Introduce two new weak functions, arch_spl_mmc_get_uboot_raw_sector() and
board_spl_mmc_get_uboot_raw_sector(), each of which can be overridden at
a matching level, that is arch/ and board/ , in addition to the existing
weak function spl_mmc_get_uboot_raw_sector().
This way, architecture code can define a default architecture specific
implementation of arch_spl_mmc_get_uboot_raw_sector(), while the board
code can override that using board_spl_mmc_get_uboot_raw_sector() which
takes precedence over the architecture code. In some sort of unlikely
special case where code has to take precedence over board code too, the
spl_mmc_get_uboot_raw_sector() is still left out to be a weak function,
but it should be unlikely that this is ever needed to be overridden.
Signed-off-by: Marek Vasut <marex@denx.de>
The Renesas RZ/G2L SMARC Evaluation Board Kit consists of the RZ/G2L
System-on-Module (SOM) based on the R9A07G044L2 SoC, and a common SMARC
carrier board.
The ARM TrustedFirmware code for the Renesas RZ/G2L SoC family passes a
devicetree blob to the bootloader as an argument in the same was
previous R-Car gen3/gen4 SoCs. This blob contains a compatible string
which can be used to identify the particular SoC we are running on and
this is used to select the appropriate device tree to load.
The configuration renesas_rzg2l_smarc_defconfig is added to support
building for this target. In the future this defconfig will be extended
to support other SoCs and evaluation boards from the RZ/G2L family.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The current imx8mp-dhcom-som.dtsi describes production rev.200 SoM,
add DT overlay which reinstates rev.100 SoM description to permit
prototype rev.100 SoMs to be used until they get phased out.
Signed-off-by: Marek Vasut <marex@denx.de>
Add DT overlays to support additional DH i.MX8MP DHCOM SoM 660-100
population options with 1x or 2x RMII PHY mounted on PDK2 or PDK3
carrier boards.
Use SPL DTO support to apply matching SoM specific DTO to cater
for the SoM differences. Remove ad-hoc patching of control DT from
fdtdec_board_setup().
Signed-off-by: Marek Vasut <marex@denx.de>
- Generally we just drop the #ifdef CONFIG_SYS_LONGHELP and endif lines
and use U_BOOT_LONGHELP to declare the same variable name as before
- In a few places, either rename the variable to follow convention or
introduce the variable as it was being done inline before.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
If the data version field of the EEPROM is not supported, provide a hexdump
of the data.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The different implementations of the mac command have board or vendor
specific sub-commands.
Add the command definition specific to the VisionFive 2 board.
Don't call cmd_usage() directly but return CMD_RET_USAGE instead.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The different implementations of the mac command have board or vendor
specific sub-commands.
Add the command definition specific to the SiFive HiFive Unmatched board.
Don't call cmd_usage() directly but return CMD_RET_USAGE instead.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
CONFIG_SYS_LONGHELP=n we want to reduce the size of the U-Boot binary.
The long text should be reduced to and empty string in this case.
There is not need to call cmd_usage() directly. It is sufficient to
return CMD_RET_USAGE.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Board specific implementations of the 'mac' command differ concerning the
supported sub-commands.
Move the Freescale specific mac command definition to the board code.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Handle 2GBit memory size value "2" from tlv eeprom on ddr
initialisation, to support SoMs with 512MB ddr memory.
Signed-off-by: Josua Mayer <josua@solid-run.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Extend the existing tlv vendor extension used for ram size by one byte to
also store the number of ddr channels.
The length of the tlv entry can indicate whether the new information is
present. If not default to single channel.
Signed-off-by: Josua Mayer <josua@solid-run.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Starting with PCB revision 3 we can safely make use of higher RAM
frequency again. Make use of the EEPROM detection to determine the
revision and use the updated RAM timings for new SoMs.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Yannic Moog <y.moog@phytec.de>
Tested-by: Yannic Moog <y.moog@phytec.de>
Add EEPROM detection initialisation for phyCORE-i.MX8MM and
print SoM information during boot when successful.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Yannic Moog <y.moog@phytec.de>
Tested-by: Yannic Moog <y.moog@phytec.de>
Add helper function to read out the PCB revision of a PHYTEC SoM.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Yannic Moog <y.moog@phytec.de>
Tested-by: Yannic Moog <y.moog@phytec.de>
Due to PCB layout constraints in PCB revisions until including 1549.2,
a RAM frequency of 2 GHz can cause rare instabilities. Set the RAM
frequency to 1.5 GHz to achieve a stable system under all conditions.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Yannic Moog <y.moog@phytec.de>
Tested-by: Yannic Moog <y.moog@phytec.de>
Add imx8m specific detection part. Which includes checking the
EEPROM data for article number options.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Yannic Moog <y.moog@phytec.de>
Tested-by: Yannic Moog <y.moog@phytec.de>
Recent shipped PHYTEC SoMs come with an i2c EEPROM containing
information about the hardware such as board revision and variant.
This can be used for RAM detection and loading device tree overlays
during kernel start.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Yannic Moog <y.moog@phytec.de>
Tested-by: Yannic Moog <y.moog@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
ZyXEL NSA325 specifications:
Marvell Kirkwood 88F6282 SoC
1.6 GHz CPU
1x GBE LAN port (Marvell MV88E1318)
512 MB RAM
128 MB Eon NAND, SLC
I2C
1x USB 3.0 (on PCIe bus)
2x USB 2.0
2x SATA (hot swap slots)
Serial console
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The 2nd HD is not enabled in U-Boot on the D-Link DNS325. This patch
sets the responsible GPIO to high, enabling the drive.
Suggested-by: Peter Granilla
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Tony Dinh <mibodhi@gmail.com>
When using a list of writeable variables, the initial values come
from the built-in default environment since commit 5ab8105836 ("env:
Complete generic support for writable list").
Remove unnecessary misuse of CONFIG_ENV_IS_NOWHERE as default environment.
Based on the fix done by commit b16fd7f75f ("imx6q: acc: Remove misuse
of env is nowhere driver").
Signed-off-by: Eduard Strehlau <eduard@lionizers.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Add detection of eMMC vs NAND devices on the Colibri iMX7
board. A GPIO is configured to detect the presence of an on-board resistor
that is configured differently based on the flash memory used. Depending on
the detection result, the 'variant' environment variable is set to '-emmc'
or cleared, indicating the type of storage device.
This enhancement improves variant detection during system initialization
through USB recovery mode, where U-Boot is loaded directly to RAM. This
allows variant detection for an accurate device tree selection.
Signed-off-by: Hiago De Franco <hiago.franco@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Update lpddr4 configuration and training using updated spreadsheet and
tools from NXP using data from previous spreadsheet and verified
toward datasheet:
- MX8M_Mini_LPDDR4_RPA_v22.xlsx
- mscale_ddr_tool_v3.31_setup.exe
The most relevant update is related to errata ERR050805:
"DRAM: Controller automatic derating logic may not work when
the LPDDR4 memory temperature is above 85 °C at initialization"
Other relevant fixes:
- DRAMTMG7 register: corrected calculation of T_CKPDX parameter
(equal to tCKCKEH for LPDDR4)
- RANKCTL register: corrected calculations for ODTLon and ODTLoff
to follow the JEDEC specification
- ADDRMAP7 register: added support for 17-row devices
As per errata ERR050805:
An issue exists with the automatic derating logic of the DDR
controller that only samples the LPDDR4 MR4 register when the
Temperature Update Flag (TUF) field (MR4[7] ) is 1’b1. If the
LPDDR4 memory is initialized and starts operation above 85 °C
(MR4[2:0] > 3’b011), the MR4 Temperature Update Flag (TUF) will
not be set. The DDR Controller will therefore not automatically
adjust the memory refresh rate or de-rate memory timings based
on the LPDDR4 memory temperature. This may cause the controller
incorrectly setting the refresh period, potentially cause the
LPDDR4 memory losing data contents and lead to possible data
integrity issues above 85 °C.
Errata provides three possible workaround options, while option 2
is the most reasonable:
Disable the automatic derating logic of the DDR controller and
apply fixed x2 refresh rate (0.5x refresh). This option is
suitable for designs that are expected to boot at or above 85 °C
and memory’s MR4[2:0] (Refresh Rate) DOES NOT report the following
conditions:
3b101: 0.25x refresh, no de-rating
3b110: 0.25x refresh, with de-rating
3b111: SDRAM High temperature operating limit exceeded
[1]: https://www.nxp.com/docs/en/errata/IMX8MM_0N87W.pdf
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Update the imx8mp-venice-gw74xx for revB:
- add CAN1
- add TIS-TPM on SPI2
- add FAN controller
- fix PMIC I2C bus (revA PMIC I2C was non-functional so no need for
backward compatible option)
- M2 socket GPIO's moved
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
clk:
- remove additional compatible strings for Versal NET
net:
- zynq_gem: Fix clock calculation for MDC for higher frequencies
pinctrl:
- core: Extend pinmux status buffere size
- zynqmp driver: Show also tristate configuration
test:
- add test case for pxe get
Xilinx:
- describe SelectMAP boot mode
Zynq:
- Fix nand description in DT
ZynqMP:
- DTS sync patches with kernel and also W=1 related fixes
- Add support for KD240, zcu670, e-a2197 with x-prc cards, SC revB/C with i2c
description for other SC based boards
- k24 psu_init cleanup
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCZSjvwAAKCRDKSWXLKUoM
IR34AJ92oum3pJXKxKREEZh0dCfDvJlE/wCggyzxI2T5liJfRG5jzlUuDjiLLU0=
=u1bz
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2024.01-rc1-v3' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2024.01-rc1 v3
clk:
- remove additional compatible strings for Versal NET
net:
- zynq_gem: Fix clock calculation for MDC for higher frequencies
pinctrl:
- core: Extend pinmux status buffere size
- zynqmp driver: Show also tristate configuration
test:
- add test case for pxe get
Xilinx:
- describe SelectMAP boot mode
Zynq:
- Fix nand description in DT
ZynqMP:
- DTS sync patches with kernel and also W=1 related fixes
- Add support for KD240, zcu670, e-a2197 with x-prc cards, SC revB/C with i2c
description for other SC based boards
- k24 psu_init cleanup
Update the MAINTAINERS file and propose a new MAINTAINER for j721s2 due
to the previous MAINTAINER not being associated with TI.
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Switch to using bootstd. Note with this change, we will stop using
distro_bootcmd and instead depend entirely on bootflow method of
starting the system up.
Drop header files that are no longer needed in am64x_evm.h.
k3_dfu.h is available via k3_dfu.env in am64x.env.
Drop unused macro CFG_SYS_SDRAM_BASE1.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
ti_mmc is not a valid boot_target for standard boot flow so
remove it. Prefer mmc1 (sd-card) over mmc0 (emmc).
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
This caused the wrong fdtfile to be set and was failing to apply M.2
settings.
Fixes: badaa1f6a7 ("boards: siemens: iot2050: Unify PG1 and PG2/M.2 configurations again")
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Added new xenguest_arm64_virtio_defconfig which
enables support for virtio-blk using various types
of transport like virtio-pci, vrtio-mmio. Currently
supported: up to 2 PCI host bridges and 10 MMIO devices.
Note: DT parsing code was partly taken from pci-uclass.c
Limitation: All memory regions should be
below 4GB address space.
Signed-off-by: Andrii Chepurnyi <andrii_chepurnyi@epam.com>
Current gd->ram_size and gd->ram_top reflect only the
first DRAM bank even if the SynQuacer Developerbox could
have up to three DRAM banks.
With the commit 06d514d77c ("lmb: consider EFI memory map"),
the first DRAM bank indicates <4GB address, so whole >4GB memory
is marked as EFI_BOOT_SERVICES_DATA and it results that
U-Boot can not access >4GB memory.
Since 64-bits DRAM address is fully available on the SynQuacer
Developerbox, let's set the installed DIMM information to
gd->ram_top and gd->ram_size.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>
Populate the device tree with the MC reserved memory regions.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Populate the device tree with the MC reserved memory regions.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add support for declaring in device tree the reserved memory ranges
required for MC. Since the MC firmware acts as any DMA master present
in the SoC, the reserved memory ranges need also be identity mapped
in the SMMU, so create the required 'iommu-addresses' property in
the reserved memory nodes.
For now this support is used only on LX2160A SoCs.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
PPA was a secure firmware developed in-house which is no longer
supported and replaced by TF-A quite some years ago. Drop support
for it.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
String "/soc/fman/ethernet@e8000" is 25 bytes long
and not 24 due to extra byte for null character at
the end.
Signed-off-by: Francois Berder <fberder@outlook.fr>
- None of the callers perform error checking and based on the non-empty
versions of this function, there's no checking to be done, so make
this a void.
- Add a default weak version of the function.
- Remove the empty versions of exynos_init now that we have a weak
version.
Signed-off-by: Tom Rini <trini@konsulko.com>
As part of reviewing a new platform, Daniel Schwierzeck noted that we
can have an empty Makefile in the board directory and don't need an
empty board.c file as well. Further with further cleanup in the
Makefile we can now omit the Makefile entirely. Remove a number of now
unnecessary board.c and Makefiles.
Signed-off-by: Tom Rini <trini@konsulko.com>
The SelectMAP configuration interface provides an 8-bit,
16-bit or 32-bit bidirectional data bus interface to the Versal FPGA
configuration logic that can be used for both configuration and readback.
A connected microcontoller to the SelectMAP interface can load boot
image with bitstream, TF-A (ARM Trusted Firmware) and U-Boot.
This commit adds the missing identification of the SelectMAP mode.
Signed-off-by: Polak, Leszek <LPolak@arri.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Michal Simek <michal.simek@amd.com>
Cc: Stefan Roese <sr@denx.de>
Link: https://lore.kernel.org/r/DU0PR07MB8419F7765892CDBCE7D559C5C8CFA@DU0PR07MB8419.eurprd07.prod.outlook.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add Bananapi R2 Pro board.
tested:
- sdcard
- both front usb-ports
- sata
- wan-port
lan-ports are connected to mt7531 switch where driver needs to be
separated from mtk ethernet-driver.
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Jonas Karlman <jonas@kwiboo.se>
Add a minimal generic RK3566/RK3568 board that only have eMMC and SDMMC
enabled. This defconfig can be used to boot from eMMC or SD-card on most
RK3566/RK3568 boards that follow reference board design.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
+ ae350: modify memory layout and target name
+ ae350: use generic RISC-V timer driver in S-mode
+ Support bootstage report for RISC-V
+ Support C extension exception command for RISC-V
+ Add Starfive timer support
_ alignment with kernel DT v6.5 for stm32f429 and stm32f746
_ rework way of displaying ST logo for stm32f746-disco and stm32f769-disco
STM32 MPU:
_ alignment with kernel DT v6.6-rc1
_ add RNG support for stm32mp13
_ add USB, USB boot and stm32prog command support for stm32mp13
_ add support of USART1 clock for stm32mp1
_ only print RAM and board code with SPL_DISPLAY_PRINT flag for
stm32mp1
_ rename update_sf to dh_update_sd_to_sf and add dh_update_sd_to_emmc
for stm32mp15xx DHCOR
-----BEGIN PGP SIGNATURE-----
iQJQBAABCgA6FiEEXyrViUccKBz9c35Jysd4L3sz/6YFAmUdaJccHHBhdHJpY2Uu
Y2hvdGFyZEBmb3NzLnN0LmNvbQAKCRDKx3gvezP/ptHxEACdibF5EoRb40qhQCWB
mwW50s76xWOyHGOGjSe3l18zxPdBjQ+9rnT8/A+mjaa8he4kMX9EZJyYRogcz7eR
QcnSeu9Q4L8bKbqnPBOpKF6TN7rFOIUcu+BWp3o8jZ+7/q7OSJrVLsjbXtCuCLnB
q5Pie/in7hmHJsQr6LJ4r31chW6Zm4VDuFiXquuxyE/c94Q8Ue27ag1/RfXL8b/g
Ir9aO+PAldGnVdnhPz4e6PZhzMfCVafw+DR7GVx3Zfnx2bg/dajo38UaLBDdEIS1
EIKONU2CBT/W1kPkLFiz+NdaYCzK9EL+RIbN/iG7ms+ds1+wc3zXpWwqZFASfIod
ZF788Up+wW+3SrKI2ySFjhQroNzDascn+bbHm4yJuAsORqY0XkxjSuWcSz++q8Hs
eMTw/R4uMfEiDvN1A7xlhBMuBrBHk4/6bdCRx2R6nkWes542fsgjXy8tGRWyUgnY
nbpTfYU07N8ck6arZ36KThedD7whJHHRcBYtLjhRG+lKbD0epWy67pXgTr9edTLf
U6ddH+Tndn4qhx067VhZ8vEXTCzypt4lY61MLcM0b9z8S1nJDn8b8jmiii7IR76L
/ocXzuLvNWHfmwNnB2hj/YY+n78vlZhegUxL5/6sH9lNebnewyEzCkVENNELUSYf
8M6vEZprvuhN44Z6hBUWZxXk0w==
=1mUx
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20231004' of https://source.denx.de/u-boot/custodians/u-boot-stm
STM32 MCU:
_ alignment with kernel DT v6.5 for stm32f429 and stm32f746
_ rework way of displaying ST logo for stm32f746-disco and stm32f769-disco
STM32 MPU:
_ alignment with kernel DT v6.6-rc1
_ add RNG support for stm32mp13
_ add USB, USB boot and stm32prog command support for stm32mp13
_ add support of USART1 clock for stm32mp1
_ only print RAM and board code with SPL_DISPLAY_PRINT flag for
stm32mp1
_ rename update_sf to dh_update_sd_to_sf and add dh_update_sd_to_emmc
for stm32mp15xx DHCOR
[ Fix merge conflict at board/st/common/stm32mp_dfu.c ]
Signed-off-by: Tom Rini <trini@konsulko.com>
