Sometimes we need know if a given hub device is root hub or not.
Add a new API to test this. This removes the xHCI driver's own
version is_root_hub() and change to use the new API.
While we are here, remove the unused/commented out get_usb_device()
in the xHCI driver too.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
At present hub_port_reset() is defined in DM USB, but it is never
called hence remove it (removing another ifdefs).
While we are here, change legacy_hub_port_reset() name to
usb_hub_port_reset() to better match other function names in the
same hub module.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Occasionally it was observed that on Intel MinnowMax board, with a
USB 2.0 device connected to the bottom port, when doing 'usb start'
on the xHCI controller:
scanning bus 0 for devices... cannot reset port 3!?
But neither of the two USB ports is routed to xHCI root port 3.
Adding some debug information shows that xHCI port 3 PORTSC register
mysteriously reports both CCS = 1 and CSC = 1.
This is not seen every time. After increasing the timeout to wait
for power to become stable, the issue is gone. So this indicates
current default USB power-on delay (20ms) might be at a critical
region where power is stable/unstable. U-Boot provides a mechanism
to have a environment variable to override the default one. Add
one for MinnowMax.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Now that EHCD does not use CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS,
remove it in all boards' config files.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Now that xHCD does not use CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS,
remove it in all boards' config files.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
USB 3.0 hub port status has different bit position regarding to
port power, port speed, etc. But others are the same as 2.0 hubs.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
USB 3.0 hubs have a slightly different hub descriptor than USB 2.0
hubs, with a fixed (rather than variable length) size. Change the
host controller drivers that access those last two fields
(DeviceRemovable and PortPowerCtrlMask) to use the union.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Testing a USB 3.0 hub by connecting it to the xHCI port on Intel
MinnowMax, when issuing 'get hub descriptor' to the hub, xHCI
reports a transfer event TRB with a completion code 6 which means
'Stall Error'.
In fact super speed USB hub descriptor type is 0x2a, not 0x29.
Sending correct SETUP packet to the hub makes it not stall anymore.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
This function is usefull to get phandle number contained
in a property list.
For example, this allows to allocate the right amount
of memory to keep clock's reference contained into the
"clocks" property.
To implement it, either of_count_phandle_with_args() or
fdtdec_parse_phandle_with_args() are used respectively
for live tree and flat tree.
By passing index = -1, these 2 functions returns the
number of phandle contained into the property list.
Add also the dev_count_phandle_with_args() based on
ofnode_count_phandle_with_args()
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add clk_release_all() method which Disable/Free an
array of clocks that has been previously requested by
clk_request/get_by_*()
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add reset_release_all() method which Assert/Free an
array of resets signal that has been previously successfully
requested by reset_get_by_*()
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This is needed in error path to assert previously deasserted
reset by using a saved reset_ctl reference.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This allow to check if a PHY has been correctly
initialised and avoid to get access to phy struct.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Some platforms have very limited SRAM to run SPL code, so there may
not be the same amount space for a malloc pool before relocation in
the SPL stage as the normal U-Boot stage.
Make SPL and (the full) U-Boot stage use independent SYS_MALLOC_F_LEN,
so the size of pre-relocation malloc pool can be configured memory
space independently.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[fixed up commit-message:]
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add "preboot=usb start" to ROCKCHIP_DEVICE_SETTINGS,you don't
need to input "usb start" in command line of u-boot console,it
can auto-start the USB device,after that usb keyboard can work.
Signed-off-by: Leo Wen <leo.wen@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add the 'usbkbd' environment variable to the 'stdin', the contents of
the keyboard input can be auto-displayed on the serial terminal,so
you don't need to manually set the environment variable 'stdin'.
Signed-off-by: Leo Wen <leo.wen@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
SPL_SERIAL_SUPPORT and SPL_DRIVERS_MISC_SUPPORT were previously
enabled through rk3399_common.h. This change implies these options
through Kconfig.
These need to always be active for the RK3399, as follows:
- SPL_SERIAL_SUPPORT is needed to pass the SPL build
- SPL_DRIVERS_MISC_SUPPORT is needed to pass the SPL build
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
We use to use /dev/mmcbl0p7 as root partition, and pass it
to kernel by cmdline, but the mmc number in kernel in not
fixed, we need to change the bootargs to adapt it from time
to time.
We can use the UUID to fix it, the ID is from:
https://www.freedesktop.org/wiki/Specifications/DiscoverablePartitionsSpec/
ARM 32bit: 69dad710-2ce4-4e3c-b16c-21a1d49abed3
ARM 64bit: b921b045-1df0-41c3-af44-4c6f280d3fae
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This allow to remove include/dm/platform_data/serial_stm32x7.h
which was included in the past by stm32x7 driver and by
stm32f746-disco.c board file.
Since patch 42bf5e7c27 "serial: stm32f7: add device tree support"
this file is no more needed in board file.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Vikas MANOCHA <vikas.manocha@st.com>
Use the same clocks macro than the one used by kernel DT.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Vikas MANOCHA <vikas.manocha@st.com>
The load address of ramdisk, rdaddr is 0x88080000 and fit_loadaddr
is defined as 0x88000000. This leaves only 512Kbytes for the
fit image. When the FIT images are larger than this, it will
overwite the ramdisk and cause the boot to fail.
For eg, The K2 HS fit images are a few MB and end up overwriting
the ramdsk. This patch moves the fit_loadaddr to 0x87000000,
leaving a 16MB window for the fit image. This memory can be
reclaimed once the kernel starts running.
Signed-off-by: Madan Srinivas <madans@ti.com>
We first split the CONFIG_BOOTCOMMAND into its components to improve
readability. We then make the following order changes:
- Run findfdt first so the fdt name can be used in envboot like OMAP
- Install the boot monitor before running the PMMC so we can make any
needed secure changes before PMMC, do this on both HS and non-HS
- Move set_name_pmmc to just before get_pmmc_${boot}
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Updates the default u-boot environment variables to support secure
boot. On secure devices, a secure boot monitor (sec-bm) needs to
be installed by u-boot.
Signed-off-by: Madan Srinivas <madans@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Updates the default u-boot environment variables to support FIT image
loading.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Import Amlogic Meson DTS files from Linux kernel version 4.12
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
It has been a while since ARM Trusted Firmware supported UniPhier SoC
family. U-Boot SPL was intended as a temporary loader that runs in
secure world. It is a maintenance headache to support two different
boot mechanisms. Secure firmware is realm of ARM Trusted Firmware
and now U-Boot only serves as a non-secure boot loader for UniPhier
ARMv8 SoCs.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This converts the following to Kconfig:
CONFIG_ENV_IS_IN_MMC
CONFIG_ENV_IS_IN_NAND
CONFIG_ENV_IS_IN_UBI
CONFIG_ENV_IS_NOWHERE
In fact this already exists for sunxi as a 'choice' config. However not
all the choices are available in Kconfig yet so we cannot use that. It
would lead to more than one option being set.
In addition, one purpose of this series is to allow the environment to be
stored in more than one place. So the existing choice is converted to a
normal config allowing each option to be set independently.
There are not many opportunities for Kconfig updates to reduce the size of
this patch. This was tested with
./tools/moveconfig.py -i CONFIG_ENV_IS_IN_MMC
And then manual updates. This is because for CHAIN_OF_TRUST boards they
can only have ENV_IS_NOWHERE set, so we enforce that via Kconfig logic
now.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
The above CONFIG options are in Kconfig, and now have correct depends and
inter-dependencies. Migrate these to configs/ from include/configs/. In the
case of CMD_UBIFS also change it to be a default y if CMD_UBI.
Signed-off-by: Tom Rini <trini@konsulko.com>
With PowerPC 4xx support removed, we have removed xilinx-ppc support as
well, remove this file now.
Fixes 98f705c9ce ("powerpc: remove 4xx support")
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Pasting longer lines into the U-Boot console prompt sometimes leads to
characters missing. One problem here is the small 16-byte FIFO of the
legacy NS16550 UART, e.g. on x86 platforms.
This patch now introduces a Kconfig option to enable RX interrupt
buffer support for NS16550 style UARTs. With this option enabled, I was
able paste really long lines into the U-Boot console, without any
characters missing.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
[trini: Guard ns16550_serial_remove with
CONFIG_IS_ENABLED(SERIAL_PRESENT) to match struct assignment]
Signed-off-by: Tom Rini <trini@konsulko.com>
commit 2eb48ff7a2 ("powerpc, 8260: remove support for mpc8260")
removed support for 8260 CPU.
This patch remove some remainders.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
reginfo command is calling mpc8xx_reginfo(), mpc85xx_reginfo()
or mpc86xx_reginfo() based on CONFIG_ symbol.
As those 3 functions can't me defined at the same time, let's
rename them print_reginfo() to avoid the #ifdefs
The name is kept generic as it is not at all dependent on
powerpc arch and any other arch could want to also print
such information.
In addition, as the Makefile compiles cmd/reginfo.c only when
CONFIG_CMD_REGINFO is set, there is no need to enclose the U_BOOT_CMD
definition inside a #ifdef CONFIG_CMD_REGINFO
Lets all remove the #ifdefs around the U_BOOT_CMD as this
file is only compiled when CONFIG_CMD_REGINFO is defined
Finally, this is a PowerPC-only command, disable it on a number of
non-PowerPC platforms.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Tom Rini <trini@konsulko.com>
The Odroid C2 has two GiB of memory with two reserved regions.
reg = <0x0 0x0 0x0 0x1000000>;
reg = <0x0 0x10000000 0x0 0x200000>;
Patch
bfcef28ae4 (arm: add initial support for Amlogic Meson and
ODROID-C2) provided function dram_init_banksize to reserve the
first 16 MiB of RAM for firmware in function dram_init_banksize
in arch/arm/mach-meson/board.c and defined
CONFIG_NR_DRAM_BANKS = 1.
With this patch dram_init_banksize is changed to additionally
reserve the 2MiB region for the ARM Trusted Firmware (BL31).
CONFIG_NR_DRAM_BANKS is set to 2.
Cc: Andreas Färber <afaerber@suse.de>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
All current environments that implement redundancy use almost
identical implementations. This patch implements the env_nand
implementation as a function in env_common, and updates the
env_export function to export an env_nand-style 'flags' field by
default.
Signed-off-by: Fiach Antaw <fiach.antaw@uqconnect.edu.au>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move CONFIG_CMD_SATA option to Kconfig to fix the following build
error:
In file included from include/configs/mx6cuboxi.h:137:0,
from include/config.h:7,
from include/common.h:21,
from common/env_common.c:11:
include/config_distro_bootcmd.h:161:2: error: expected '}' before 'BOOT_TARGET_DEVICES_references_SATA_without_CONFIG_SATA'
BOOT_TARGET_DEVICES_references_SATA_without_CONFIG_SATA
Reported-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Replace fdtaddr and rdaddr variable names with u-boot standard names
fdt_addr_r and ramdisk_addr_r.
This will make the use of pxe boot more easy.
Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
Add support for Falcon mode and explain in the README the steps to
boot the kernel directly without loading the full U-Boot.
Signed-off-by: Diego Dorta <diego.dorta@nxp.com>
Acked-by: Fabio Estevam <fabio.estevam@nxp.com>
