GPIO pins need to be set up on start-up. Add a driver to provide this,
configured from the device tree.
The binding is slightly different from the existing ICH6 binding, since that
is quite verbose. The new binding should be just as extensible.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Bin Meng <bmeng.cn@gmail.com>
Add a driver which sets up the pin configuration on x86 devices with an ICH6
(or later) Platform Controller Hub.
The driver is not in the pinctrl uclass due to some oddities of the way x86
devices work:
- The GPIO controller is not present in I/O space until it is set up
- This is done by writing a register in the PCH
- The PCH has a driver which itself uses PCI, another driver
- The pinctrl uclass requires that a pinctrl device be available before any
other device can be probed
It would be possible to work around the limitations by:
- Hard-coding the GPIO address rather than reading it from the PCH
- Using special x86 PCI access to set the GPIO address in the PCH
However it is not clear that this is better, since the pin configuration
driver does not actually provide normal pin configuration services - it
simply sets up all the pins statically when probed. While this remains the
case, it seems better to use a syscon uclass instead. This can be probed
whenever it is needed, without any limitations.
Also add an 'invert' property to support inverting the input.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
I didn't have a common board to enable LVDS.
So add this dcocument to help others who want to enable LVDS in their board.
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Acked-by: Simon Glass <sjg@chromium.org>
This adds PIC32 UART controller support based on driver model.
Signed-off-by: Paul Thacker <paul.thacker@microchip.com>
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
PIC32 clock module consists of multiple oscillators, PLLs, mutiplexers
and dividers capable of supplying clock to various controllers
on or off-chip.
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Add the DTS documentation for the Micrel KSZ90x1 binding.
The original document was from:
[commit 4b405efbe12de28b26289282b431323d73992381 from the Linux kernel]
This takes the original document and adds a clarification on how the skew
values are represented in the code.
References:
Micrel ksz9021rl/rn Data Sheet, Revision 1.2. Dated 2/13/2014.
http://www.micrel.com/_PDF/Ethernet/datasheets/ksz9021rl-rn_ds.pdf
Micrel ksz9031rnx Data Sheet, Revision 2.1. Dated 11/20/2014.
http://www.micrel.com/_PDF/Ethernet/datasheets/KSZ9031RNX.pdf
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add a new member 'tbiaddr' to tsec_private struct. For non-DM driver,
it is initialized as CONFIG_SYS_TBIPA_VALUE, but for DM driver, we
can get this from device tree. Update the bindings doc as well.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Adapted from the same file name in the kernel device tree bindings
documentation, to use with U-Boot.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch adds the documentation for the memory-down parameters
of the Intel FSP. To configure a board without SPD DDR DIMM but
with onboard DDR chips. The values are taken from the coreboot
header:
src/soc/intel/fsp_baytrail/chip.h
(git ID da1a70ea from 2016-01-16 as reference).
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Andrew Bradford <andrew.bradford@kodakalaris.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Replace ns16550.txt with binding files from Linux kernel. As suggested
by Stephen Warren, we should keep the directory structure, filenames,
and file content identical to the bindings in the Linux kernel.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Acked-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Adding timer init function in timer-uclass driver to create and
initialize the timer device on platforms where u-boot,dm-pre-reloc
is not used. Since there will be multiple timer devices in the
system, adding a tick-timer node in chosen node to know which
timer device to be used as tick timer in u-boot.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Some boards have an i8042 device. Enable the driver for all x86 boards, and
add a device tree node for those which may have this keyboard.
Also adjust the configuration so that i8042 is always separate from the VGA,
and rename the stdin driver accordingly. With this commit the keyboard will
not work, but it is fixed in the next commit.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a sandbox timer which get time from host os and a basic
test.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add Altera Generic Quad SPI Controller support. The controller
converts SPI NOR flash to parallel flash interface. So it is
not like other SPI flash, but rather like CFI flash.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
This commit adds:
- new uclass id: UCLASS_ADC
- new uclass driver: drivers/adc/adc-uclass.c
The new uclass's API allows for ADC operation on:
* single-channel with channel selection by a number
* multti-channel with channel selection by bit mask
ADC uclass's functions:
* single-channel:
- adc_start_channel() - start channel conversion
- adc_channel_data() - get conversion data
- adc_channel_single_shot() - start/get conversion data
* multi-channel:
- adc_start_channels() - start selected channels conversion
- adc_channels_data() - get conversion data
- adc_channels_single_shot() - start/get conversion data for channels
selected by bit mask
* general:
- adc_stop() - stop the conversion
- adc_vdd_value() - positive reference Voltage value with polarity [uV]
- adc_vss_value() - negative reference Voltage value with polarity [uV]
- adc_data_mask() - conversion data bit mask
The device tree can provide below constraints/properties:
- vdd-polarity-negative: if true: Vdd = vdd-microvolts * (-1)
- vss-polarity-negative: if true: Vss = vss-microvolts * (-1)
- vdd-supply: phandle to Vdd regulator's node
- vss-supply: phandle to Vss regulator's node
And optional, checked only if the above corresponding, doesn't exist:
- vdd-microvolts: positive reference Voltage [uV]
- vss-microvolts: negative reference Voltage [uV]
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This driver allows I/O operations on the Samsung S2MPS11 PMIC,
which provides lots of LDO/BUCK outputs.
To enable it, update defconfig with:
- CONFIG_PMIC_S2MPS11
and additional, if were not defined:
- CONFIG_CMD_PMIC
- CONFIG_ERRNO_STR
The binding info: doc/device-tree-bindings/pmic/s2mps11.txt
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The CPU name for Exynos was concatenated with cpu id,
but for new Exynos platforms, like Chromebook Peach Pi
based on Exynos5800, the name of SoC variant does not
include the real SoC cpu id (0x5422).
For such case, the CPU name should be defined in device tree.
This commit introduces new device-tree property for Exynos:
- "cpu-model" - with cpu name string
If defined, then the cpu id is not printed.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Added device-tree-binding information for zynq qspi controller
driver.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Jagan Teki <jteki@openedev.com>
Convert altera_tse to driver model and phylib.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Convert altera sysid to driver model with misc uclass.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Acked-by: Chin Liang See <clsee@altera.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Convert nios2 cpu to driver model. The cpu parameters are
extracted from device tree and saved to global data structure.
We will use them to replace the custom_fpga.h .
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Simon Glass <sjg@chromium.org>
Convert altera_pio to driver model.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Acked-by: Chin Liang See <clsee@altera.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Convert altera_uart to driver model.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Marek Vasut <marex@denx.de>
Convert altera_jtag_uart to driver model.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Many System on Chip(SoC) solutions are complex with multiple processors
on the same die dedicated to either general purpose of specialized
functions. Many examples do exist in today's SoCs from various vendors.
Typical examples are micro controllers such as an ARM M3/M0 doing a
offload of specific function such as event integration or power
management or controlling camera etc.
Traditionally, the responsibility of loading up such a processor with a
firmware and communication has been with a High Level Operating
System(HLOS) such as Linux. However, there exists classes of products
where Linux would need to expect services from such a processor or the
delay of Linux and operating system being able to load up such a
firmware is unacceptable.
To address these needs, we need some minimal capability to load such a
system and ensure it is started prior to an Operating System(Linux or
any other) is started up.
NOTE: This is NOT meant to be a solve-all solution, instead, it tries to
address certain class of SoCs and products that need such a solution.
A very simple model is introduced here as part of the initial support
that supports microcontrollers with internal memory (no MMU, no
execution from external memory, or specific image format needs). This
basic framework can then (hopefully) be extensible to other complex SoC
processor support as need be.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Simon Glass <sjg@chromium.org>
Bring in required device tree files from Linux. Since mainline Linux is
somewhat behind, use the files from the Chromium tree. We can re-sync once
further code is acccepted upstream.
Signed-off-by: Simon Glass <sjg@chromium.org>
Allow for configuration of FSP UPD from the device tree which will
override any settings which the FSP was built with itself.
Modify the MinnowMax and BayleyBay boards to transfer sensible UPD
settings from the Intel FSPv4 Gold release to the respective dts files,
with the condition that the memory-down parameters for MinnowMax are
also used.
Signed-off-by: Andrew Bradford <andrew.bradford@kodakalaris.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Removed fsp,mrc-debug-msg and fsp,enable-xhci for minnowmax, bayleybay
Fixed lines >80col
Signed-off-by: Simon Glass <sjg@chromium.org>
We do not need that "regulator-name" property must be provided in dts.
If "regulator-name" property is not provided in dts, node name
will chosen for settings '.name' field of uc_pdata.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
This chip provides an eDP to LVDS bridge which is useful for SoCs that don't
support LVDS displays (or it would waste scarce pins). The setup is included
in the device tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a new I2C_MUX uclass. Devices in this class can multiplex between
several I2C buses, selecting them one at a time for use by the system.
The multiplexing mechanism is left to the driver to decide - it may be
controlled by GPIOs, for example.
The uclass supports only two methods: select() and deselect().
The current mux state is expected to be stored in the mux itself since
it is the only thing that knows how to make things work. The mux can
record the current state and then avoid switching unless it is necessary.
So select() can be skipped if the mux is already in the correct state.
Also deselect() can be made a nop if required.
Signed-off-by: Simon Glass <sjg@chromium.org>
Zynq is using Cadence IP where binding is documented in the Linux kernel
and there is no reason to use different binding.
Synchronize it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add a simple uclass for LEDs, so that these can be controlled by the device
tree and activated when needed. LEDs are referred to by their label.
This implementation requires a driver for each type of LED (e.g GPIO, I2C).
Signed-off-by: Simon Glass <sjg@chromium.org>
This patch adds the device tree binding doc for the cadence qspi controller &
also removes the not needed properties from the stv0991 device tree.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
Now zynq spi driver platform data is controlled by devicetree,
enable the status by saying "okay" on respective board dts to use
the devicetree generated platdata.
Ex:
&spi1 {
status = "okay";
};
Signed-off-by: Jagan Teki <jteki@openedev.com>
Acked-by: Simon Glass <sjg@chromium.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Tested-by: Jagan Teki <jteki@openedev.com>
Before device-tree, the device serial number used to be passed to the kernel
using ATAGs (on ARM). This is now deprecated and all the handover to the kernel
should now be done using device-tree. Thus, this passes the serial-number
property to the kernel using the serial-number property of the root node, as
expected by the kernel.
The serial number is a string that somewhat represents the device's serial
number. It might come from some form of storage (e.g. an eeprom) and be
programmed at factory-time by the manufacturer or come from identification
bits available in e.g. the SoC.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Simon Glass <sgj@chromium.org>
Every pin can be configured now from the device tree. A dt-bindings
has been added to describe the different property available.
Change-Id: I1668886062655f83700d0e7bbbe3ad09b19ee975
Signed-off-by: Gabriel Huau <contact@huau-gabriel.fr>
Acked-by: Simon Glass <sjg@chromium.org>
Describe all required properties needed by the irq router device tree.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
This commit adds emulation of sandbox PMIC device, which includes:
- PMIC I2C emulation driver
- PMIC I/O driver (UCLASS_PMIC)
- PMIC regulator driver (UCLASS_REGULATOR)
The sandbox PMIC has 12 significant registers and 4 as padding to 16 bytes,
which allows using 'i2c md' command with the default count (16).
The sandbox PMIC provides regulators:
- 2x BUCK
- 2x LDO
Each, with adjustable output:
- Enable state
- Voltage
- Current limit (LDO1/BUCK1 only)
- Operation mode (different for BUCK and LDO)
Each attribute has it's own register, beside the enable state, which depends
on operation mode.
The header file: sandbox_pmic.h includes PMIC's default register values,
which are set on i2c pmic emul driver's probe() method.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested on sandbox:
Tested-by: Simon Glass <sjg@chromium.org>
