CID 453851 : sprintf() shouldn't copy from/to tmp
CID 436278 : DHCP6 option_len should be checked before use
Signed-off-by: Sean Edmond <seanedmond@microsoft.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The variable 'node' was already invalid, so using it for further
lookup will not work.
Signed-off-by: Marcus Comstedt <marcus.comstedt@requtech.se>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
We use the terms 'distro' to mean extlinux but they are not really the
same. 'Distro' could refer to any method of booting a distribution,
whereas extlinux is a particular method.
Also we sometimes use syslinux, but it is better to use the same term in
all cases.
Rename distro to syslinux and also update bootstd uses of syslinux to use
extlinux instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
In IPv6, the default gateway and prefix length are determined by receiving
a router advertisement as defined in -
https://www.rfc-editor.org/rfc/rfc4861.
Add support for sending router solicitation (RS) and processing router
advertisements (RA).
If the RA has prefix info option and following conditions are met, then
gatewayip6 and net_prefix_length of ip6addr env variables are initialized.
These are later consumed by IPv6 code for non-local destination IP.
- "Router Lifetime" != 0
- Prefix is NOT link-local prefix (0xfe80::/10)
- L flag is 1
- "Valid Lifetime" != 0
Timing Parameters:
- MAX_RTR_SOLICITATION_DELAY (0-1s)
- RTR_SOLICITATION_INTERVAL (4s) (min retransmit delay)
- MAX_RTR_SOLICITATIONS (3 RS transmissions)
The functionality is enabled by CONFIG_IPV6_ROUTER_DISCOVERY and invoked
automatically from net_init_loop().
Signed-off-by: Ehsan Mohandesi <emohandesi@linux.microsoft.com>
Tested-by: Viacheslav Mitrofanov <v.v.mitrofanov@yadro.com>Reviewed-by:
Tested-by: Viacheslav Mitrofanov <v.v.mitrofanov@yadro.com>
Reviewed-by: Viacheslav Mitrofanov <v.v.mitrofanov@yadro.com>
Tested-by: Sergei Antonov <saproj@gmail.com>
Reviewed-by: Sergei Antonov <saproj@gmail.com>
Introduce reboot, boot and continue commands support to
TCP fastboot by moving existing UDP logic into the common module.
Signed-off-by: Dmitrii Merkurev <dimorinny@google.com>
Cc: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: Simon Glass <sjg@chromium.org>
Сс: Joe Hershberger <joe.hershberger@ni.com>
Сс: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Known limitations are
1. fastboot reboot doesn't work (answering OK but not rebooting)
2. flashing isn't supported (TCP transport only limitation)
The command syntax is
fastboot tcp
Signed-off-by: Dmitrii Merkurev <dimorinny@google.com>
Cc: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: Simon Glass <sjg@chromium.org>
Сс: Joe Hershberger <joe.hershberger@ni.com>
Сс: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Make following changes to unblock TCP fastboot support:
1. Implement being a TCP server support
2. Introduce dedicated TCP traffic handler (get rid of UDP signature)
3. Ensure seq_num and ack_num are respected in net_send_tcp_packet
function (make sure existing wget_cmd code is reflected with the fix)
Signed-off-by: Dmitrii Merkurev <dimorinny@google.com>
Cc: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: Simon Glass <sjg@chromium.org>
Сс: Joe Hershberger <joe.hershberger@ni.com>
Сс: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Adds DHCPv6 protocol to u-boot.
Allows for address assignement with DHCPv6 4-message exchange
(SOLICIT->ADVERTISE->REQUEST->REPLY). Includes DHCPv6 options
required by RFC 8415. Also adds DHCPv6 options required
for PXE boot.
Possible enhancements:
- Duplicate address detection on DHCPv6 assigned address
- IPv6 address assignement through SLAAC
- Sending/parsing other DHCPv6 options (NTP, DNS, etc...)
Signed-off-by: Sean Edmond <seanedmond@microsoft.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
NFSv1 support added by Christian Gmeiner, Thomas Rienoessl,
September 27, 2018. As of now, NFSv3 is the default choice.
if the server does not support NFSv3, we fall back to
versions 2 or 1.
Signed-off-by: Thomas RIENOESSL <thomas.rienoessl@bachmann.info>
The phy_init() is now used only to perform manual relocation of PHY
driver callbacks. Wrap it in ifdeffery and only call it on systems
which still require manual relocation, i.e. m68k .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Move the board_interface_eth_init() into common ethernet uclass code,
since this function could be shared by multiple drivers.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Marek Vasut <marex@denx.de>
This converts 3 usages of this option to the non-SPL form, since there is
no SPL_PHY_FIXED defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 1 usage of this option to the non-SPL form, since there is
no SPL_NETDEVICES defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 3 usages of this option to the non-SPL form, since there is
no SPL_FASTBOOT_FLASH defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
One extra character was being checked in the IPv6 string which caused the
last character of the address to be neither '\0' nor ':'. This raises an
error condition and causes the function to always return an error. This
issue was resolved by this fix.
Signed-off-by: Ehsan Mohandesi <emohandesi@microsoft.com>
Reviewed-by: Viacheslav Mitrofanov <v.v.mitrofanov@yadro.com>
It should be possible to specify a netmask when
setting a static IPv6 address. For example:
setenv ip6addr 2001:cafe:cafe:cafe::100/64
The net_prefix_length and net_ip6 should be updated
properly.
Signed-off-by: Sean Edmond <seanedmond@microsoft.com>
Reviewed-by: Viacheslav Mitrofanov <v.v.mitrofanov@yadro.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
In rfc7440, if an ACK is not received by the server or if the
last data block in a window is dropped, the server will timeout and
retransmit the window. In this case, the block count received will be
less than the internal block count. In this case, the client
should not ACK. ACK should only be sent if the received block
count is greater than the expected block count.
Signed-off-by: Sean Edmond <seanedmond@linux.microsoft.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Allow rcv() and xmit() dsa driver ops to be optional in case a driver
does not care to mangle a packet as in U-Boot only one network port is
enabled at a time and thus no packet mangling is necessary.
Suggested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Add a function to sanity check a dsa driver having proper ops.
Suggested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
In order to ensure that a DSA driver probe gets called before
dsa_ops->port_probe move the port_probe of the cpu_port to
a post-probe function.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
If a DM_MDIO driver is used we need to scan the subnodes as well.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
We need extensions to be set up before we start trying to boot any of the
bootdevs. Add a new priority before all the others for tht sort of thing.
Also add a 'none' option, so that the first one is not 0.
While we are here, comment enum bootdev_prio_t fully and expand the test
for the 'bootdev hunt' command.
Signed-off-by: Simon Glass <sjg@chromium.org>
Sometimes ethernet devices are attached to PCI. Since it is quick to scan,
add this into the ethernet hunter.
Run dhcp to establish the network connection. Drop this from the bootdev
since that is not needed now. Update a log message for clarity.
Signed-off-by: Simon Glass <sjg@chromium.org>
Most tests don't want these and can create a lot of noise. Add a way to
disable them. Use that in tests, with a flag provided to enable them for
tests that need this feature.
Signed-off-by: Simon Glass <sjg@chromium.org>
For bootstd tests it is seldom useful to have ethernet enabled. Add a way
to disable it, so that ethernet operations like tftpboot do nothing.
Signed-off-by: Simon Glass <sjg@chromium.org>
At this point, the remaining places where we have a symbol that is
defined as CONFIG_... are in fairly odd locations. While as much dead
code has been removed as possible, some of these locations are simply
less obvious at first. In other cases, this code is used, but was
defined in such a way as to have been missed by earlier checks. Perform
a rename of all such remaining symbols to be CFG_... rather than
CONFIG_...
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Much of the fastboot code predates the introduction of Kconfig and
has quite a few #ifdefs in it which is unnecessary now that we can use
IS_ENABLED() et al.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> # on vim3l
The compiler complains about the missing declaration of print_size():
net/wget.c:415:3: warning: implicit declaration of function ‘print_size’ [-Wimplicit-function-declaration]
Fix it.
Signed-off-by: Michael Walle <michael@walle.cc>
In ndisc_receive() 7 bytes are copied from a buffer of size 6 to NULL.
net_nd_packet_mac is a pointer. If it is NULL, we should set it to the
address of the buffer with the MAC address.
Addresses-Coverity-ID: 430974 ("Out-of-bounds access")
Fixes: c6610e1d90 ("net: ipv6: Add Neighbor Discovery Protocol (NDP)")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Viacheslav Mitrofanov <v.v.mitrofanov@yadro.com>
IPv6 protocol handler is not terminated with a break statment.
It can lead to running unexpected code.
Signed-off-by: Viacheslav Mitrofanov <v.v.mitrofanov@yadro.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This converts the following to Kconfig:
CONFIG_GATEWAYIP
CONFIG_HOSTNAME
CONFIG_IPADDR
CONFIG_NETMASK
CONFIG_ROOTPATH
CONFIG_SERVERIP
CONFIG_UBOOTPATH
To do this, we introduce a CONFIG_USE_ form of each of the above and
change include/env_default.h to test for that to be set before setting a
value. Further, we don't want to stringify the IP address related values
as they are now properly strings via Kconfig.
Signed-off-by: Tom Rini <trini@konsulko.com>
As there are no more non-DM_ETH cases for networking, remove this legacy
file and update the Makefile to match current usage.
Signed-off-by: Tom Rini <trini@konsulko.com>
Implement ping6 command to ping hosts using IPv6. It works the same way as
an ordinary ping command. There is no ICMP request so it is not possible
to ping our host. This patch adds options in Kconfig and Makefile to
build ping6 command.
Series-changes: 3
- Added structures and functions descriptions
- Added to ping6_receive() return value instead of void
Series-changes: 4
- Fixed structures and functions description style
Signed-off-by: Viacheslav Mitrofanov <v.v.mitrofanov@yadro.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The command tftpboot uses IPv4 by default. Add the possibility to use IPv6
instead. If an address in the command is an IPv6 address it will use IPv6
to boot or if there is a suffix -ipv6 in the end of the command it also
force using IPv6. All other tftpboot features and parameters are left
the same.
Signed-off-by: Viacheslav Mitrofanov <v.v.mitrofanov@yadro.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add net_ip6_handler (an IPv6 packet handler) into net_loop. Add
neighbor discovery mechanism into network init process. That is the
main step to run IPv6 in u-boot. Now u-boot is capable to use NDP and
handle IPv6 packets.
Signed-off-by: Viacheslav Mitrofanov <v.v.mitrofanov@yadro.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Functions that were exposed in "net: ipv6: Add IPv6 basic primitives"
had only empty implementations and were exposed as API for futher
patches. This patch add implementation of these functions. Main
functions are: net_ip6_handler() - IPv6 packet handler for incoming
packets; net_send_udp_packet6() - make up and send an UDP packet;
csum_ipv6_magic() - compute checksum of IPv6 "psuedo-header" per RFC2460
section 8.1; ip6_addr_in_subnet() - check if an address is in our
subnet. Other functions are auxiliary.
Series-changes: 3
- Added comments
- Fixed style problems
- Fixed return codes instead of -1
Signed-off-by: Viacheslav Mitrofanov <v.v.mitrofanov@yadro.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Implement basic of NDP. It doesn't include such things as Router
Solicitation, Router Advertisement and Redirect. It just has Neighbor
Solicitation and Neighbor Advertisement. Only these two features are used
in u-boot IPv6. Implementation of some NDP functions uses API that was
exposed in "net: ipv6: Add IPv6 basic primitives".
Also this patch inlcudes update in Makefile to build NDP.
Series-changes: 3
- Added structures and functions descriptions
- Fixed style problems
Series-changes: 4
- Fixed structures and functions description style
Signed-off-by: Viacheslav Mitrofanov <v.v.mitrofanov@yadro.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add options to Makefile and Kconfig file to build IPv6
Series-changes: 3
- Added help for IPv6 support
Signed-off-by: Viacheslav Mitrofanov <v.v.mitrofanov@yadro.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch is a collection of basic primitives that are prerequisite for
further IPv6 implementation.
There are structures definition such as IPv6 header, UDP header
(for TFTP), ICMPv6 header. There are auxiliary defines such as protocol
codes, padding, struct size and etc. Also here are functions prototypes
and its empty implementation that will be used as API for further patches.
Here are variables declaration such as IPv6 address of our host,
gateway, ipv6 server.
Series-changes: 3
- Added functions and structures descriptions
- Removed enums ND_OPT_*. It will be moved into further patches
- Substituted -1 for error codes
Series-changes: 4
- Changed functions and structures description style
Signed-off-by: Viacheslav Mitrofanov <v.v.mitrofanov@yadro.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The symbol CONFIG_NET_DEVICES does not exist.
The correct name is CONFIG_NETDEVICES.
Fixes: 77b5c4a5b1 ("efi_loader: Let networking support depend on NETDEVICES")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
This commit adds a simple wget command that can download files
from http server.
The command syntax is
wget ${loadaddr} <path of the file from server>
Signed-off-by: Duncan Hare <DuncanCHare@yahoo.com>
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Currently file transfers are done using tftp or NFS both
over udp. This requires a request to be sent from client
(u-boot) to the boot server.
The current standard is TCP with selective acknowledgment.
Signed-off-by: Duncan Hare <DH@Synoia.com>
Signed-off-by: Duncan Hare <DuncanCHare@yahoo.com>
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
