For sf commands, when '0' length is passed for erase, update, write or
read, there might be undesired results. Ideally '0' length means nothing to
do.
So print 'ERROR: Invalid size 0' and return cmd failure when length '0' is
passed to sf commands. Same thing applies for nand commands also.
Example:
ZynqMP> sf erase 0 0
ERROR: Invalid size 0
ZynqMP> sf write 10000 0 0
ERROR: Invalid size 0
ZynqMP> sf read 10000 0 0
ERROR: Invalid size 0
ZynqMP> sf update 1000 10000 0
ERROR: Invalid size 0
ZynqMP>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230516115236.22458-1-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
The ubifsload command is truncating any address above 4GiB as it casts
this address to an u32, instead of using an unsigned long which most of
the other load commands do. Change this to an unsigned long to allow
loading into high memory for boards which use these areas.
Fixes the following error:
=> ubifsload 0x2100000000 /boot/Image.lzma
Loading file '/boot/Image.lzma' to addr 0x00000000...
Unhandled exception: Store/AMO access fault
Signed-off-by: Ben Dooks <ben.dooks@sifive.com>
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
In a few cases the error handling is not quite right. Make sure we
return the actual error in distro_efi_read_bootflow_file() rather than
-EINVAL. Return -IO when a file cannot be read. Also show the error name
if available.
This does not change operation, but does make it easier to diagnose
problems.
Signed-off-by: Simon Glass <sjg@chromium.org>
The patch to relax flag requirements was not accepted[1], so we still have
to have separate bootcommands depending on CMD_BOOTFLOW_FULL.
The previous attempt at this did not work, since it used the wrong name
for the options.
Fix this and change the message to mention BOOTSTD_FULL since this affects
not just the flags, but all functionality, so is more likely what the user
wants.
Drop the useless condition on CMD_BOOTFLOW_FULL while we are here.
[1] https://patchwork.ozlabs.org/project/uboot/patch/20230329071655.1959513-2-sjg@chromium.org/
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes: a91492b6e9 ("bootstd: Provide a default command")
This should be declared in a header file so that type-checking works
correctly.
Add a single declaration to usb.h and remove the others.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
* When called from efi_dp_from_name() we miss to append the filename
for non-block devices.
* expand_media_path() could be simplified by using efi_dp_from_file to
prepend the device path of the boot device.
This can be avoided by passing a device path to efi_dp_from_file() instead
of a block device descriptor and a partition number.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Sometimes coreboot adds new tags that U-Boot does not know about. These
are silently ignored, but it is useful to at least know what we are
missing.
Add a way to collect this information. For Brya it shows:
Unimpl. 38 41 37 34 42 40
These are:
LB_TAG_PLATFORM_BLOB_VERSION
LB_TAG_ACPI_CNVS
LB_TAG_FMAP
LB_TAG_VBOOT_WORKBUF
LB_TAG_TYPE_C_INFO
LB_TAG_BOARD_CONFIG
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
At present any ACPI tables created by prior-stage firmware are ignored.
It is useful to be able to view these in U-Boot.
Pick this up from the sysinfo tables and display it with the cbsysinfo
command. This allows the 'acpi list' command to work when booting from
coreboot.
Adjust the global_data condition so that acpi_start is available even if
table-generation is disabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
This is useful for other features. Move the function into library code
so it can be used outside just the 'acpi' command.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
We have several Kconfig options for ACPI, but all relate to specific
functions, such as generating tables and AML code.
Add a new option which controls including basic ACPI library code,
including the lib/acpi directory. This will allow us to add functions
which are available even if table generation is not supported.
Adjust the command to avoid a build error when ACPIGEN is not enabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When U-Boot did not do the MP init, we don't get an actual CPU number
here. Skip printing it in that case.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Move the handler for "tlv_eeprom dev X" command to the beginning of
do_tlv_eeprom, to allow using it before issuing a "read" command for
currently selected eeprom.
Also remove the check if eeprom exists, since that can only work after
the first execution of read_eeprom triggered device lookup.
Instead accept values up to the defined array size (MAX_TLV_DEVICES).
Signed-off-by: Josua Mayer <josua@solid-run.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
When tlv eeprom does not exist, return error code instead of quietly
making up tlv structure in memory.
Signed-off-by: Josua Mayer <josua@solid-run.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
has_been_read is only used as an optimization for do_tlv_eeprom.
Explicitly use and set inside this function, thus making read_eeprom
stateless.
Signed-off-by: Josua Mayer <josua@solid-run.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Make tlv_eeprom command device selection an explicit parameter of all
function calls.
Signed-off-by: Josua Mayer <josua@solid-run.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
In IPv6, the default gateway and prefix length are determined by receiving
a router advertisement as defined in -
https://www.rfc-editor.org/rfc/rfc4861.
Add support for sending router solicitation (RS) and processing router
advertisements (RA).
If the RA has prefix info option and following conditions are met, then
gatewayip6 and net_prefix_length of ip6addr env variables are initialized.
These are later consumed by IPv6 code for non-local destination IP.
- "Router Lifetime" != 0
- Prefix is NOT link-local prefix (0xfe80::/10)
- L flag is 1
- "Valid Lifetime" != 0
Timing Parameters:
- MAX_RTR_SOLICITATION_DELAY (0-1s)
- RTR_SOLICITATION_INTERVAL (4s) (min retransmit delay)
- MAX_RTR_SOLICITATIONS (3 RS transmissions)
The functionality is enabled by CONFIG_IPV6_ROUTER_DISCOVERY and invoked
automatically from net_init_loop().
Signed-off-by: Ehsan Mohandesi <emohandesi@linux.microsoft.com>
Tested-by: Viacheslav Mitrofanov <v.v.mitrofanov@yadro.com>Reviewed-by:
Tested-by: Viacheslav Mitrofanov <v.v.mitrofanov@yadro.com>
Reviewed-by: Viacheslav Mitrofanov <v.v.mitrofanov@yadro.com>
Tested-by: Sergei Antonov <saproj@gmail.com>
Reviewed-by: Sergei Antonov <saproj@gmail.com>
Known limitations are
1. fastboot reboot doesn't work (answering OK but not rebooting)
2. flashing isn't supported (TCP transport only limitation)
The command syntax is
fastboot tcp
Signed-off-by: Dmitrii Merkurev <dimorinny@google.com>
Cc: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: Simon Glass <sjg@chromium.org>
Сс: Joe Hershberger <joe.hershberger@ni.com>
Сс: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Adds commands to support DHCP and PXE with IPv6.
New configs added:
- CMD_DHCP6
- DHCP6_PXE_CLIENTARCH
- DHCP6_PXE_DHCP_OPTION
- DHCP6_ENTERPRISE_ID
New commands added (when IPv6 is enabled):
- dhcp6
- pxe get -ipv6
- pxe boot -ipv6
Signed-off-by: Sean Edmond <seanedmond@microsoft.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Fix "setenv gatewayip6".
Synchronize IPv6 local variables with environment variables
in netboot_update_env()
Signed-off-by: Sean Edmond <seanedmond@microsoft.com>
Instead of always printing ethaddr of MAC 0, print eth%daddr of the current MAC.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move all the network information printing into print_eth(),
no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Map fdt_blob and new_fdt to sysmem, otherwise $fdtcontroladdr
and bdinfo output do not match and the bdinfo output address
is not a valid address accessible via sandbox memory accessors.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
When building this with clang, we get a warning such as:
cmd/bootflow.c:412:27: warning: variable 'bflow' is uninitialized when used here [-Wuninitialized]
printf("Selected: %s\n", bflow->os_name ? bflow->os_name : bflow->name);
^~~~~
And a suggestion to just initialize bflow to NULL. This would however
would be ensuring a bad dereference. Instead, looking at the function we
rework things so that when CONFIG_EXPO is not enabled (and so, no UI) we
error early and would never reach this point in the code. Simplify the
rest slightly as well while at this.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present the code does ide_init() as a separate operation, then calls
device_probe() to copy over the information. We can call ide_init() from
probe just as easily.
The only difference is that using 'ide init' twice will do nothing.
However it already fails to copy over the new data in that case, so the
effect is the same. For now, unbind the block devices and remove the IDE
device, which causes the bus to be probed again. Later patches will fix
this up fully, so that all blk_desc data is copied across.
Since ide_reset() is only called from ide_init(), there is no need to init
the ide_dev_desc[] array. This is already done at the end of ide_init() so
drop this code.
The call to uclass_first_device() is now within the probe() function of
the same device, so does nothing. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Enable some messages that might provide hints, but only for
CMD_BOOTFLOW_FULL since otherwise the -l flag is not available.
Signed-off-by: Simon Glass <sjg@chromium.org>
Suggested-by: Tom Rini <trini@konsulko.com>
To enable splash screen at SPL, need to compile cmd/bmp.c which also
includes bmp commands, since SPL doesn't use commands split bmp.c into
common/bmp.c which includes all bmp functions and cmd/bmp.c which only
contains bmp commands.
Add function delclaration for bmp_info in video.h.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Find SATA block device by blk_get_devnum_by_uclass_id() function and read
from it the real block size of the SATA disk. In case of error, fallback
back to 512 bytes.
Signed-off-by: Pali Rohár <pali@kernel.org>
Numeric return values may cause strange errors line:
exit not allowed from main input shell.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Mask macro PART_ACCESS_MASK filter out access bits of emmc register and
macro EXT_CSD_EXTRACT_BOOT_PART() extracts boot part bits of emmc register.
So use EXT_CSD_EXTRACT_BOOT_PART() when extracting boot partition.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
If console multiplexing in enabled (CONFIG_CONSOLE_MUX=y), the output of
the coninfo command should show the file association (stdin, stderr,
stdout) for all devices not only the default ones.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add the 2048 game, a good demo of ANSI sequences and a way to waste a
little time.
Bring it it from Barebox, modified for code style.
Signed-off-by: Simon Glass <sjg@chromium.org>
Compiling with CONFIG_CMD_SCSI=y, CONFIG_SCSI results in
cmd/scsi.c:46: undefined reference to `scsi_scan'
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a missing fallthrough macro to avoid a -Wimplicit-fallthrough warning.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
gcc does not understand /* FALL TROUGH */ and emits a warning:
cmd/date.c: In function ‘do_date’:
cmd/date.c:62:20: warning:
this statement may fall through [-Wimplicit-fallthrough=]
62 | if (strcmp(argv[1],"reset") == 0) {
| ^
cmd/date.c:102:9: note: here
102 | case 1: /* get date & time */
| ^~~~
Use the fallthrough macro instead.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a frontend for the blkmap subsystem. In addition to the common
block device operations, this allows users to create and destroy
devices, and map in memory and slices of other block devices.
With that we support two primary use-cases:
- Being able to "distro boot" from a RAM disk. I.e., from an image
where the kernel is stored in /boot of some filesystem supported
by U-Boot.
- Accessing filesystems not located on exact partition boundaries,
e.g. when a filesystem image is wrapped in an FIT image and stored
in a disk partition.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Ensure that the memory destination/source addresses of block
read/write operations are mapped in before access. Currently, this is
only needed on sandbox builds.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Enable the support for boot image header version 3 and 4
using abootimg command.
In order to use version 3 or 4:
1- Vendor boot image address should be given to abootimg cmd.
abootimg addr $1 $vendor_boot_load_addr
2- "ramdisk_addr_r" env variable (ramdisk address) should be set to host
the ramdisk : generic ramdisk + vendor ramdisk
Replace "struct andr_boot_img_hdr_v0*" by "void *" in
some functions since v3 and v4 are now supported as well.
Signed-off-by: Safae Ouajih <souajih@baylibre.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Introduce vendor boot image for version 3 and 4 of boot image header.
The vendor boot image will hold extra information about kernel, dtb
and ramdisk.
This is done to prepare for boot image version 3 and 4 support.
Signed-off-by: Safae Ouajih <souajih@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Move from andr_boot_img_hdr_v0 to andr_image_data
structure to prepare for boot image header
version 3 and 4.
Signed-off-by: Safae Ouajih <souajih@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
With the new vendor boot image introduced in versions 3 and 4
of boot image header, the header check must be done for both boot
image and vendor boot image. Thus, replace android_image_check_header()
by is_android_boot_image_header() to only refer to boot image header check.
Signed-off-by: Safae Ouajih <souajih@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Vendor boot image is introduced in boot image header
version 3 and 4. Please check [1] for more details.
To prepare for boot image v3/v4 support, allow the abootimg command
to store the vendor_boot image address.
Full support for this new format will be done in a future patch.
Link:[1] https://source.android.com/docs/core/architecture/bootloader/partitions/vendor-boot-partitions
Signed-off-by: Safae Ouajih <souajih@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Android introduced boot header version 3 or 4.
The header structure change with version 3 and 4 to support
the new updates such as:
- Introducing Vendor boot image: with a vendor ramdisk
- Bootconfig feature (v4)
Change andr_img_hdr struct name to maintain support for version v0,
v1 and v2 while introducing version 3 and 4.
Signed-off-by: Safae Ouajih <souajih@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
64597346 "fdt: Add -q option to fdt addr for distro_bootcmd" introduced
the -q option for fdt addr, which sets the current working fdt address
without printing any output.
baf41410 "fdt: Show a message when the working FDT changes" made the
utility function set_working_fdt_addr (in cmd/fdt.c) output a message
on each invocation, even if called via fdt addr -q, in which case its
output is now slightly noisier.
To fix this, split out set_working_fdt_addr into set_working_fdt_addr
plus the static function set_working_fdt_addr_quiet.
set_working_fdt_addr_quiet can be called by "quiet" fdt cmd logic and
set_working_fdt_addr is exported (as before) to other boot logic. The
latter calls the former.
Remove the assertion from the fdt addr test case when calling with the
-q argument.
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
The 'fdt get addr' and 'env get size' is always assumed to be hex
value, drop the prefix, and outright switch to env_set_hex(). Since
this might break existing users who depend on the existing behavior
with 0x prefix, this is a separate patch.
Revert if this breaks anything.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch introduses config which allows interrupt run of usb
mass storage with any key. This is especially useful on devices
with limited input capabilities like tablets and smatphones which
have only gpio keys in direct access.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
