As reported by Coverity Scan for Das U-Boot, the 'less-than-zero'
comparison of an unsigned value is never true.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
When CONFIG_USE_DEFAULT_ENV_FILE=y and the file
CONFIG_DEFAULT_ENV_FILE is empty (or at least doesn't contain any
non-comment, non-empty lines), we end up feeding nothing into xxd,
which in turn then outputs nothing. Then blindly appending ", 0x00"
means that we end up trying to compile (roughly)
const char defaultenv[] = { , 0x00 }
which is of course broken.
To fix that, change the frobbing of the text file so that we always
end up printing an extra empty line (which gets turned into that extra
nul byte we need) - that corresponds better to the binary format
consisting of a series of key=val nul terminated strings, terminated
by an empty string.
Reported-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
There are some cases where decompressed sectors can have padding zeros.
In kernel code, we have lines to address such situation:
/*
* btrfs_getblock is doing a zero on the tail of the page too,
* but this will cover anything missing from the decompressed
* data.
*/
if (bytes < destlen)
memset(kaddr+bytes, 0, destlen-bytes);
kunmap_local(kaddr);
But not in U-boot code, thus we have some reports of U-boot failed to
read compressed files in btrfs.
Fix it by doing the same thing of the kernel, for both inline and
regular compressed extents.
Reported-by: Matwey Kornilov <matwey.kornilov@gmail.com>
Link: https://bugzilla.suse.com/show_bug.cgi?id=1183717
Fixes: a26a6bedaf ("fs: btrfs: Introduce btrfs_read_extent_inline() and btrfs_read_extent_reg()")
Signed-off-by: Qu Wenruo <wqu@suse.com>
When zImage support was added to SPL, the messages were hidden to reduce
code size. However, the wrong config symbol was used. Since this file is
only built when CONFIG_SPL_FRAMEWORK=y, the messages were always hidden.
Use the correct symbol so the messages are printed in U-Boot proper.
Also use IS_ENABLED to drop the #ifdef.
Fixes: 431889d6ad ("spl: zImage support in Falcon mode")
Signed-off-by: Samuel Holland <samuel@sholland.org>
When flush_cache() is called during boot on our ~7M kernel image, the
hundreds of thousands of WATCHDOG_RESET calls end up adding
significantly to boottime. Flushing a single cache line doesn't take
many microseconds, so doing these calls for every cache line is
complete overkill.
The generic watchdog_reset() provided by wdt-uclass.c actually
contains some rate-limiting logic that should in theory mitigate this,
but alas, that rate-limiting must be disabled on powerpc because of
its get_timer() implementation - get_timer() works just fine until
interrupts are disabled, but it just so happens that the "big"
flush_cache() call happens in the part of bootm where interrupts are
indeed disabled. [1] [2] [3]
I have checked with objdump that the generated code doesn't change
when this option is left at its default value of 0: gcc is smart
enough to see that the ">=" comparison is tautologically true, hence
all assignments to "flushed" are eliminated as dead stores.
On our board, setting the option to something like 65536 ends up
reducing total boottime by about 0.8 seconds.
[1] https://patchwork.ozlabs.org/project/uboot/patch/20200605111657.28773-1-rasmus.villemoes@prevas.dk/
[2] https://lists.denx.de/pipermail/u-boot/2021-April/446906.html
[3] https://lists.denx.de/pipermail/u-boot/2021-April/447280.html
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
CONFIG_5xx hasn't existed since commit 5025897774 (powerpc, 5xx:
remove support for 5xx). Remove this last mention of it.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Having WATCHDOG_RESET() called automatically from the timer interrupt
runs counter to the idea of a watchdog device - if the board runs into
an infinite loops with interrupts still enabled, the watchdog will
never fire.
When using CONFIG_(SPL_)WDT, the watchdog_reset function is a lot more
complicated than just poking a few SOC-specific registers - it
involves accessing all kinds of global data, and if the interrupt
happens at the wrong time (say, in the middle of an WATCHDOG_RESET()
call from ordinary code), that can end up corrupting said global data.
Allow the board to opt out of calling WATCHDOG_RESET() from the timer
interrupt handler by setting CONFIG_SYS_WATCHDOG_FREQ to 0 - as that
setting is currently nonsensical (it would be compile-time
divide-by-zero), it cannot affect any existing boards.
Add documentation for both the existing and extended meaning of
CONFIG_SYS_WATCHDOG_FREQ.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
The code, which is likely copied from arch/powerpc/lib/interrupts.c,
lacks a fallback definition of CONFIG_SYS_WATCHDOG_FREQ and refers to
a non-existing timestamp variable - obviously priv->timestamp is
meant.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Some boards don't work with the rate-limiting done in the generic
watchdog_reset() provided by wdt-uclass.
For example, on powerpc, get_timer() ceases working during bootm since
interrupts are disabled before the kernel image gets decompressed, and
when the decompression takes longer than the watchdog device
allows (or enough of the budget that the kernel doesn't get far enough
to assume responsibility for petting the watchdog), the result is a
non-booting board.
As a somewhat hacky workaround (because DT is supposed to describe
hardware), allow specifying hw_margin_ms=0 in device tree to
effectively disable the ratelimiting and actually ping the watchdog
every time watchdog_reset() is called. For that to work, the "has
enough time passed" check just needs to be tweaked a little to allow
the now==next_reset case as well.
Suggested-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Stefan Roese <sr@denx.de>
Enable CONFIG_SYS_FLASH_PROTECTION on Salvator-X(S), ULCB, Ebisu,
which means the Spansion HF PPB protection bits can be operated
using the 'protect' U-Boot command.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The clock driver used a heavy-handed approach where it turned off
all available clocks, while also possibly setting bits which are not
documented in the R-Car datasheet. Update the tables so that only
the bits which are documented are set or cleared when tearing down
the clock driver.
Note that the only clock left running before booting Linux are now
MFIC, INTC-AP, INTC-EX and SCIF2 / SCIF0 on V3x.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Import updated devicetree files from the Linux v5.12 release.
Besides some node and audio port renames this changes the PHY modes to
either rgmii-id or rgmii-txid. From the board files the Pinephone sees
a lot of updates.
This also adds the long missing USB PHY property for controller 0, which
allows the U-Boot PHY driver to eventually use port 0 in host mode
(pending another U-Boot patch).
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Update R40 .dts{,i} and dt-binding headers to current version from kernel.
Files taken from Linux 5.12-rc1 release
(commit fe07bfda2fb9cdef8a4d4008a409bb02f35f1bd8)
Signed-off-by: Ivan Uvarov <i.uvarov@cognitivepilot.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Commit eb5a2b6710 ("net: sun8i-emac: Determine pinmux based on SoC,
not EMAC type") switched the pinmux setup over to look at
CONFIG_MACH_SUN* symbols, to find the appropriate mux value.
Unfortunately this patch missed to check for the H5, which is
pin-compatible to the H3, but uses a different Kconfig symbol (because
it has ARMv8 vs. ARMv7 cores).
Replace the pure SUN8I_H3 symbol with the joint SUNXI_H3_H5 one, which is
there to cover the peripherals common to both SoCs.
Also explicitly list each supported SoC, and have an error message in the
fallback case, to avoid those problems in the future.
This fixes Ethernet support on all H5 boards.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Samuel Holland <samuel@sholland.org> # Orange Pi PC2
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
This patch adds support for the following I2C devices connected to
I2C bus 0 on the Octeon EBB7304:
- Dallas DS1337 RTC
- TLV EEPROM
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
We already have a clock driver for MIPS Octeon. This patch changes the
Octeon DT nodes to supply the clock property via the clock driver
instead of using an hard-coded value, which is not correct in all cases.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Add the AHCI compatible SATA DT node to the Octeon CN73xx dtsi file.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Otherwise the output will look like this on MIPS Octeon NIC23:
Device 0: (0:0) Vendor: ATA Prod.: aSDnsi klUrt aII Rev: 4X11
Type: Hard Disk
Capacity: 457862.8 MB = 447.1 GB (937703088 x 512)
instead of this version:
Device 0: (0:0) Vendor: TA Prod.: SanDisk Ultra II Rev: X411
Type: Hard Disk
Capacity: 457862.8 MB = 447.1 GB (937703088 x 512)
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This patch adds a few missing virt_to_phys() to use the correct physical
address for DMA operations in the common AHCI code. This is done to
support the big-endian MIPS Octeon platform.
Additionally the code a cleaned up a bit (remove some empty lines) and
made a bit better readable.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This patch enables the usage of the MVEBU AHCI/SATA driver. The only
changes necessary to support MIPS Octeon via DT based probing are, to
add the compatible DT property and the use of dev_remap_addr() so that
the correct mapped address is used in the Octeon case (phys != virt).
Please note that this driver supports the usage of the "scsi" command
and not the "sata" command, since it does not provide an own "scan"
function, which is needed for the "sata" cmd support.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
For easy AHCI/ SATA integration, this patch adds board_ahci_enable()
for the MVEBU AHCI driver, which will be used by this platform. This
platform specific "enable" function will setup the proper endian
swapping in the AHCI controller so that it can be used by the common
AHCI code.
Additionally the endian swizzle entry for AHCI in
octeon_should_swizzle_table[] is removed, as this enabled the original
lowlevel code function, e.g. octeon_configure_qlm(), for the QLM setup
to work correctly.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This patch adds the necessary platform infrastructure code, so that the
MIPS Octeon drivers "serial_octeon_pcie_console" & "serial_bootcmd" can
be used. This is e.g. the bootmem initialization in a compatible way to
the Marvell 2013 U-Boot, so that the exisiting PC remote tools like
"oct-remote-console" & "oct-remote-load" can be used. This is be done in
the newly introduced arch_misc_init(), which calls the necessary init
functions when enabled.
These patches are in preparation for the MIPS Octeon NIC23 board
support, which is a desktop PCIe target board enabling these features.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This patch adds the PCI bootcmd feature for MIPS Octeon, which will be
used by the upcoming Octeon III NIC23 board support. It enables the use
of the "oct-remote-load" and "oct-remote-bootcmd" on host PC's to
communicate with the PCIe target and load images into the onboard
memory and issue commands.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This patch adds the PCI remote console feature for MIPS Octeon, which
will be used by the upcoming Octeon III NIC23 board support. It enables
the use of the "oct-remote-console" tool on host PC's to communicate
with the PCIe target.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
As DEBUG is no Kconfig symbol, we can't use the IS_ENABLED() macros.
This patch switches to the unfortunately necessary #ifdef usage again
to make it work correctly.
Signed-off-by: Stefan Roese <sr@denx.de>
While porting from the Marvell source, I introduced a bug by misplacing
the parenthesis. This patch fixes this issue.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch changes the MIPS Octeon defconfig to enable some features
for PCIe enablement. This includes CONFIG_BOARD_LATE_INIT to call the
board specific serdes init code.
With these features enabled, the serdes and PCIe driver including the
Intel E1000 driver can be tested on the Octeon EBB7304.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds the PCIe host controller driver for MIPS Octeon II/III.
The driver mainly consist of the PCI config functions, as all of the
complex serdes related port / lane setup, is done in the serdes / pcie
code available in the "arch/mips/mach-octeon" directory.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This patch adds the board specific QLM/DLM init code to the Octeon 3
EBB7304 board. The configuration of each port is read from the
environment exactly as done in the 2013 U-Boot version to keep the
board and it's configuration compatible.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds the newly added C files to the Makefile to enable
compilation. This is done in a separate step, to not introduce build
breakage while adding the single files with potentially missing
externals.
Signed-off-by: Stefan Roese <sr@denx.de>
Import octeon_qlm.c from 2013 U-Boot. It will be used by the later
added drivers to support PCIe and networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import octeon_fdt.c from 2013 U-Boot. It will be used by the later
added drivers to support PCIe and networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-qlm.c from 2013 U-Boot. It will be used by the later
added drivers to support PCIe and networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-pcie.c from 2013 U-Boot. It will be used by the later
added drivers to support PCIe and networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-helper.c from 2013 U-Boot. It will be used by the later
added drivers to support PCIe and networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-helper-util.c from 2013 U-Boot. It will be used by the later
added drivers to support PCIe and networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-helper-jtag.c from 2013 U-Boot. It will be used by the later
added drivers to support PCIe and networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-helper-fdt.c from 2013 U-Boot. It will be used by the later
added drivers to support PCIe and networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-helper-cfg.c from 2013 U-Boot. It will be used by the later
added drivers to support PCIe and networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
To match all other cvmx-* header, this patch moves the already existing
cvmx-lmcx-defs.h header one directory up.
Signed-off-by: Stefan Roese <sr@denx.de>
With the newly added headers and their restructuring (which macro is
defined where), some changes in the already existing Octeon files are
necessary. This patch makes the necessary changes.
Signed-off-by: Stefan Roese <sr@denx.de>
Import misc remaining header files from 2013 U-Boot. These will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
