The dm_gpio_set_dir_flags function cannot be used to update the
configuration of a GPIO pin because it does a bitwise OR with the
existing flags. Looks like commit 788ea83412 ("gpio: add function
_dm_gpio_set_dir_flags") has introduced this behaviour and the i2c-gpio
driver has been broken since.
Signed-off-by: Harm Berntsen <harm.berntsen@nedap.com>
CC: Heiko Schocher <hs@denx.de>
CC: Patrick Delaunay <patrick.delaunay@st.com>
Because the first PCIExAR(n) register is configured with the mapping,
It is the second PCIExAR(n) register that must be written with 0, not
the last one. Update the n from 4 to 1 to select the correct register.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Both the map address and mask must be power of two per documentation,
adjust the code accordingly.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add code to access the PCIe root bus space and configure it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The mb862xx driver does not conform to the driver model and is unused.
Eliminate it.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add "boe,nv101wxmn51" to the compatible node. This is the panel for
chromebook_bob.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add "sharp,lq123p1jx31" to the compatible node. This is the panel for
chromebook_kevin.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
mmc_spi_sendcmd(), mmc_spi_readdata() and mmc_spi_writedata() are
currently undocumented. Add comment blocks to explain the arguments
and the return value.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
After command is sent and before card response shows up on the line,
there is a variable number of clock cycles in between called Ncr.
The spec [1] says the minimum is 1 byte and the maximum is 8 bytes.
Current logic in mmc_spi_sendcmd() has a flaw that it could only work
with certain SD cards with their Ncr being just 1 byte.
When resp_match is false, the codes try to receive only 1 byte from
the SD card. On the other hand when resp_match is true, the logic
happens to be no problem as it loops until timeout to receive as many
bytes as possible to see a match of the expected resp_match_value.
However not every call to mmc_spi_sendcmd() is made with resp_match
being true hence this exposes a potential issue with SD cards that
have a larger Ncr value.
Given no issue was reported as of today, we can reasonably conclude
that all cards being used on the supported boards happen to have a 1
byte Ncr timing requirement. But a broken case can be triggered by
utilizing QEMU to emulate a larger value of Ncr (by default 1 byte
Ncr is used on QEMU). This commit fixes such potential spec violation
to improve the card compatibility.
[1] "Physical Layer Specification Version 8.00"
chapter 7.5.1: Command / Response
chapter 7.5.4: Timing Values
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The argument check should happen before any transfer on the SPI lines.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
After issuing the switch command: Wait until 'current state' of the card
status becomes 'tran'. This prevents from response timeout at the next
command because of 'current state' = 'data'.
Signed-off-by: Stefan Bosch <stefan_b@posteo.net>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
If DMA(SDMA or ADMA) is not used, the cache invalidation
after reading is no need, should be skipped. Otherwise
U-Boot may hang at the cache invalidation.
Found this issue and tested this fix on DragonBoard 410c.
Fixes: commit 4155ad9aac ("mmc: sdhci: fix missing cache invalidation after reading by DMA")
Signed-off-by: Yuezhang.Mo <Yuezhang.Mo@sony.com>
Reviewed-by: Andy Wu <Andy.Wu@sony.com>
The 'brcm,bcm2711-hdmi0' compatible string is used on RPi4 instead of
'brcm,bcm2835-hdmi' since the IP core was upgraded (now called VC6
instead of VC4). This has no functional change as far as u-boot driver
is concerned. So simply add the compatible string.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
This will allow us to use DM variants of phys_to_bus()/bus_to_phys()
when relevant.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
So far we've been content with passing physical addresses when
configuring memory addresses into XHCI controllers, but not all
platforms have buses with transparent mappings. Specifically the
Raspberry Pi 4 might introduce an offset to memory accesses incoming
from its PCIe port.
Introduce xhci_virt_to_bus() and xhci_bus_to_virt() to cater with these
limitations, and make sure we don't break non DM users.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
[mb: fix compilation for 32 bit]
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
fix from nicolas
Calculating the DMA offset between a bus address space and CPU's every
time we call phys_to_bus() and bus_to_phys() isn't ideal performance
wise, as it implies traversing the device tree from the device's node up
to the root. Since this information is static and available before the
device's initialization, parse it before the probe call an provide the
DMA offset in 'struct udevice' for the address translation code to use
it.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Add the following functions to get a specific device's DMA ranges:
- dev_get_dma_range()
- ofnode_get_dma_range()
- of_get_dma_range()
- fdt_get_dma_range()
They are specially useful in oder to be able validate a physical address
space range into a bus's and to convert addresses from and to address
spaces.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
So far we've assumed a fixed configuration for inbound windows as we had
a single user for this controller. But the controller's DMA constraints
were improved starting with BCM2711's B1 revision of the SoC, notably
available in CM4 and Pi400. They allow for wider inbound windows. We can
now cover the whole address space, whereas before we where limited to
the lower 3GB.
This information is passed to us through DT's 'dma-ranges' property and
it's specially important for us to honor it since some interactions with
the board's co-processor assume we're doing so (specifically the XHCI
firmware load operation, which is handled by the co-processor after
u-boot has correctly configured the PCIe controller).
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Make sure we handover the PCIe controller in a clean state. Some of the
devices hanging from the PCIe bus might need to be properly reset
through #PERST in order for Linux to be able to initialize them.
This is specially important in order to properly initialize Raspberry Pi
4 B and 400's USB chip.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
The PCIe bus the controller is connected to might need to be removed
prior the handover. Make sure xhci-pci is also removed so as to avoid
unexpected timeouts or hangs.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
We find the iProc RNG200 in the Raspberry Pi 4. Add it to all it's
config so that it can be used.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
[mb: drop rpi_4_32b_defconfig]
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Add support for getting the 'vref-supply' regulator and register it as
ADC's reference voltage regulator, so clients can translate sampled ADC
values to the voltage.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add a simple Analog to Digital Converter device based button driver. This
driver binds to the 'adc-keys' device tree node.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add support for random number generator RNG200.
This is for example found on RPi4.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
[mb: adapt to new struct driver memebers]
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
This driver is used for the Ethernet switch integrated into LS1028A NXP.
Felix on LS1028A has 4 front panel ports and two internal ports, I/O
to/from the switch is done through an ENETC Ethernet interface.
The 4 front panel ports are available as Ethernet interfaces and can be
used with the typical network commands like tftp.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
DSA stands for Distributed Switch Architecture and it covers switches that
are connected to the CPU through an Ethernet link and generally use frame
tags to pass information about the source/destination ports to/from CPU.
Front panel ports are presented as regular ethernet devices in U-Boot and
they are expected to support the typical networking commands.
DSA switches may be cascaded, DSA class code does not currently support
this.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
The DSA (Distributed Switch Architecture) implementation has made a
design decision when it got introduced to the Linux kernel in 2008.
That was to hide away from the user the CPU-facing Ethernet MAC, since
it does not make sense to register it as a struct net_device (UCLASS_ETH
udevice for U-Boot), because that would never be beneficial for a user:
they would not be able to use it for traffic, since conceptually, a
packet delivered to the CPU port should loop back into the system.
Nonetheless, DSA has had numerous growing pains due to the lack of a
struct net_device for the CPU port, but so far it has overcome them.
It is unlikely at this stage of maturity that this aspect of it will
change.
We would like U-Boot to present the same information as Linux, to be at
parity in terms of number of interfaces, so that ethNaddr environment
variables could directly be associated between U-Boot and Linux.
Therefore, we would implicitly like U-Boot to hide the CPU port from the
user as well.
But the paradox is that DSA still needs a struct phy_device to inform
the driver of the parameters of the link that it should configure the
CPU port to. The problem is that the phy_device is typically returned
via a call to phy_connect, which needs an udevice to attach the PHY to,
and to search its ofnode for the 'fixed-link' property. But we don't
have an udevice to present for the CPU port.
Since 99% of DSA setups are MAC-to-MAC connections between the switch
and the host Ethernet controller, the struct phy_device is going to be a
fixed PHY. This simplifies things quite a bit. In U-Boot, a fixed PHY
does not need an MDIO bus, and does not need an attached dev either.
Basically, the phy_connect call doesn't do any connection, it just
creates the fixed PHY.
The proposal of this patch is to introduce a new fixed_phy_create
function which will take a single argument: the ofnode that holds this:
port@4 {
reg = <4>;
phy-mode = "internal";
fixed-link {
speed = <2500>;
full-duplex;
};
};
and probe a fixed PHY driver using the information from this ofnode.
DSA will probably be the only user of this function.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Unlike the Linux fixed PHY driver, the one in U-Boot does not attempt to
emulate the clause 22 register set of a gigabit copper PHY driver
through the swphy framework. Therefore, the limitation of being unable
to support speeds higher than gigabit in fixed-link does not apply to
the U-Boot fixed PHY driver. This makes the fixed-link U-Boot
implementation more similar to the one from phylink, which can work with
any valid link speed.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
This adds support for RPC test trusted application emulation, which
permits to test reverse RPC calls to TEE supplicant. Currently it covers
requests to the I2C bus from TEE.
Signed-off-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org>
Acked-by: Etienne Carriere <etienne.carriere@linaro.org>
This commit gives the secure world access to the I2C bus so it can
communicate with I2C slaves (typically those would be secure elements
like the NXP SE050).
A similar service implementation has been merged in linux:
c05210ab ("drivers: optee: allow op-tee to access devices on the i2c
bus")
Signed-off-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Etienne Carriere <etienne.carriere@linaro.org>
At present this function does not accept a size for the FIT. This means
that it must be read from the FIT itself, introducing potential security
risk. Update the function to include a size parameter, which can be
invalid, in which case fit_check_format() calculates it.
For now no callers pass the size, but this can be updated later.
Also adjust the return value to an error code so that all the different
types of problems can be distinguished by the user.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Bruce Monroe <bruce.monroe@intel.com>
Reported-by: Arie Haenel <arie.haenel@intel.com>
Reported-by: Julien Lenoir <julien.lenoir@intel.com>
This board has not been converted to CONFIG_DM by the deadline of v2020.01
and is missing other conversions which depend on this as well. Remove it.
As this is the last SH4A board, remove that support as well.
Cc: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM by the deadline of v2020.01
and is missing other conversions which depend on this as well. Remove it.
Patch-cc: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Patch-cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline of
v2019.04, which is almost two years ago. In addition there are other DM
migrations it is also missing. Remove it.
Cc: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This board has not been converted to CONFIG_DM_MMC by the deadline of
v2019.04, which is almost two years ago. In addition there are other DM
migrations it is also missing. Remove it.
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefano Babic <sbabic@denx.de>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmAmOowcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyGEpB/oD2ZQdqY/kfu0SlKE6
2Qor+MSwDA8yQlAKfiX2J3x0sAaGNkeUPQrWLxutACd34MJsjG41sr6uvLwu4E9f
bc91Gk1Xv/kmySi7JPfpctb01Bd1GVpzuHELIumGgYRkNSwAFFaXrqVPxr/9cN3t
dEcfbKX0p4qXUv/TDw3tE1D63dYPIJC3yX0/4n/n824AKeqRyTMVC34rjfEOoE/r
0w6YSxwQ8hlh23xwc2tyEMSKR4jNp8mAtQcl03Gi/6xiaqgH6lQ6ardSblr3qvjW
6Ev1nd3f9d8i0CzipbLH6PL4G31Ft+ZG/Z/z8wqA6w15h29wu7CfV8yC0aBV0g0/
N1ko
=7ddr
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-fixes-2021.04-a' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
First set of u-boot-atmel fixes for 2021.04 cycle:
This small PR includes just two fixes but very important: one revert in
the clk subsystem which fixes the boot on many old boards
(sama5d2_xplained, sama5d4_xplained), which currently crash at boot; and
one small fix related to debug serial on sama7g5ek board.
If probe fails, the mdio bus isn't unregistered. Fix it.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Revert changes in at91 compat.c that cause u-boot to fail booting on
sama5d4_xplained and sama5d2_xplained
Log below:
<debug_uart>
No serial driver found
Could not initialize timer (err -19)
Could not initialize timer (err -19)
Could not initialize timer (err -19)
Could not initialize timer (err -19)
Could not initialize timer (err -19)
Could not initialize timer (err -19)
Could not initialize timer (err -19)
Could not initialize timer (err -19)
Fixes: a2703ce10c ("dm: Remove uses of device_bind_offset()")
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The Linux kernel v5.7-rc1 introduced the compatible "st,stm32mp15-hsotg".
See Linux kernel commit d49850110434 ("dt-bindings: usb: dwc2: add
support for STM32MP15 SoCs USB OTG HS and FS")
This patch updates the supported compatible in DWC2 driver,
removes the add-on done in U-Boot dtsi and keeps the compatible
defined in SOC dtsi arch/arm/dts/stm32mp151.dtsi:
usbotg_hs: usb-otg@49000000 {
compatible = "st,stm32mp15-hsotg", "snps,dwc2";
reg = <0x49000000 0x10000>;
...
};
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Testing with v2021.01 on MIPS Octeon has shown, that the latest patch
for the "short packet event trb handling" did introduce a bug on
platforms with virtual address != physical address. This patch fixes
this issue by using the correct address types in the compare (both
physical in this case).
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Ran Wang <ran.wang_1@nxp.com>
Cc: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Function dm_pci_map_bar() may fail and returns NULL. Check this to prevent
dereferencing a NULL pointer.
In xhci-pci this may happen when board does not enable CONFIG_PCI_PNP and
PCI_BASE_ADDRESS_0 contains unconfigured zero address.
Signed-off-by: Pali Rohár <pali@kernel.org>
Add support to disable specific ports, it's useful for some
scenarios:
1. usb3 PHY is shared whith PCIe or SATA, the corresponding
usb3 port can be disabled;
2. some usb2 or usb3 ports are not used on special platforms,
they should be disabled to save power.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
The Amlogic AXG MIPI + PCIe Analog PHY provides function for both PCIe and
MIPI DSI at the same time, and provides the Analog part of MIPI DSI transmission
and Analog part of the PCIe lines.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The Amlogic AXG SoCs embeds a MIPI D-PHY used to communicate with DSI
panels.
This D-PHY depends on a separate analog PHY.
Signed-off-by:Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add the PHY configure op callback to the generic PHY uclass to permit
configuring the PHY.
It's useful for MIPI DSI PHYs to setup the link timings.
Signed-off-by:Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The MIPI D-PHY spec defines default values and boundaries for most of the
parameters it defines. Introduce helpers to help drivers get meaningful
values based on their current parameters, and validate the boundaries of
these parameters if needed.
These helpers and header are taken from Linux commit 9123e3a74ec7 ("Linux 5.9-rc1").
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add support of missing I2C6_K with bit 3 of RCC_MC_APB5ENSETR =
I2C6EN: I2C6 peripheral clocks enable.
This patch allows customer to use I2C6 in SPL or in U-Boot
as other I2C instance, already support in clk driver.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Bind only the enabled GPIO subnode, to avoid to probe the node
"gpio-controller" present in SOC dtsi (disabled by default) but
not enabled in the included pincontrol dtsi file.
For example, in stm32mp15xxac-pinctrl.dtsi 2 gpio bank are absent:
gpioj: gpio@5000b000
gpiok: gpio@5000c000
Then these GPIO are absent in output of command "dm tree" and
"gpio status -a"
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
OTYPE can be used for output or for alternate function to select
PP = push-pull or OP = open-drain mode, according reference manual
(Table 81. Port bit configuration table).
This patch removes this indication for input pins and adds it
for AF and output pins for pinmux command output.
Fixes: b305dbc08b ("pinctrl: stm32: display bias information for all pins")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Instead of redefining a pin's name size, use PINNAME_SIZE defined
in include/dm/pinctrl.h
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
pin-controller pin's name must be equal to pin's name used in device
tree with "pins" DT property.
Issue detected on stm32mp157c-ev1 board with goodix touchscreen.
In DT, the goodix's pin is declared in DT with the node:
goodix_pins: goodix {
pins = "gpio14";
bias-pull-down;
};
Whereas in stmfx pin-controller driver, pin's name are equal to
"stmfx_gpioxx" where xx is the pin number.
This lead to not configure stmfx's pins at probe because pins is
identified by its name (see pinctrl_pin_name_to_selector() in
pinctrl-generic.c) and stmfx pin "gpio14" can't be found.
To fix this issue, come back to the original stmfx pin's name.
Revert "pinctrl: stmfx: update pin name"
This reverts commit 38d30cdcd65c73eeefac5efa328ad444a53b77dd.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Tested-by: Patrick DELAUNAY <patrick.delaunay@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
- Espressobin: Set default env values at runtime (Pali)
- Espressobin: Set the maximum slave SPI speed to 40MHz (Pali)
- theadorable: PCIe test code enhancement and early deemphasis
enabling (Stefan)
- pci_mvebu: Disable config access to PCI host bridge ports (Stefan)
- mv_sdhci: parse device-tree entry (Baruch)
Update gpio driver to use same logic for big-endian and little-endian
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
LX2162A is not like LX2160A which has different PCIe controller
in rev1 and rev2 silicon. It supports only one configuration of
PCIe controller, which is same as LS2088A. So update PCIe
compatible string same as LS2088A.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Wasim Khan <wasim.khan@nxp.com>
Tested-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This patch moves the SVR definitions to a new svr.h for
Layerscape armv7 and armv8 platforms respectively, so that
the PCIe driver can reuse them.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The LS1088 requires the same QUADSPI_QURIK_BASE_INTERNAL
workaround as the LS208x and also has a 64 byte TX buffer.
With the previous settings SPI-NAND reads over AHB were
corrupted.
Fixes: 91afd36f38 ("spi: Transform the FSL QuadSPI driver to use the SPI MEM API")
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Adapted from kernel commit b0177aca7aea
From: Michael Walle <michael@walle.cc>
Make use of a core helper to ensure the desired width is respected
when calling spi-mem operators.
Otherwise only the SPI controller will be matched with the flash chip,
which might lead to wrong widths. Also consider the width specified by
the user in the device tree.
Fixes: 91afd36f38 ("spi: Add a driver for the Freescale/NXP QuadSPI controller")
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20200114154613.8195-1-michael@walle.cc
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Mathew McBride <matt@traverse.com.au> [adapt for U-Boot]
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Current MDIO wait time is too long, which introduce long delay when
PHY negotiation register checking. Reduce it to 10us
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Fugang Duan <Fugang.duan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
We have encountered circumstances when a board design does not include
pull-up resistors on the external MDIO buses which are not used. This
leads to the MDIO data line not being pulled-up, thus the MDIO controller
will always see the line as busy.
Without a timeout in the MDIO bus driver, the execution is stuck in an
infinite loop when any access is initiated on that external bus.
Add a timeout in the driver so that we are protected in this
circumstance. This is similar to what is being done in the Linux
xgmac_mdio driver.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Provide an explicit configuration option to disable default "unlock all"
of any flash chip which supports locking. It doesn't make sense to
automatically unprotect the entire flash on each u-boot startup if the
block protection bits are actually used.
Traditionally, the unlock was there to be able to write to flash devices
which powered-up with the block protection bits set. Over time this
feature creeped into all flash devices which support locking.
For a more detailed description and discussion see:
https://lore.kernel.org/linux-mtd/20201203162959.29589-8-michael@walle.cc/
Keep things simple in u-boot and just provide a configration option to
disable this behavior which can be set per board.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Call mmc_of_parse() so that generic DT properties like 'non-removable'
are taken into account.
This fixes boot on Clearfog with eMMC on SOM that requires the
non-removable property.
Reported-by: Thorsten Spille <thorsten_spille@netcor.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
This patch changes the PCI config routines in the Armada XP / 38x driver
to not allow access to the PCIe root ports.
While updating the Armada XP based theadorable to the latest mainline
and testing it with the DM PCI driver I noticed, that the PCI root
bridge was being configured incorrectly. Resulting in the PCIe Intel
WiFi was not working correctly in Linux. With this patch applied, all
PCIe devices work without any issues in Linux again.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Marek Behún <marek.behun@nic.cz>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Mario Six <mario.six@gdsys.cc>
In case MMC has MBR system and fastboot writes GPT,
MMC is still recognized as MBR.
Invoke part_init() to purge cached data and update
information about partition table type.
Signed-off-by: Roman Stratiienko <r.stratiienko@gmail.com>
Add command oem bootbus which executes the command
``mmc bootbus <id> <arg>`` on the current fastboot mmc device
(<i> = CONFIG_FASTBOOT_FLASH_MMC_DEV) to set the eMMC boot
configuration on first update, with
<arg> = boot_bus_width reset_boot_bus_width boot_mode
$> fastboot oem bootbus:<boot_bus_width> <reset_boot_bus_width> <boot_mode>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add fastboot command oem partconf which executes the command
``mmc partconf <id> <arg> 0`` on the current <id> mmc device
to configure the eMMC boot partition with
<arg>: boot_ack boot_partition, so the command is:
$> fastboot oem partconf:<boot_ack> <boot_partition>
The partition_access argument is forced to 0 (userdata)
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
[lukma - Kconfig adjustments after merging this patch]
Update the code and the configs for eMMC boot and userdata
partitions acces
- FASTBOOT_MMC_BOOT_SUPPORT: boot partition 1 and 2 (erase/write)
- FASTBOOT_MMC_BOOT1_NAME: boot partition 1, default name="mmc0boot0"
- FASTBOOT_MMC_BOOT2_NAME: boot partition 2, default name="mmc0boot1"
This patch also removes the unnecessary dependency with
ARCH_MEDIATEK and EFI_PARTITION.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Split userdata and boot partition support for eMMC update
and correct the description (update is supported).
The new configuration CONFIG_FASTBOOT_MMC_USER_SUPPORT
allows to activate support of userdata partition update,
based on target name=CONFIG_FASTBOOT_MMC_USER_NAME
This patch also removes the unnecessary dependency with
ARCH_MEDIATEK and EFI_PARTITION.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
It is possible to implement fastboot_set_reboot_flag in a generic way
if BCB commands are turned on for a target. Using
bcb_set_reboot_reason allows to do this by simply passing string with
correct reboot reason that should be handled during next boot process.
If BCB are turned off, then bcb_set_reboot_reason would simply return
error, so it won't introduce any new behaviour for such targets.
Signed-off-by: Roman Kovalivskyi <roman.kovalivskyi@globallogic.com>
This reverts commit 0ebf9842e5.
Current generic implementation of fastboot_set_reboot_flag is somewhat
messy and requires some additional configuration option to be enabled
besides CMD_BCB, so it reverts that implementtion in order to bring a
new cleaner one.
Next commit introduces new generic implementation of
fastboot_set_reboot_flag.
Signed-off-by: Roman Kovalivskyi <roman.kovalivskyi@globallogic.com>
- Sync DTS from Linux kernel for all K3 platforms
- Add MMC higher speed nodes for AM65x, J721e, J7200
- Convert Nokia RX-51 to use CONFIG_DM_MMC
- Minor fixes for LEGO MINDSTORMS
Use the generic sdhci_set_control_reg() instead of duplicating
in platform driver.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
According to the AM654x Data Manual[1], the setup timing in lower speed
modes can only be met if the controller uses a falling edge data launch.
To ensure this, the HIGH_SPEED_ENA (HOST_CONTROL[2]) bit should be
cleared in default speed, SD high speed, MMC high speed, SDR12 and SDR25
speed modes.
Use the sdhci writeb callback to implement this condition.
[1] http://www.ti.com/lit/gpn/am6546 Section 5.10.5.16.1
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
With the new SW tuning App note[1], a custom tuning algorithm is
required for eMMC HS200, HS400 and SD card UHS modes. The algorithm
involves running through the 32 possible input tap delay values and
sending the appropriate tuning command (CMD19/21) for each of them
to get a fail or pass result for each of the values. Typically, the
range will have a small contiguous failing window. Considering the
tuning range as a circular buffer, the algorithm then sets a final
tuned value directly opposite to the failing window.
[1] https://www.ti.com/lit/pdf/spract9
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Add support for writing new clock buffer select property for both
the am654x and j721e 4 bit IPs
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
DLL need only be enabled for speed modes and clock frequencies at or
above 50 MHz. For speed modes that don't enable the DLL, we need to
configure a static input delay value. This involves reading an optional
itap-del-sel-* value from the device tree and configuring it for the
appropriate speed mode.
Therefore, move all dll configurations to their own functions and gate it
with 50 MHz speed and a minimum mode. If both these conditions are not
satisfied then configure delay chain modes.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Add Support for AM65x PG2.0. Use the SoC bus framework to fixup
the platform data and do DLL calibration if the revision is 1.0
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Not all controllers need calibration for the PHY DLL. Add a DLL_CALIB
flag to indicate the same.
Also move the write of trm_icp and driver strength to the set_clock()
function to match the kernel configuration flow.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Convert the flags field defines to use the BIT() macro.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
There are some speed modes that work without switching the dll on.
Unconditionally switch off the DLL before setting clock frequency to
support this case. The software will automatically enable DLL for speed
modes that require it. This also means the dll_on priv data member is no
longer required.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Add a set_voltage() function which handles the switch from 3.3V to 1.8V
for SD card UHS modes.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The K3 R5F remoteproc driver in U-Boot was upstreamed prior to the
equivalent remoteproc driver in the Linux kernel. Some of the DT
properties used in U-Boot got upstreamed using different names
in Linux kernel.
The modified property names include the R5F cluster mode configuration
property "lockstep-mode"; and three different individual R5F core config
properties - "atcm-enable", "btcm-enable" and "loczrama". The property
names were updated as follows:
lockstep-mode => ti,cluster-mode
atcm-enable => ti,atcm-enable
btcm-enable => ti,btcm-enable
loczrama => ti,loczrama
Update the K3 R5F remoteproc driver, the corresponding binding, and
all the existing usage in AM65x, J721E and J7200 dts files all at
once to use the new properties and to not break any bisectability.
Signed-off-by: Suman Anna <s-anna@ti.com>
The dm_spi_ops.xfer() API does not support dual and quad SPI modes. It
also doesn't allow the zynqmp_gqspi driver to calculate the correct
number of dummy cycles for some NOR ops (as doing so also requires the
buswidth).
Port the zynqmp_gqspi driver to spi_controller_mem_ops, which gives us
the buswidth values to correctly support all SNOR_PROTO_X_X_X commands
and to properly calculate dummy cycles.
Signed-off-by: Brandon Maier <brandon.maier@rockwellcollins.com>
CC: jagan@amarulasolutions.com
CC: michal.simek@xilinx.com
CC: Ashok Reddy Soma <ashokred@xilinx.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
sandbox_scmi_devices_ctx() may return NULL. We should not dereference this
value in sandbox_scmi_devices_remove().
The problem was indicated by 'gcc-11 -fanalyzer'.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
priv->iobase was declared as phys_addr_t which is now a 64-bit
address. In a 32-bit build, this causes the following warning
seen when building ftmac100.c:
warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
Cast priv->iobase with uintptr_t.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
dev_read_addr() returns fdt_addr_t which is now a 64-bit address.
In a 32-bit build, this causes the following warning seen when
building serial_sifive.c:
warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
Cast the return value with uintptr_t.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Add another flag to the DM core which could be assigned to drivers and
which makes those drivers call their remove callbacks last, just before
booting OS and after all the other drivers finished with their remove
callbacks. This is necessary for things like clock drivers, where the
other drivers might depend on the clock driver in their remove callbacks.
Prime example is the mmc subsystem, which can reconfigure a card from HS
mode to slower modes in the remove callback and for that it needs to
reconfigure the controller clock.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
At present if device_remove() decides that the device should not actually
be removed, it still calls the uclass pre_remove() method and powers the
device down.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the uclass pre-remove method is called before the children are
removed. But the children may refused to be removed, in whch case the
uclass is in a tricky situation. At present we handle this by calling
the uclass' post_probe() method. But it seems better to avoid doing
anything with the uclass in this case.
Switch the ordering so that we make sure the children can be removed
before advising the uclass.
Signed-off-by: Simon Glass <sjg@chromium.org>
This flag has the word 'REMOVE' in it which means it conflicts with
the DM_REMOVE flags. Rename it to DM_FLAG_LEAVE_PD_ON which seems to
indicate its purpose well enough.
Signed-off-by: Simon Glass <sjg@chromium.org>
This has no useful meaning in U-Boot and will never be returned. We want
to reserve this flag for internal driver model use.
Drop the code.
Signed-off-by: Simon Glass <sjg@chromium.org>
This has no useful meaning in U-Boot. Use -ENOMEM since that appears to
be what has gone wrong in this case. We want to reserve this flag for
internal driver model use.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
- Fix CMD_ACPI dependency in Kconfig
- Correct overflow in __udelay() in TSC timer driver
- Add a devicetree node for eMMC for Coral
- Minor improvements on image loading
- Reduce size of Samus image
At present long delays such as msleep(2000) can cause an overflow in this
function. There is no need for this, since it already uses a 64-bit int.
Add a cast to correct this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
It is useless and misleading to print the ret variable that is not set
by the dev_read_addr routine. Also, move the '\n' character after the
round bracket that contains the error code.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The pinmux choice for the RMII/RGMII pins the EMAC is connected to is
not dependent on the EMAC IP, but on the SoC it is integrated in.
Deriving the pinmux from the DT compatible string (as we do at the
moment) will thus cause problems with certain EMAC IP / SoC combinations.
To avoid this exact issue with the H616, let's use our Kconfig MACH
symbols to choose the correct pinmux setup.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
At the moment we only consider the EPHY register for those SoCs were
we actually have an internal PHY to configure. However even other SoCs
have this register, an expect the EPHY select bit to be cleared for
proper operation with an external PHY.
Rework sun8i_emac_set_syscon_ephy() to be called regardless of the EMAC
model, and clear the H3_EPHY_SELECT bit if no internal PHY is used.
We get away without it so far because SoCs like the A64 clear this bit
on reset, but we need to explicitly clear it on the H616, for instance.
The Linux driver does so as well.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
As we need standard usb_ep's desc, so set it when enable ep.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Change to use wMaxPacketSize of current speed EP desc for request
length wrap up.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Remove the gadget driver speed check, and set its max_speed to
be USB_SPEED_HIGH.
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Tested-by: faqiang.zhu <faqiang.zhu@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
If one of functions is not super speed capable, we need force the udc
to be high speed, this is an equivalent implementation of
usb_gadget_udc_set_speed() in kernel but simple, which set the gadget
max_speed to be high speed, so afterwards when start gadget duc can
set the HW to be USB 2.0 mode.
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Tested-by: faqiang.zhu <faqiang.zhu@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Set its max_speed to be super speed.
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Tested-by: faqiang.zhu <faqiang.zhu@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add super speed EP config.
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Tested-by: faqiang.zhu <faqiang.zhu@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This patch is to add usb gadget super speed support in common
driver, including BOS descriptor and select the super speed
descriptor from function driver.
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Tested-by: faqiang.zhu <faqiang.zhu@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Always use the new added config for os_desc_config to fix cdev->
os_desc_config may miss set in case we restart usb gadget driver.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The current way to set cdev->os_desc_config is wrong if user restart
fastboot, as the old config is not used anymore and new allocated
usb_configuration will be used, so set the os_desc_config while
usb_add_config.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add device interface GUID for Microsoft Extended Properties Feature
Descriptor.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This is a proting patch from linux kernel: 37a3a533429e
("usb: gadget: OS Feature Descriptors support"), the original commit
log see below:
There is a custom (non-USB IF) extension to the USB standard:
http://msdn.microsoft.com/library/windows/hardware/gg463182
They grant permission to use the specification - there is
"Microsoft OS Descriptor Specification License Agreement"
under the link mentioned above, and its Section 2 "Grant
of License", letter (b) reads:
"Patent license. Microsoft hereby grants to You a nonexclusive,
royalty-free, nontransferable, worldwide license under Microsoft鈥檚
patents embodied solely within the Specification and that are owned
or licensable by Microsoft to make, use, import, offer to sell,
sell and distribute directly or indirectly to Your Licensees Your
Implementation. You may sublicense this patent license to Your
Licensees under the same terms and conditions."
The said extension is maintained by Microsoft for Microsoft.
Yet it is fairly common for various devices to use it, and a
popular proprietary operating system expects devices to provide
"OS descriptors", so Linux-based USB gadgets whishing to be able
to talk to a variety of operating systems should be able to provide
the "OS descriptors".
This patch adds optional support for gadgets whishing to expose
the so called "OS Feature Descriptors", that is "Extended Compatibility ID"
and "Extended Properties".
Hosts which do request "OS descriptors" from gadgets do so during
the enumeration phase and before the configuration is set with
SET_CONFIGURATION. What is more, those hosts never ask for configurations
at indices other than 0. Therefore, gadgets whishing to provide
"OS descriptors" must designate one configuration to be used with
this kind of hosts - this is what os_desc_config is added for in
struct usb_composite_dev. There is an additional advantage to it:
if a gadget provides "OS descriptors" and designates one configuration
to be used with such non-USB-compliant hosts it can invoke
"usb_add_config" in any order because the designated configuration
will be reported to be at index 0 anyway.
This patch also adds handling vendor-specific requests addressed
at device or interface and related to handling "OS descriptors"."
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
As other users may use utf8_to_utf16le() to convert the utf8
to utf16 for usb, so move it to head file.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This is a porting patch from linux kernel: 19824d5eeece
("usb: gadget: OS String support"), original commit log
see below:
"There is a custom (non-USB IF) extension to the USB standard:
http://msdn.microsoft.com/library/windows/hardware/gg463182
They grant permission to use the specification - there is
"Microsoft OS Descriptor Specification License Agreement"
under the link mentioned above, and its Section 2 "Grant
of License", letter (b) reads:
"Patent license. Microsoft hereby grants to You a nonexclusive,
royalty-free, nontransferable, worldwide license under Microsoft鈥檚
patents embodied solely within the Specification and that are owned
or licensable by Microsoft to make, use, import, offer to sell,
sell and distribute directly or indirectly to Your Licensees Your
Implementation. You may sublicense this patent license to Your
Licensees under the same terms and conditions."
The said extension is maintained by Microsoft for Microsoft.
Yet it is fairly common for various devices to use it, and a
popular proprietary operating system expects devices to provide
"OS descriptors", so Linux-based USB gadgets whishing to be able
to talk to a variety of operating systems should be able to provide
the "OS descriptors".
This patch adds optional support for gadgets whishing to expose
the so called "OS String" under index 0xEE of language 0.
The contents of the string is generated based on the qw_sign
array and b_vendor_code.
Interested gadgets need to set the cdev->use_os_string flag,
fill cdev->qw_sign with appropriate values and fill cdev->b_vendor_code
with a value of their choice.
This patch does not however implement responding to any vendor-specific
USB requests."
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
As the SDP protocol use the predefined ep num for communication, we can't
change its name hence reset its ep num while do ep autoconfig, this is
only apply for SPL.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Since some new fields in usb_ep structure been moved to usb_ss_ep.
The CDNS3 gadget driver should replies on this operation to bind the
usb_ss_ep with the endpoint descriptor when function layer uses
usb_ep_autoconfig to add endpoint descriptors to gadget. So that
CDNS3 driver can know the EP information and configure the EP once
the set configuration request is received.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Each array is used only in one file (core.c or ep0.c). Move their content
to correct file, mark them as static and do not export out of current file.
This change allows to decrease size of u-boot.bin as more of those strings
are not used.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reinitialize dfu_env_entities after flashing the 'SCRIPT' entity to
ensure that the potential changes to the 'dfu_alt_info' environment
variable are applied.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Define a new 'SCRIPT' type for DFU entities. The downloaded data are
treated as simple u-boot's scripts and executed with run_command_list()
function.
Flashing the 'SCRIPT' entity might result in changing the 'dfu_alt_info'
environment variable from the flashed script, so add a global variable
for tracking the potential need to reinitialize the dfu_alt_info related
structures.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Define a new 'SKIP' type for the DFU entities. The flashed data for that
entity is simply ignored without returning any error values.
This allows to have one flashing procedure and images for the different
board types or variants, where each board uses only the images relevant
to it and skips the rest. This is especially usefull for the THOR
protocol, which usually transfers more than one file in a single session.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
[mszyprow: rephrased commit message and docs for easier reading, changed
subject to "dfu: add 'SKIP' entity"]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Use the default MMC device set in the command line if entity specifies it
as -1. This allows to use the same dfu_alt_info string for different MMC
devices (like embedded eMMC and external SD card if data layout is the
same on both devices).
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
In case of usb_add_function() failure the error path has an issue,
i.e the global pointer variable is assigned to garbage
Fix the above mentioned issue by assigning pointer to NULL.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
In case of usb_add_function() failure the error path has two issues:
- the potentially allocated structure isn't getting freed
- the global pointer variable is assigned to garbage
Fix the above mentioned issues by freeing memory and assigning NULL.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Casting 32bit int value directly into 64bit unsigned type causes
wrong value for file size equal or larger than 2GB. Fix the wrong
file size by casting uint32_t first.
Fixes: commit 1fe9ae76b1 ("gadget: f_thor: update to support more than 4GB file as thor 5.0")
Reported-by: Junghoon Kim <jhoon20.kim@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
For UBI partitions ("partubi" in dfu_alt_info), dfu_fill_entity_mtd sets
the mtd.ubi flag; however other functions incorrectly check for nand.ubi
instead. Fix this by checking for the correct flag.
Signed-off-by: Guillermo Rodriguez <guille.rodriguez@gmail.com>
Cc: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
The R-Car3 SDHI should set these two bits in DMA_MODE register according
to the specification, to indicate 64bit bus width. No other bus width
options are permitted and the default value is 0, which is incorrect.
Set the bits accordingly.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Provide information about host backed block device.
Mark the device created by 'host bind' as removable.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The UEFI Self Certification Test (SCT) checks the SetTime() service with
the following steps:
* set date
* reset
* check date matches
To be compliant the sandbox should keep the offset to the host RTC during
resets. The implementation uses the environment variable
UBOOT_SB_TIME_OFFSET to persist the offset.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present this function uses the old format for reading hashes. Add
support for the current format.
Add a test while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
The use of pinctrl in the core of driver model is useful but can provoke
some strange behaviour. Add a comment to aid debugging.
Signed-off-by: Simon Glass <sjg@chromium.org>
The current driver name does not match its compatible string, so
of-platdata does not work correctly. Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
These cannot work with of-platdata since they currently need the
devicetree at runtime. Disable the emulators and the sandbox I2C driver
that needs them. We can enable these later, if needed for testing.
Switch the of_plat_parent test over to use a simple bus instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
The EC can store small amounts of data for the benefit of the
verified boot process. Since the EC is seldom reset, this can allow the
AP to store data that survives a reboot or a suspend/resume cycle.
Add support for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
