Commit graph

220 commits

Author SHA1 Message Date
Chunhe Lan
9c3f77eb3b fsl_i2c: add workaround for the erratum I2C A004447
This workaround is for the erratum I2C A004447. Device reference
manual provides a scheme that allows the I2C master controller
to generate nine SCL pulses, which enable an I2C slave device
that held SDA low to release SDA. However, due to this erratum,
this scheme no longer works. In addition, when I2C is used as
a source of the PBL, the state machine is not able to recover.

At the same time, delete the reduplicative definition of SVR_VER
and SVR_REV. The SVR_REV is the low 8 bits rather than the low 16
bits of svr. And we use the CONFIG_SYS_FSL_A004447_SVR_REV macro
instead of hard-code value 0x10, 0x11 and 0x20.

The CONFIG_SYS_FSL_A004447_SVR_REV = 0x00 represents that one
version of platform has this I2C errata. So enable this errata
by IS_SVR_REV(svr, maj, min) function.

Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Heiko Schocher <hs@denx.de>
2013-08-20 11:15:31 +02:00
Chunhe Lan
b8ce3343b6 fsl_i2c: generate nine pulses on SCL if the I2C bus is hung
When the code detected that the bus is hung (e.g. SDA stuck low),
send 9 pulses on SCL to try to fixup the bus.

Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Heiko Schocher <hs@denx.de>
2013-08-20 11:15:31 +02:00
Simon Glass
cdce889959 tegra: Avoid using I2C prior to relocation
Tegra recently moved to the new I2C framework, which sets up I2C prior to
relocation, and prior to calling i2c_init_board(). This causes a crash on
Tegra boards.

Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
2013-08-13 17:11:25 -04:00
Marek Vasut
90f002a90f i2c: soft: Fix typo in CONFIG_SYS_I2C_SOFT_SPEED
In case only the CONFIG_SYS_I2C_SPEED is set in configuration file,
the CONFIG_SYS_I2C_SOFT_SPEED is defined as CONFIG_SYS_I2C_SPEED.
The CONFIG_SYS_I2C_SOFT_SPEED is then used throughout the driver.

Unfortunatelly, due to a typo in the driver, instead of defining
CONFIG_SYS_I2C_SOFT_SPEED, an CONFIG_SYS_SOFT_I2C_SPEED was defined
and therefore the driver failed to compile. The same applies for
CONFIG_SYS_I2C_SOFT_SLAVE , where the swap happens as well.

This patch fixes the issue.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
2013-08-03 06:01:18 +02:00
Tom Rini
8dde4ca90e drivers/i2c: Update fti2c010.[ch], i2c_core.c to use SPDX identifiers
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-25 08:51:42 -04:00
Tom Rini
c2120fbfbc Merge branch 'master' of git://git.denx.de/u-boot-i2c
The sandburst-specific i2c drivers have been deleted, conflict was just
over the SPDX conversion.

Conflicts:
	board/sandburst/common/ppc440gx_i2c.c
	board/sandburst/common/ppc440gx_i2c.h

Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24 09:50:24 -04:00
Wolfgang Denk
1a4596601f Add GPL-2.0+ SPDX-License-Identifier to source files
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24 09:44:38 -04:00
Kuo-Jung Su
3cff842bca i2c: add Faraday FTI2C010 I2C controller support
Faraday FTI2C010 is a multi-function I2C controller
which supports both master and slave mode.
This patch simplily implements the master mode only.

Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
CC: Heiko Schocher <hs@denx.de>
2013-07-23 08:34:58 +02:00
Alison Wang
30ea41a489 I2C: mxc_i2c: Add support for Vybrid VF610 platform
This patch adds support for Vybrid VF610 platform.

There are some differences between i.MX6 and Vybrid for I2C controller.
(1) The registers' offset are different.
(2) The I2C clock divider values are different.
(3) In I2C control register, the enable/disable/reset bit is inverted for Vybrid comparing to i.MX6.
(4) In I2C status register, the interrupt flag bit is cleared by writing "1" for Vybrid.
For i.MX6, this bit is cleared by writing "0".
(5) In I2C status register, the arbitration lost flag bit is cleared by writing "1" for Vybrid.
For i.MX6, this bit is cleared by writing "0".

Signed-off-by: Alison Wang <b18965@freescale.com>
2013-07-23 08:34:57 +02:00
Dirk Eibach
880540decf i2c, ppc4xx_i2c: switch to new multibus/multiadapter support
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Cc: Heiko Schocher <hs@denx.de>
Cc: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
2013-07-23 08:34:56 +02:00
Simon Glass
1f2ba722ac tegra: i2c: Enable new CONFIG_SYS_I2C framework
This enables CONFIG_SYS_I2C on Tegra, updating existing boards and the Tegra
i2c driver to support this.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Heiko Schocher <hs@denx.de>
2013-07-23 08:34:55 +02:00
Simon Glass
d84eb856c4 tegra: i2c: Add function to know about current bus
Rather than using a variable in various places, add a single function,
tegra_i2c_get_bus(), which returns a pointer to information about a
bus.

This will make it easier to move to the new i2c framework.

Signed-off-by: Simon Glass <sjg@chromium.org>
2013-07-23 08:34:54 +02:00
Heiko Schocher
00f792e0df i2c, fsl_i2c: switch to new multibus/multiadapter support
- added to fsl_i2c driver new multibus/multiadpater support
- adapted all config files, which uses this driver

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
2013-07-23 08:34:53 +02:00
Heiko Schocher
ea818dbbcd i2c, soft-i2c: switch to new multibus/multiadapter support
- added to soft_i2c driver new multibus/multiadpater support
- adapted all config files, which uses this driver

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
2013-07-23 05:54:29 +02:00
Heiko Schocher
385c9ef5a7 i2c: add i2c_core and prepare for new multibus support
This Patch introduce the new i2c_core file, which holds
the I2C core functions, for the rework of the multibus/
multiadapter support.
Also adds changes in i2c.h for the new I2C multibus/multiadapter
support. This new support can be activated with the
CONFIG_SYS_I2C define.

Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
2013-07-23 05:54:28 +02:00
Reinhard Pfau
b778c1b5de i2c: fsl_i2c: i2c_read(): dont try to write address w/ alen=0
if alen is 0: no longer start a write cycle before reading data.

Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Reinhard Pfau <reinhard.pfau@gdsys.cc>
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-07-16 17:44:30 -05:00
Amar
1ae76d438b EXYNOS: Resolve the i2c compilation error
This patch resolves the below mentioned compilation error of i2c driver
for non-FDT case

Compilation error:
s3c24x0_i2c.c: In function 'board_i2c_init':
s3c24x0_i2c.c:544:18: error: 'CONFIG_MAX_I2C_NUM' undeclared (first use
in this function) s3c24x0_i2c.c:544:18: note: each undeclared
identifier is reported only once for each function it appears in
s3c24x0_i2c.c:545:3: warning: implicit declaration of function

Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Amar <amarendra.xt@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-07-10 14:20:26 +09:00
Amar
2c07bb9b53 EXYNOS5: I2C: Add FDT and non-FDT support for I2C
This patch updates the function board_i2c_init() to add support for both
FDT and non-FDT for I2C, and initialise the I2C channels.

Signed-off-by: Amar <amarendra.xt@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-06-24 11:25:19 +09:00
Lubomir Popov
960187ffa1 ARM: OMAP: I2C: New read, write and probe functions
New i2c_read, i2c_write and i2c_probe functions, tested on OMAP4
(4430/60/70), OMAP5 (5430) and AM335X (3359); should work on older
OMAPs and derivatives as well. The only anticipated exception would
be the OMAP2420, which shall require driver modification.
- Rewritten i2c_read to operate correctly with all types of chips
  (old function could not read consistent data from some I2C slaves).
- Optimised i2c_write.
- New i2c_probe, performs write access vs read. The old probe could
  hang the system under certain conditions (e.g. unconfigured pads).
- The read/write/probe functions try to identify unconfigured bus.
- Status functions now read irqstatus_raw as per TRM guidelines
  (except for OMAP243X and OMAP34XX).
- Driver now supports up to I2C5 (OMAP5).

Signed-off-by: Lubomir Popov <lpopov@mm-sol.com>
Tested-by: Heiko Schocher <hs@denx.de>
2013-06-10 08:43:26 -04:00
Michal Simek
8934f78465 i2c: zynq: Add support for Xilinx Zynq
Support Xilinx Zynq i2c controller.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@ti.com>
2013-04-30 11:39:28 +02:00
Tom Rini
0ce033d258 Merge branch 'master' of git://git.denx.de/u-boot-arm
Albert's rework of the linker scripts conflicted with Simon's making
everyone use __bss_end.  We also had a minor conflict over
README.scrapyard being added to in mainline and enhanced in
u-boot-arm/master with proper formatting.

Conflicts:
	arch/arm/cpu/ixp/u-boot.lds
	arch/arm/cpu/u-boot.lds
	arch/arm/lib/Makefile
	board/actux1/u-boot.lds
	board/actux2/u-boot.lds
	board/actux3/u-boot.lds
	board/dvlhost/u-boot.lds
	board/freescale/mx31ads/u-boot.lds
	doc/README.scrapyard
	include/configs/tegra-common.h

Build tested for all of ARM and run-time tested on am335x_evm.

Signed-off-by: Tom Rini <trini@ti.com>
2013-03-18 14:37:18 -04:00
Tom Warren
e32624ef82 Tegra: I2C: Add T114 clock support to tegra_i2c driver
T114 has a slightly different I2C clock, with a new (extra) divisor
in standard/fast mode and HS mode. Tested on my Dalmore, and the I2C
clock is 100KHz +/- 3Hz on my Saleae Logic analyzer.

Added a new entry in compat_names for T114 I2C since it differs
from the previous Tegra SoCs. A flag is set when T114 I2C HW is
found so new features like the extra clock divisor can be used.

Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
2013-03-14 11:06:41 -07:00
Rajeshwari Shinde
cb466c056a I2C: S3C24X0: Bug fixes in i2c_transfer
This patch corrects the following issues

1) Write the correct M/T Stop value to I2CSTAT after i2c write.
   According to the spec, after finish the data transmission, we should
   write a M/T Stop (I2C_MODE_MT | I2C_TXRX_ENA) to I2CSTAT instead of
   a M/R Stop (I2C_MODE_MR | I2C_TXRX_ENA).
2) Not split the write to I2CSTAT into 2 steps in i2c read.
   According to the spec, we should write the combined M/R Start value to
   I2CSTAT after setting the slave address to I2CDS
3) Fix the mistake of making an equality check to an assignment.
   In the case of I2C write with the zero-length address, while tranfering the
   data, it should be an equality check (==) instead of an assignment (=).

Signed-off-by: Tom Wai-Hong Tam <waihong@chromium.org>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
2013-03-12 19:33:11 +01:00
Rajeshwari Shinde
cecf3c006f I2C: S3C24X0: Remove the dead code
This revomes the code under #if 0 in the s3c24x0_i2c driver.

Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
2013-03-12 19:32:41 +01:00
Simon Glass
609e6ec3f6 ppc: m68k: Move i2c1_clk, i2c2_clk to arch_global_data
Move these fields into arch_global_data and tidy up. This is needed for
both ppc and m68k since they share the i2c driver.

Signed-off-by: Simon Glass <sjg@chromium.org>
2013-02-04 09:05:42 -05:00
Marek Vasut
49c28b564b i2c: mxs: Staticize the functions in the driver
The local functions in the mxs i2c driver are not marked static, make it so.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Heiko Schocher <hs@denx.de>
2013-01-29 06:39:52 +01:00
Albert ARIBAUD
1199c377cf Merge branch 'u-boot-samsung/master' into 'u-boot-arm/master' 2013-01-14 15:21:00 +01:00
Rajeshwari Shinde
d04df3c6ad I2C: S3C24X0: Resolve build error for VCMA9
This patch resolves the following build errors for I2C driver in
VCMA9:

In file included from s3c24x0_i2c.c:40:0:
s3c24x0_i2c.h:38:17: error: field 'id' has incomplete type
s3c24x0_i2c.c:70:39: error: 'CONFIG_MAX_I2C_NUM' undeclared here (not
in a function) s3c24x0_i2c.c:70:31: warning: 'i2c_bus' defined but
not used [-Wunused-variable] s3c24x0_i2c.c:72:12: warning:
'i2c_busses' defined but not used [-Wunused-variable]

Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-01-14 14:45:30 +09:00
Albert ARIBAUD
79f3877794 Merge branch 'u-boot-ti/master' into 'u-boot-arm/master'
This required manual merging drivers/mtd/nand/Makefile
and adding am335x_evm support for CONFIG_SPL_NAND_DRIVERS
2013-01-08 13:15:45 +01:00
Rajeshwari Shinde
a9d2ae7014 I2C: Driver changes for FDT support
Functions added to get the I2C bus number and reset I2C bus using
FDT node.

Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-01-08 10:54:33 +09:00
Armando Visconti
d40d914c06 designware_i2c.h: Define IC_CLK only if not already defined in config file
Signed-off-by: Armando Visconti <armando.visconti@st.com>
2012-12-11 13:17:32 -07:00
Armando Visconti
ea31b7a7be designware_i2c.h: Fixed the correct values for SCL low/high time
Signed-off-by: Armando Visconti <armando.visconti@st.com>
2012-12-11 13:17:32 -07:00
Armando Visconti
5b8439bbde designware_i2c: Fixed the setting of the i2c bus speed
There are three couple (hcnt/lcnt) of registers for each
speed (SS/FS/HS). The driver needs to set the proper couple
of regs according to what speed we are setting.

Signed-off-by: Armando Visconti <armando.visconti@st.com>
2012-12-11 13:17:32 -07:00
Armando Visconti
491739bb74 designware_i2c: Added s/w generation of stop bit
In the newer versions of designware i2c IP there is the possibility
of configuring it with IC_EMPTYFIFO_HOLD_MASTER_EN=1, which basically
requires the s/w to generate the stop bit condition directly, as
the h/w will not automatically generate it when TX_FIFO is empty.

To avoid generation of an extra 0x0 byte sent as data, the
IC_STOP command must be sent along with the last IC_CMD.

This patch always writes bit[9] of ic_data_cmd even in the
older versions, assuming that it is a noop there.

Signed-off-by: Armando Visconti <armando.visconti@st.com>
2012-12-11 13:17:32 -07:00
Armando Visconti
ac6e2fe6e4 designware_i2c.c: Added the support for MULTI_BUS
This patch adds the capability to switch between 10
different I2C busses (from 0 to 9).

Signed-off-by: Armando Visconti <armando.visconti@st.com>
2012-12-11 13:17:31 -07:00
Piotr Wilczek
c86d9ed382 drivers:i2c: Modify I2C driver for Exynos4
This patch modifies the S3C i2c driver to support both Exynos4 and Exynos5

Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Minkyu Kang <mk7.kang@samsung.com>
2012-12-11 13:17:31 -07:00
Vincent Stehlé
66839773a8 omap24xx_i2c: Handle OMAP5 like OMAP2,3,4
OMAP5 has 8b i2c data register field, like OMAP2, 3 and 4. Handle in the same
way. This fixes the following error on OMAP5:

  OMAP5430 EVM # mmc rescan
  timed out in wait_for_bb: I2C_STAT=1410
  twl6035: could not turn on LDO9.

Signed-off-by: Vincent Stehlé <v-stehle@ti.com>
2012-12-11 13:17:31 -07:00
Marek Vasut
fa5e2845a8 mxs: i2c: Implement algorithm to set up arbitrary i2c speed
This algorithm computes the values of TIMING{0,1,2} registers for the
MX28 I2C block. This algorithm was derived by using a scope, but the
result seems correct.

The resulting values programmed into the registers do not correlate
with the contents in datasheet. When using the values from the datasheet,
the I2C clock were completely wrong.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Wolfgang Denk <wd@denx.de>
2012-12-11 13:17:30 -07:00
Marek Vasut
1e2fc0d19b mxs: i2c: Restore speed setting after block reset
The I2C block reset configures the I2C bus speed to strange value.
Read the I2C speed from the block before reseting the block and
restore it afterwards, so the I2C operates correctly. This issue
can be replicated by doing unsuccessful I2C transfer, after such
transfer finishes, the I2C block clock speed is misconfigured.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
2012-12-11 13:17:30 -07:00
Marek Vasut
aff36ea92e i2c: mxs: Fix TIMING2 register value
According to FSL, the value in the TIMING2 register shall be 0x00300030
instead of what's written in the datasheet. This new value correlates
with older STMP36xx datasheet. Issues were detected in Linux when this
register was misconfigured, so write this correct value.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
2012-12-11 13:17:30 -07:00
Marek Vasut
a157e0d5f6 i2c: mxs: Use i2c_set_bus_speed() in i2c_init()
Use i2c_set_bus_speed() in i2c_init() within the mxs i2c driver
to avoid duplication of code.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
2012-12-11 13:17:30 -07:00
Marek Vasut
a06f590f7f i2c: mxs: Implement i2c_get/set_bus_speed()
This patch implements the setup and retrieval functions for the I2C
bus speed on the MXS I2C IP.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
2012-12-11 13:17:30 -07:00
Marek Vasut
f32a470ed3 i2c: mxs: Abstract out the MXS I2C speed setup
This patch pulls out the I2C speed setup from the i2c_init() call
and implements the bus configuration lookup table with register
values that needs to be programmed into the I2C IP to run at
particular speed.

This patch is a first step towards implementing run-time I2C bus
speed configuration for the MXS I2C IP.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
2012-12-11 13:17:30 -07:00
Marek Vasut
7f86bd576f i2c: Staticize local functions in mxc i2c driver
Some functions in the MXC i2c driver were not static, fix this by
making them so.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
2012-12-11 13:17:29 -07:00
Andreas Bießmann
eabd5d8d70 soft_i2c: add necessary includes for AVR32
Signed-off-by: Andreas Bießmann <biessmann@corscience.de>
2012-12-11 13:17:29 -07:00
Vincent Stehlé
febc4cd48a omap24xx_i2c: Handle wait_for_bb error
We add a return code to wait_for_bb() to be able to report errors to the
callers properly. We in turn handle this new error code in i2c_read, i2c_write
and i2c_probe.

Signed-off-by: Vincent Stehlé <v-stehle@ti.com>
2012-12-10 12:45:35 -07:00
Tom Rini
5bb3505fa8 Merge branch 'master' of git://git.denx.de/u-boot-arm 2012-10-26 15:44:31 -07:00
Marek Vasut
6f62f42071 arm: Remove support for lpc2292
This stuff has been rotting in the tree for a year now. Remove it.

Signed-off-by: Marek Vasut <marex@denx.de>
2012-10-26 22:35:20 +02:00
Kim Phillips
62f730fffd drivers/i2c/fsl_i2c.c: sparse fix
fsl_i2c.c:217:14: warning: symbol 'get_i2c_clock' was not declared. Should it be static?

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Acked-by: Heiko Schocher <hs@denx.de>
2012-10-25 12:06:21 -07:00
Tetsuyuki Kobayashi
f539094f48 i2c: sh_i2c: use setbits/clrbits macro
Use setbits/clrbits macro when read-modify-write register.

Signed-off-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
Acked-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2012-10-16 05:47:21 +02:00