This bug was detected on the LWMON5 target which has 2 Intel 16bit wide
flash chips connected to a 32bit wide port.
Signed-off-by: Stefan Roese <sr@denx.de>
The bash builtin versions of the "test" (resp. "[") command allow
using "==" for string comparisons, but POSIX compatible implemen-
tations (like /usr/bin/test) insist on using "=" only. On such systems
you will see:
$ /usr/bin/test a == a && echo OK
/usr/bin/test: ==: binary operator expected
This patch fixes Makefiles and scripts to use POSIX style.
Signed-off-by: Wolfgang Denk <wd@denx.de>
This bug was detected on the LWMON5 target which has 2 Intel 16bit wide
flash chips connected to a 32bit wide port.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch brings the PMC440 board configuration file.
Finally it enables the PMC440 board support.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
This patch adds the first files for the new esd PMC440 boards.
The next two patches will complete the PMC440 board support.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
This patch fixes esd's LCD dectection code to work correctly with
newer gcc versions.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
In an attmemt to clean up the 4xx start.S file, I removed the enabling
of the internal 405EP PCI arbiter. This is needed for multiple other
405EP platforms, like most of the esd 405EP. Now the internal PCI
arbiter is enabled again per default as it has been before.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
This board never left prototyping state and it
became a millstone round my neck. So remove it.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
These patches add support for the PPC440EPx-based "Korat" board to
U-Boot. They are based primarily on support for the Sequoia board.
Signed-off-by: Larry Johnson <lrj@acm.org>
This patch adds SPD DDR2 support for the 440EPx ("Denali") SDRAM
controller. It should also work on the 440GRx. It is based on the DDR2
SPD code for the 440EP/440EPx, but makes no provision for DDR1 support.
This code has been tested on prototype Korat boards with three Kingston
DIMMS: 512 MiB ECC (one rank), 512 MiB non-ECC (one rank) and 1 GiB ECC
(two ranks). The Korat board has a single DIMM socket, but support has
been provided (though not tested) for boards with two DIMM sockets.
Signed-off-by: Larry Johnson <lrj@acm.org>
This patch creates a non-board-specific file for performing the SDRAM
data-eye search. It also adds ECC error checking to the test of valid
data on readback when ECC is enabled.
Signed-off-by: Larry Johnson <lrj@acm.org>
This patch adds the Denali SDRAM controller definitions to "ppc440.h".
It also fixes two typos in the definitions, so the board-specific
"sdram.h" files containing these definitions are also fixed to avoid
compiler warnings.
Signed-off-by: Larry Johnson <lrj@acm.org>
This patch adds a new switch: "CONFIG_PHY_DYNAMIC_ANEG". When this symbol
is defined, the PHY will advertise it's capabilities for autonegotiation
based on the capabilities shown in the PHY's status registers, including
1000BASE-X. When "CONFIG_PHY_DYNAMIC_ANEG" is not defined, the PHY will
advertise hard-coded capabilities, as before.
Signed-off-by: Larry Johnson <lrj@acm.org>
This driver is based on the driver for the M41T11. In the intended
application, the RTC will be powered by a large capacitor, rather than a
battery. The driver therefore checks to see whether the RTC has lost
power. The chip's OUT bit is normally reset from its power-up state. If
the OUT bit is read as set, or if the date and time are not valid, then the
RTC is assumed to have lost power, and its date and time are reset to
1900-01-01 00:00:00.
Support for adjusting the speed of the clock to improve accuracy is
provided through an environment variable.
Signed-off-by: Larry Johnson <lrj@acm.org>
On Sequoia & LWMON5 the virtual address of the POST cache test is now
moved to a bigger address. This enables usage of more memory on those
boards.
Signed-off-by: Stefan Roese <sr@denx.de>
As repoted by Larry Johnson, running "diag run cache" caused a crash
in U-Boot. This problem was introduced by a patch that removed the
TLB entry for the cache test after the test has completed. Since this
TLB was only setup once, a 2nd attempt to run this cache test
failed with a crash. Now this TLB entry is created every time the
routine is called.
Signed-off-by: Stefan Roese <sr@denx.de>
Now the cpu node setup ("timebase-frequency" and "clock-frequency") is
without using the absolute path to the cpu node. This makes it possible
to use this U-Boot version with both versions of cpu-node naming
"cpu@0" and the former "PowerPC,440EPx@0".
Signed-off-by: Stefan Roese <sr@denx.de>
ppc4xx clear_bss() fails if BSS segment size is not
divisible by 4 without remainder. This patch provides
fix for this problem.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
When using dhcp/bootp the "netmask" environment variable is not
set because CONFIG_BOOTP_SUBNETMASK is not defined. But usually this is
desireable, so the following patch adds this this option to the board
config.
Signed-off-by: Markus Klotzbuecher <mk@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch allows the ECC POST to be used for different boards with the
PPC440 Denali SDRAM controller. Modifications include skipping the test
if ECC is not enabled (as for non-ECC DIMMs) and adding synchronization
to prevent timing errors.
Signed-off-by: Larry Johnson <lrj@acm.org>
flush + invalidate_dcache_range() expect the start and stop+1 address.
So the stop address is the first address behind (!) the range.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
By using aliases in the dts file, the ethernet node fixup is
much easier with the recently added functions.
Please note that the dts file needs the aliases for this to work.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch update the 4xx fdt support. It enabled fdt booting
on the AMCC Kilauea and Sequoia for now. More can follow later
quite easily.
Signed-off-by: Stefan Roese <sr@denx.de>
The check for an sufficiently erased destination was missing in the
buffered write function of the cfi flash driver (when
CFG_FLASH_USE_BUFFER_WRITE is defined). This patch adds this check to that
writing to such a region will fail with the currect error message.
Signed-off-by: Stefan Roese <sr@denx.de>
