setup_weimcs() and some macros are added to support the setup
for i.MX31 WEIM chip selects. As a compromise between verbosity
and readability an ASCII-art'ish bit comment is used instead of
bitfields.
All i.MX31 boards have been patched to use this approach using a
helper program to verify the changes.
Signed-off-by: Helmut Raiger <helmut.raiger@hale.at>
Acked-by: Stefano Babic <sbabic@denx.de>
This commit updates the mach-types based on the latest in Linus's head
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
This adds support for changing pinmux functions of pin groups. This is done
by defining a PMUX_FUNC_... enum which can be used to select the function for
each group using pinmux_set_func(). It is also possible to enable
pullup/pulldown, and the existing tristate functionality is retained.
Also provided is a means of configuring a list of pingroups by providing a
configuration table to pinmux_config_table().
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Warren <twarren@nvidia.com>
The pin groupings are better named PINGRP, since on Tegra2 they refer to
multiple pins.
Sorry about this, but better to get it right now when there is only a small
amount of code affected.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Warren <twarren@nvidia.com>
This adds most of the clock functions required by board and driver code:
-query and adjust peripheral clocks
-query and adjust PLLs
-reset and enable control
These functions are plumbed in as required.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Warren <twarren@nvidia.com>
Rename CLOCK_PLL_ID to CLOCK_ID which takes account of the fact that the
code now deals with both PLL clocks and source clocks.
This also tidied up the assert() to match the one sent upstream, and fixes
an error in the PWM id.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Warren <twarren@nvidia.com>
This adds a device tree pointer to the global data. It can be set by
board code. A later commit will add support for making a device
tree binary blob available to U-Boot for run-time configuration.
Signed-off-by: Simon Glass <sjg@chromium.org>
This additionally updates mx31/generic.c by
- replacing __REG() macro accesses with readl() and writel()
- providing macros for PDR0 and PLL bit accesses
Signed-off-by: Helmut Raiger <helmut.raiger@hale.at>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Now that none of the core checks CONFIG_NET_MULTI, there's not much point
in boards defining it. So scrub all references to it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This pushes the ugly duplicated arch ifdef lists we maintain in various
image related files out to the arch headers themselves.
Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Tested-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The current post_log_word in global data is currently split into 2x
16 bits: half for the test start, half for the test success.
Since we alredy have more than 16 POST tests defined and more could
be defined, this may result in an overflow and the post_output_backlog
would not work for the tests defined further of these 16 positions.
An additional field is added to global data so that we can now support up
to 32 (depending of architecture) tests. The post_log_word is only used
to record the start of the test and the new field post_log_res for the
test success (or failure). The post_output_backlog is for this change
also adapted.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
For post to run on ARM, 3 things are needed:
- post_log_word to be defined in gd
- a post.h include in arch/arm/lib/board.c
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Allow redirection of console output prior to console initialisation to a
temporary buffer.
To enable this functionality, the board (or arch) must define:
- CONFIG_PRE_CONSOLE_BUFFER - Enable pre-console buffer
- CONFIG_PRE_CON_BUF_ADDR - Base address of pre-console buffer
- CONFIG_PRE_CON_BUF_SZ - Size of pre-console buffer (in bytes)
The pre-console buffer will buffer the last CONFIG_PRE_CON_BUF_SZ bytes
Any earlier characters are silently dropped.
The PLL decoding algorithm didn't take into account many configuration bits.
Adjust it according to Linux kernel. Also, add PLL4 for MX53.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Jason Hui <jason.hui@linaro.org>
Tested-by: Jason Liu <Jason.hui@linaro.org>
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Ben Warren <biggerbadderben@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Turn on the watchdog WDZST bit so that watchdog timer does not count during low power modes.
Prior to applying this patch mx31pdk board got watchdog resets because when it booted in the Linux prompt
and there was no activity, the system entered into idle mode while watchdog timer was still active.
Fix this by disabling watchdog timer during idle mode.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Config VMMC voltage to 3V for MMC/SD card slot
and PBIAS settings needed for OMAP4
Fixes MMC/SD detection on boot from eMMC.
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Support for the new spl structure. Using the interface defined by Aneesh V for
OMAP4
Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
OMAP3 relied on the memory config done by X-loader or Configuration Header. This
has to be reworked for the implementation of a SPL. This patch configures RAM
bank 0 if CONFIG_SPL_BUILD is set. Settings for Micron-RAM used by devkit8000
are added to mem.h
Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The existing timing does not quite meet the minimum requirements
in the LAN9221 datasheet. The timing in this patch solves problems
noticed on some parts. The patch also combines the CS configuration
for the overo and igep0020 boards per request.
Signed-off-by: Philip Balister <philip@opensdr.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch enables ethernet support for Marvell GplugD board. Network
related commands works.
Signed-off-by: Ajay Bhargav <ajay.bhargav@einfochips.com>
This patch adds support for Fast Ethernet Controller driver for
Armada100 series.
Signed-off-by: Ajay Bhargav <ajay.bhargav@einfochips.com>
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Tuning some IO settings for better performance and power.
And consolidate all such IO settings at one place.
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
SDRAM init was not working on ES1.0 due to a programming
error. A pointer that was passed by value to a function
was set in function emif_get_device_details(), but the effect
wouldn't be seen in the calling function. The issue came
out while testing for ES1.0 because ES1.0 doesn't have any
SDRAM chips connected to CS1
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Convert all OMAP specific functions to use the common API
definitions in include/asm/gpio.h. In the process, made
few additional changes:
- Use -EINVAL consistently. -1 was used in many places.
- Removed one-liner static functions that were used only
once. Replaced the content as necessary.
- Combines implementation of functions omap_get_gpio_dataout()
and omap_get_gpio_datain(). To do so, new static function
_get_gpio_direction() was added.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
OMAP3: Add 37xx ESx revision numbers.
Signed-off-by: Michael Jones <michael.jones@matrix-vision.de>
Signed-off-by: Howard D. Gray <howard.gray@matrix-vision.de>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Read directly from OMAP_GPIO_DATAOUT to get the output state of the GPIO pin
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
commit 0edf8b5b2f breaks
building on a different directory with the O= parameter.
The patch wil fix this issue, generating always asm-offsets.h before
the other targets.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Matthias Weisser <weisserm@arcor.de>
CC: Wolfgang Denk <wd@denx.de>
AHCLKR/UART1_RTS/GP0[11] pin needs to be configured for
NOR to work on Rev.3 EVM. When GP0[11] is low,
the SD0 interface will not work, but NOR flash will.
Signed-off-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com>
Signed-off-by: Nagabhushana Netagunte <nagabhushana.netagunte@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
add support for DSP wake-up by default on DA850/OMAP-L138
during board initialization. Enable hwconfig environment and added
extra env setting through CONFIG_EXTRA_ENV_SETTINGS.
To prevent DSP from being woken up,set the environment variable as,
set hwconfig "dsp:wake=no"
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Nagabhushana Netagunte <nagabhushana.netagunte@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
