make it consistent also for kwb image and rename u-boot-spl.kwb to
u-boot-with-spl.kwb as this image contains both SPL and proper U-Boot code.
Also update documentation about file name changes.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
The uart1 node was missing the 'clock-frequency' property. This meant
the driver for this device would fail at probe.
The clock for uart1 is fed from the same source as uart0 and is a fixed
200MHz clock. This is confirmed via documentation for the CN9130 SoC
and from the equivalent code in Linux at:
<linux>/arch/arm64/boot/dts/marvell/armada-ap80x.dtsi
where uart0 and uart1 share a common 'clocks' definition.
Signed-off-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Reviewed-by: Stefan Roese <sr@denx.de>
Documentation:
* Provide a document about security issue handling.
UEFI:
* Let networking support depend on NETDEVICES.
* Discover if no efi_system_partition is set.
Other:
* MAINTAINERS: add arch/arm/lib/*_efi.* to EFI_PAYLOAD.
-----BEGIN PGP SIGNATURE-----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=MoPl
-----END PGP SIGNATURE-----
Merge tag 'efi-2023-01-rc1-4' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2023-01-rc1-4
Documentation:
* Provide a document about security issue handling.
UEFI:
* Let networking support depend on NETDEVICES.
* Discover if no efi_system_partition is set.
Other:
* MAINTAINERS: add arch/arm/lib/*_efi.* to EFI_PAYLOAD.
AllocatePages() can be called with Type=AllocateAddress. Such a call can
only succeed if *Memory points to the address of an unallocated page range.
A call with *Memory being an address that is not page aligned must not
succeed. The UEFI specification requires returning EFI_OUT_OF_RESOURCES
if the requested pages cannot be allocated.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
'cert-to-efi-hash-list -t 0' does not work as expected, it produces
indeterminate timestamp.
$ cert-to-efi-hash-list -t 0 -s 256 db.crt dbx_hash.crl
TimeOfRevocation is 0-113-0 00:00:255
If we need the CRL revoked for all the time, just don't specify
'-t' option.
$ cert-to-efi-hash-list -s 256 db.crt dbx_hash.crl
TimeOfRevocation is 0-0-0 00:00:00
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Variable efi_system_partition holds the efi_system_partition. Currently it
is initialized as:
{
.uclass_id = 0 = UCLASS_ROOT,
.denum = 0,
.part = 0,
}
This indicates that host 0:0 is the efi_system_partition and we see output
like:
=> bootefi hello
** Bad device specification host 0 **
Couldn't find partition host 0:0
To identify that no EFI system partition has been set use UCLASS_INVALID.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Since the commit a9bf024b29 ("efi_loader: disk: a helper function to
create efi_disk objects from udevice"), CONFIG_EFI_SETUP_EARLY option is
by default on and will never be turned off.
So just remove this option.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
CONFIG_NET does not imply that there are actually network devices
available, only CONFIG_NETDEVICES does. Changing to this dependency
obsoletes the check in Kconfig because NETDEVICES means DM_ETH.
Fixes: 0efe1bcf5c ("efi_loader: Add network access support")
Suggested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Based loosely on the Linux kernel
Documentation/admin-guide/security-bugs.rst file, create a basic
security document for U-Boot. In sum, security issues should be
disclosed in public on the mailing list if at all possible as an initial
position.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The output of the sbi command has been changed since the last release of
the man-page. Update the example.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Fixes a crash during probing of sd card readers without medium present.
Seen with the device below but reported for many other devices.
idVendor 0x0bda Realtek Semiconductor Corp.
idProduct 0x0326 Card reader
bcdDevice 11.24
iManufacturer 1 Realtek
iProduct 2 USB3.0 Card Reader
iSerial 3 201404081410
Link: https://github.com/AsahiLinux/linux/issues/44
Link: https://lists.denx.de/pipermail/u-boot/2022-July/489717.html
Signed-off-by: Janne Grunau <j@jannau.net>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Logitech Unifying Receiver 046d:c52b bcdDevice 12.10 seems
sensitive about the first Get Descriptor request. If there
are any other requests in the same microframe, the device
reports bogus data, first of the descriptor parts is not
sent to the host. Wait over one microframe duration before
issuing subsequent requests to avoid probe failure with
this device, since it can be used to connect USB keyboards.
Signed-off-by: Marek Vasut <marex@denx.de>
Tested-by: Janne Grunau <j@jannau.net>
The struct is only used to overlay the MMIO region, so the behavior is
the same. This obsoletes the Kconfig option for the number of ports.
Signed-off-by: Samuel Holland <samuel@sholland.org>
This patch updates Microchip MPFS Icicle Kit support. For now,
add Microchip QSPI driver and a small 4MB reservation is
made at the end of 32-bit DDR to provide some memory for
the HSS to use.
Signed-off-by: Padmarao Begari <padmarao.begari@microchip.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Add QSPI NAND device node to the Microchip PolarFire SoC
Icicle kit device tree.
The Winbond NAND flash memory can be connected to the
Icicle Kit by using the Mikroe Flash 5 click board and
the Pi 3 Click shield.
Signed-off-by: Padmarao Begari <padmarao.begari@microchip.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Rick Chen <rick@andestech.com>
In the v2022.10 Icicle reference design, the seg registers have been
changed, resulting in a required change to the memory map.
A small 4MB reservation is made at the end of 32-bit DDR to provide some
memory for the HSS to use, so that it can cache its payload between
reboots of a specific context.
Co-developed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Padmarao Begari <padmarao.begari@microchip.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Rick Chen <rick@andestech.com>
As PLICSW is used to trigger the software interrupt, we should rename
Andes PLIC configuration and file name to reflect the usage. This patch
also updates PLMT and PLICSW compatible strings to be consistent with
OpenSBI fdt driver.
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Rick Chen <rick@andestech.com>
It was noticed that while converting CONFIG_SPL_PAD_TO to Kconfig its
value for the MIPS MT762x/8x targets got not ported correctly. Its
default is not 0x10000 instead of 0x0. This patch fixes this issue.
Fixes: ca8a329a1b ("Convert CONFIG_SPL_PAD_TO et al to Kconfig")
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Ruben Winters <Ruben.Winters@gooiland-elektro.nl>
Cc: Weijie Gao <weijie.gao@mediatek.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_MIPS_TIMER_REQ
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
CPU_CLOCK_RATE is just used once for CONFIG_SYS_MIPS_TIMER_FREQ
which is migrated to Kconfig in the next patch.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Resolve all uses of CONFIG_SYS_MHZ with the currently defined value.
Remove code which depends on CONFIG_SYS_MHZ but where no board configs
actually use that code.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
This saves ~50K in the resulting u-boot.bin file which is important to
fit in the U-Boot partition defined in the flash layout of upstream Linux.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Add the needed bus mappings for the two main RTI memory ranges and
the required device tree nodes in the main domain.
Same as kernel commit 6dd8457dc20693e2ba9054c171499b22664fd4e7
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
On 64-bit platforms where int is 32-bit wide, the eeprom command
parse_numeric_param() routine truncates the memory address parameter to
the lower 32-bit. Make parse_numeric_param() return long to allow
read/write of addresses beyond the lower 4GB.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
So far the Calxeda machines were using the CONFIG_SYS_TIMER_* macros to
simply hardcode the address of the counter register of the SP804 timer.
This method is deprecated and scheduled for removal.
Use the newly introduced SP804 DM_TIMER driver to provide timer
functionality on Highbank and Midway machines. The base address and base
frequency are taken from the devicetree.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
