Commit graph

20329 commits

Author SHA1 Message Date
Vivek Gautam
0bf796f7ae usb: hub: Parallelize power-cycling of root-hub ports
Untill now we power-cycle (aka: disable power on a port
and re-enabling again) one port at a time.
Delay of 20ms for Port-power to change multiplies with
number of ports in this case.
So better we parallelize this process:
disable power on all ports, wait for port-power to stabilize
and then re-enable the power subsequently.

Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
2013-05-06 02:16:36 +02:00
Bo Shen
158947d276 USB: ohci-at91: make OHCI work on at91sam9g10 SoC
The at91sam9g10 need to configure HCK0 to make OHCI work

Signed-off-by: Bo Shen <voice.shen@atmel.com>
2013-05-05 23:54:22 +02:00
Vivek Gautam
6497c66704 USB: SS: Add support for Super Speed USB interface
This adds usb framework support for super-speed usb, which will
further facilitate to add stack support for xHCI.

Signed-off-by: Vikas C Sajjan <vikas.sajjan@samsung.com>
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
2013-05-05 23:54:22 +02:00
Vivek Gautam
289f3cb28a usb: hub: Fix enumration timeout
Patch b6d7852c increases timeout for enumeration, taking
worst case to be 10 sec.
get_timer() api returns timestamp in milliseconds, which is
what we are checking in the do-while() loop in usb_hub_configure()
(get_timer(start) < CONFIG_SYS_HZ * 10).
This should give us a required check for 10 seconds, and thereby
we don't need to add additional mdelay of 100 microseconds in
each cycle.

Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Reviewed-by: Vipin Kumar <vipin.kumar@st.com>
2013-05-05 23:54:22 +02:00
Vivek Gautam
99c3491b78 usb: Update device class in usb device's descriptor
Fetch the device class into usb device's dwcriptors,
so that the host controller's driver can use this info
to differentiate between HUB and DEVICE.

Signed-off-by: Amar <amarendra.xt@samsung.com>
2013-05-05 23:54:22 +02:00
Vivek Gautam
020bbcb76b usb: hub: Power-cycle on root-hub ports
XHCI ports are powered on after a H/W reset, however
EHCI ports are not. So disabling and re-enabling power
on all ports invariably.

Signed-off-by: Amar <amarendra.xt@samsung.com>
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
2013-05-05 23:54:22 +02:00
Vivek Gautam
605bd75af5 USB: Some cleanup prior to USB 3.0 interface addition
Some cleanup in usb framework, nothing much on feature side.

Signed-off-by: Vikas C Sajjan <vikas.sajjan@samsung.com>
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
2013-05-05 23:54:22 +02:00
Vivek Gautam
ceb4972a8f usb: common: Weed out USB_**_PRINTFs from usb framework
USB_PRINTF, USB_HUB_PRINTF, USB_STOR_PRINTF, USB_KBD_PRINTF
are nothing but conditional debug prints, depending on DEBUG.
So better remove them and use debug() simply.

Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
2013-05-05 23:54:21 +02:00
Julius Werner
7d9aa8fd87 usb: Add new command to set USB 2.0 port test modes
This patch adds a new 'usb test' command, that will set a port to a USB
2.0 test mode (see USB 2.0 spec 7.1.20). It supports all five test modes
on both downstream hub ports and ordinary device's upstream ports. In
addition, it supports EHCI root hub ports.

Signed-off-by: Julius Werner <jwerner@chromium.org>
2013-05-05 23:54:21 +02:00
Jim Lin
b068deb363 USB: EHCI: Add weak functions to support new chip
Add ehci_get_port_speed() and ehci_set_usbmode() weak functions
for platform driver to support new chip.

Signed-off-by: Jim Lin <jilin@nvidia.com>
2013-05-05 23:46:41 +02:00
Tom Rini
5ed6f447af P1022DS: Set CONFIG_SPL_MAX_SIZE directly
With the u-boot-with-spl.bin rule calling $(OBJCOPY) with
CONFIG_SPL_PAD_TO, and CONFIG_SPL_PAD_TO defaulting to
CONFIG_SPL_MAX_SIZE we cannot use math here, so set it to 4096 rather
than 4 * 1024.

Signed-off-by: Tom Rini <trini@ti.com>
2013-05-03 09:19:43 -04:00
Tom Rini
3fe0128540 Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx 2013-05-02 19:54:32 -04:00
Shaohui Xie
9e186857c7 powerpc/85xx: set USB2 default mode to 'device' for (super)hydra boards
The Hydra and Superhydra (P3041DS, P5020DS, and P5040DS) boards have a
second USB port that can be configured in either host, peripheral (aka
device), or OTG (on-the-go) mode.  When configured in host mode, if
the port is connected to another USB host, damage to the board can
occur.

To avoid this, we change the default setting to peripheral mode.  Ideally,
we'd set it to OTG mode, but currently there is no OTG support for
these boards.

Setting the hwconfig variable will also update the device tree, and so
Linux will configure the port for peripheral mode as well.

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-02 16:57:34 -05:00
Xu Jiucheng
545c12cf9a powerpc/p1_p2_rdb_pc: Add a pin to reset the DDR chip for P1021RDB-PC
When P1021RDB-PC reboot system, the board will hung at uboot DDR
configuration. For P1021RDB-PC DDR reset pin is multiplex with
QE, so uboot will reserve this pin for QE and skip DDR reset.
Other platforms without QE will do this reset. This patch adds
a slight code to reset DDR chip by QE CE_PB8 pin for NAND and
NOR FLASH boot. For booting from SPI FALSH and SD card, it
seems possible to use the rom on chip to write to the GPIO
pins before configuring the DDR.

Signed-off-by: Xu Jiucheng <B37781@freescale.com>
Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-02 16:57:34 -05:00
Cristian Sovaiala
1f06c9af31 powerpc/mpc85xx: Changed LIODN offset values
Extending LIODN offset range from 1-5 to 1-10
While using a qman portal with a higher index the LIODN offset
is incorrectly set, thus extending the range of offsets covers
all 10 qman portals

Signed-off-by: Cristian Sovaiala <cristian.sovaiala@freescale.com>
Acked-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-02 16:57:34 -05:00
York Sun
e22be77a4a powerpc/mpc85xx: Extend workaround for erratum DDR_A003 to other SoCs
Erratum DDR_A003 applies to P5020, P3041, P4080, P3060, P2041, P5040.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-02 16:57:33 -05:00
Shengzhou Liu
06c1179637 powerpc/p1010rdb: add readme document for p1010rdb
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-02 16:57:33 -05:00
Shengzhou Liu
f68a730538 powerpc/p1010rdb: Change flexcan compatible string
Change flexcan compatible string from "fsl,flexcan-v1.0"
to "fsl,p1010-flexcan" to match the device tree.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-02 16:57:33 -05:00
Timur Tabi
ca9131c056 powerpc/85xx: add SerDes bank 4 lanes
Only some chips have four SerDes banks, so don't define lanes for a bank
that doesn't exist.

Signed-off-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-02 16:56:45 -05:00
Zhicheng Fan
7d83b79c2b qoriq/p1_p2_rdb_pc: USB device-tree fixups for P1020
Resolve P1020 second USB controller multiplexing with eLBC
         - mandatory to mention USB2 in hwconfig string to select it
           over eLBC, otherwise USB2 node is removed
         - works only for SPI and SD boot

Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Zhicheng Fan <B32736@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-02 16:56:45 -05:00
Poonam Aggrwal
56376c4288 doc/ramboot.mpc85xx: Documented the RAMBOOT for MPC85xx
There could be scenarios where the user would like to manually(via JTAG)
configure the DDR/L2SRAM and load the bootloader binary onto DDR/L2SRAM.
This document explains thse usecases and the detailed explanation of what needs
to be done to use it.

Most of the code from CONFIG_SYS_RAMBOOT will be used except for small changes
of CCSRBAR etc.

The changes are not very large, but it is good to document them so that user
can get it working at once.

Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-02 16:56:45 -05:00
Prabhakar Kushwaha
f153b682b3 powerpc/mpc85xx:IFC Errata A003399 is not valid for BSC913x
As per Errata list of BSC9131 and BSC9132, IFC Errata A003399 is no more
valid. So donot compile its workaround.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-02 16:56:44 -05:00
Horst Kronstorfer
df616cae64 mpc85xx: Fix a compiler warning when CONFIG_WATCHDOG is turned on
cpu.c:288:2:
warning: implicit declaration of function 'reset_85xx_watchdog'
[-Wimplicit-function-declaration]

Signed-off-by: Horst Kronstorfer <hkronsto@frequentis.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-02 16:56:44 -05:00
Xulei
99d7b0a43d powerpc/85xx: Add workaround for errata USB-14 (enable on P204x/P3041/P50x0)
On P204x/P304x/P50x0 Rev1.0, USB transmit will result in false internal
multi-bit ECC errors, which has impact on performance, so software should
disable all ECC reporting from USB1 and USB2.

In formal release document, the errata number should be USB14 instead of USB138.

Signed-off-by: xulei <Lei.Xu@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: xulei <B33228@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-02 16:56:44 -05:00
Liu Gang
57966101c8 powerpc/b4860qds: Add the tlb entries for SRIO interfaces
Add the tlb entries based on the configuration of the SRIO interfaces.
Every SRIO interface has 256M space:

	#define CONFIG_SYS_SRIO1_MEM_VIRT   0xa0000000
	#define CONFIG_SYS_SRIO1_MEM_PHYS   0xc20000000ull

	#define CONFIG_SYS_SRIO2_MEM_VIRT   0xb0000000
	#define CONFIG_SYS_SRIO2_MEM_PHYS   0xc30000000ull

Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-02 16:56:44 -05:00
Zang Roy-R61911
c5729f0b1f fman/mEMAC: set SETSP bit in IF_MODE regisgter for RGMII speed
Some legacy RGMII phys don't have in band signaling for the
speed information. so set the RGMII MAC mode according to
the speed got from PHY.

Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Reported-by: John Traill <john.traill@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-02 16:56:44 -05:00
Tang Yuantian
7b700d2125 powerpc/mpc85xx: set clock-frequency for T4/B4 clockgen node
For T4/B4, the clockgen node compatible string is updated to version 2.
Add clock-frequency setting for this new version.

Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-02 16:56:43 -05:00
Shengzhou Liu
04feb57f89 powerpc/b4860: Adding workaround errata A-005871
Per the latest errata updated, B4860/B4420 Rev 1.0 has also
errata A-005871, so adding define A-005871 for B4 SoCs.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-02 16:56:43 -05:00
Liu Gang
ada961e2fc powerpc/b4: Fix the wrong register offset of B4 PCIE module
B4420/B4860 PCIE can not work because of the wrong definition of
the PCIE register offset in the file:
	arch/powerpc/include/asm/immap_85xx.h

Add the judgement of B4420/B4860 to make the register offset to:
	#define CONFIG_SYS_MPC85xx_PCIE1_OFFSET         0x200000

Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-02 16:56:43 -05:00
Matthew McClintock
f45210d6e7 powerpc/p1022ds: Add support for NAND and NAND boot using SPL
Add defines needed to access NAND, remove second flash bank that is
actually connected to NAND.

Add nand booting support for P1022DS with hardcoded DDR config using
SPL framework from 2011

Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Jiang Yutang <b14898@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-02 16:56:43 -05:00
Dongsheng.wang@freescale.com
f5c2623d80 powerpc/mpc85xx: add setting of clock-frequency for mpic node
Set the device tree property associated with the mpic source
frequency. The frequency is used for mpic timer.

Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-02 16:56:42 -05:00
Jeffrey Ladouceur
3c1bfc04c6 powerpc/mpc85xx: Add revision properties in portal device tree node 'pme'
The 'fsl,pme-rev1' and 'fsl-pme-rev2' properties have been added to the
pme portal node. This is required for software to determine which version
of PME hardware is present and take appropriate actions.
These properties are a direct reflection of the corresponding ccsr pme
register value.

Also removed unnecessary static global variables.

Signed-off-by: Jeffrey Ladouceur <Jeffrey.Ladouceur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-02 16:56:42 -05:00
Jiang Bin
acac075b94 board/freescale/common/cds_pci_ft.c: Fix rotate wrong cells in interrupt-map property
For linux 3.x, the size of each item in interrupt-map property is 9 not 7.
Don't use the static value and calculate the size with following cells:
	PCI #address-cells, PCI #interrupt-cells,
	PIC address, PIC #address-cells, PIC #interrupt-cells.

Signed-off-by: Bin Jiang <bin.jiang@windriver.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-02 16:56:42 -05:00
Tom Rini
e3288e1d15 Merge branch 'master' of git://git.denx.de/u-boot-mpc5xxx 2013-05-02 16:21:20 -04:00
Stefan Roese
8aa3449972 mpc5200: a3m071/a4m2k: Miscellaneous updates and fixes
The changes to a3m071/a4m2k in summary are:
- Enable CAN1 on I2C in GPS Port Configuration
- Enable SPI on PSC2
- Activate network console
- New flash partitioning
- Fix some typos
- Pass host name to Linux
- Change rootfs to squashfs,jffs2
- Enable UBI/UBIFS support
- Enable FIT support

Signed-off-by: Stefan Roese <sr@denx.de>
2013-05-02 20:46:08 +02:00
Stefan Roese
704afcc43f mpc5200: a3m071/a4m2k: Fix problem with increased global_data struct
The v2013.04 release has this patch set included:

5cb48582 "Add architecture-specific global data"

With this, the global_data struct is now common and new variables
have been added. Resulting in a bigger struct. Unfortunately the
currently allocated 128 bytes are just a bit too small for this
new struct.

This patch now uses the automatically generated struct size instead to
not run into this problem again.

Please note that this problem might hit some other platforms which
currently reserve a tight space of 128 bytes for the global_data
struct!

Signed-off-by: Stefan Roese <sr@denx.de>
2013-05-02 20:45:44 +02:00
Stefan Roese
f8945518ca mpc5200: a3m071/a4m2k: Enable flash verify option
Signed-off-by: Stefan Roese <sr@denx.de>
2013-05-02 20:44:36 +02:00
Anatolij Gustschin
b91363cd34 mpc512x: remove dead code
The prt_mpc512x_clks() function isn't referenced
anywhere and its prototype is wrong. Remove it.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
2013-05-02 20:43:38 +02:00
Tom Rini
63216de134 omap5_uevm: Enable redundant MMC environment
Cc: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
2013-05-01 16:41:10 -04:00
Tom Rini
da85c9c813 mx28evk: Guard NAND-related ENV defines with CONFIG_ENV_IS_IN_NAND
The redundancy related defines are only correct for NAND, so guard all
of that area with CONFIG_ENV_IS_IN_NAND

Cc: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Tom Rini <trini@ti.com>
2013-05-01 16:41:10 -04:00
Michael Heimpold
d196bd8803 env_mmc: add support for redundant environment
This patch add support for storing the environment redundant on
mmc devices. Substantially it re-uses the logic from the NAND implementation,
that means using an incremental counter for marking newer data.

Signed-off-by: Michael Heimpold <mhei@heimpold.de>
2013-05-01 16:41:10 -04:00
Andreas Bießmann
d2eae43ba8 lib: consolidate hang()
Delete all occurrences of hang() and provide a generic function.

Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Acked-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
[trini: Modify check around puts() in hang.c slightly]
Signed-off-by: Tom Rini <trini@ti.com>
2013-05-01 16:41:08 -04:00
Andreas Bießmann
b0dac5b1af tx25: add CONFIG_SPL_LIBGENERIC_SUPPORT
In order to use the generic hang() later on pull libgeneric in SPL.
This has no impact on the SPL size.

Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-05-01 16:24:03 -04:00
Andreas Bießmann
b157315353 mx31pdk: add CONFIG_SPL_LIBGENERIC_SUPPORT
In order to use the generic hang() later on pull libgeneric in SPL.
This has no impact on the SPL size.

Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-05-01 16:24:02 -04:00
Andreas Bießmann
63495ad77a nios2: fix style in board.c.
Make nios2's board.c checkpatch clean.

Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-05-01 16:24:02 -04:00
Andreas Bießmann
50ffb1174c microblaze: fix style in board.c
Make microblaze's board.c checkpatch clean.

Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

Reviewed-by: Michal Simek <monstr@monstr.eu>
2013-05-01 16:24:02 -04:00
Egbert Eich
0472fbfd32 part/dev_desc: Add log2 of blocksize to block_dev_desc data struct
log2 of the device block size serves as the shift value used to calculate
the block number to read in file systems when implementing avaiable block
sizes.
It is needed quite often in file systems thus it is pre-calculated and
stored in the block device descriptor.

Signed-off-by: Egbert Eich <eich@suse.com>
2013-05-01 16:24:02 -04:00
Egbert Eich
bc8d98713f fs/fat: Don't multiply fatsize with sector size
Bugfix:
Here at this place we need the fat size in sectors not bytes.
This was found during code review when adding support for storage
devices with blocksizes != 512.

Signed-off-by: Egbert Eich <eich@suse.com>
2013-05-01 16:24:02 -04:00
Egbert Eich
d7ea4d4d4c disk/iso: Add Support for block sizes > 512 byte to ISO partition support
For ISO we check the block size of the device if this is != the CD sector
size we assume that the device has no ISO partition.

Signed-off-by: Egbert Eich <eich@suse.com>
2013-05-01 16:24:02 -04:00
Egbert Eich
ae1768a72c disk/gpt: Fix GPT partition handling for blocksize != 512
Disks beyond 2T in size use blocksizes of 4096 bytes. However a lot of
code in u-boot  still assumes a 512 byte blocksize.
This patch fixes the handling of GPTs.

Signed-off-by: Egbert Eich <eich@suse.com>
2013-05-01 16:24:02 -04:00