Commit graph

24 commits

Author SHA1 Message Date
Simon Glass
e7dcf5645f env: Drop environment.h header file where not needed
This header file is now only used by files that access internal
environment features. Drop it from various places where it is not needed.

Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
2019-08-11 16:43:41 -04:00
Simon Glass
9fb625ce05 env: Move env_set() to env.h
Move env_set() over to the new header file.

Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
2019-08-11 16:43:41 -04:00
Ludwig Zenz
4a6f5b4f56 ARM: imx6: DHCOM i.MX6 PDK: Switch to DM for I2C
This patch enables DM I2C for DHCOM i.MX6 PDK2 boards and
removes non DM I2C code. The I2C EEPROM with ethaddr (MAC)
is defined in the device tree. Use UCLASS_I2C_EEPROM
to find the device by fixed hardware path and read the ethaddr.

Tested with DHCOM i.MX6dl and DHCOM i.MX6q.

Signed-off-by: Ludwig Zenz <lzenz@dh-electronics.com>
Reviewed-by: Marek Vasut <marex@denx.de>
2019-07-19 20:32:24 +02:00
Ludwig Zenz
6e75cb237d ARM: imx6: DHCOM i.MX6 PDK: enable pad pull ups of SS lines of spi used for boot
It turned out that after a reset the boot process from the spi bootflash is
disturbed by other spi slave devices connected to DHCOM SPI1, which uses the
same spi interface with a different SS line.

Therefore the pad pull ups are enabled.

Signed-off-by: Ludwig Zenz <lzenz@dh-electronics.com>
2019-07-19 20:32:24 +02:00
Ludwig Zenz
8039211a8a ARM: imx6: DHCOM i.MX6 PDK: config SPL to load U-Boot fitImage with mulitple DTs
Configure fitImage for U-Boot with a device tree for imx6 quad/dual
and duallite/solo. This enables to support the imx6 derivates
quad/dual/duallite/solo with a single binary.

Signed-off-by: Ludwig Zenz <lzenz@dh-electronics.com>
Reviewed-by: Marek Vasut <marex@denx.de>
2019-07-19 20:32:24 +02:00
Marek Vasut
4ca99fe81a ARM: imx: dh-imx6: Enable DM regulator
Enable DM support for regulators and fixed regulator driver and
convert USB Vbus control over to the regulators defined in DT.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Ludwig Zenz <lzenz@dh-electronics.com>
Cc: Stefano Babic <sbabic@denx.de>
Tested-by: Ludwig Zenz <lzenz@dh-electronics.com>
2019-07-19 20:14:50 +02:00
Yangbo Lu
e37ac717d7 Convert to use fsl_esdhc_imx for i.MX platforms
Converted to use fsl_esdhc_imx for i.MX platforms.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Tested-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Martyn Welch <martyn.welch@collabora.com>
Acked-by: Jason Liu <Jason.hui.liu@nxp.com>
2019-06-23 14:18:34 +08:00
Marek Vasut
cc48c2a5cf ARM: imx: dh-imx6: Convert SPI support to DM
Enable DM SPI and SF support on DHCOM iMX6 PDK2.
Convert board code to match the DM support.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Ludwig Zenz <lzenz@dh-electronics.com>
Cc: Stefano Babic <sbabic@denx.de>
2019-06-11 10:42:48 +02:00
Marek Vasut
0050c929c2 ARM: imx: dh-imx6: Convert SATA support to DM
Enable DM SATA support on DHCOM iMX6 PDK2.
Convert board code to match the DM support.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Ludwig Zenz <lzenz@dh-electronics.com>
Cc: Stefano Babic <sbabic@denx.de>
2019-06-11 10:42:48 +02:00
Marek Vasut
198fee844b ARM: imx: dh-imx6: Convert SD/MMC support to DM
Enable DM block and DM MMC support on DHCOM iMX6 PDK2.
Convert board code to match the DM support.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Ludwig Zenz <lzenz@dh-electronics.com>
Cc: Stefano Babic <sbabic@denx.de>
2019-06-11 10:42:48 +02:00
Marek Vasut
3a05eb8fee ARM: imx: dh-imx6: Enable DM GPIO
Enable DM GPIO support on DHCOM iMX6 PDK2 and fix up board code
where applicable.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Ludwig Zenz <lzenz@dh-electronics.com>
Cc: Stefano Babic <sbabic@denx.de>
2019-06-11 10:42:48 +02:00
Ludwig Zenz
aa34505653 ARM: imx6: DHCOM i.MX6 PDK: use Kconfig for inclusion of DDR calibration
The four x16 DDR3 are wired in T-topology. From NXP AN4467:
'Although not required, T-Topologies may also benefit from performing
Write Leveling as there are package delays on both the processor and DDR
devices that can be de-skewed by performing Write Leveling. Therefore,
Freescale recommends determining Write Leveling calibration parameters
for all boards, regardless of topology used.'
That is why write level calibration is also done.

Signed-off-by: Ludwig Zenz <lzenz@dh-electronics.com>
2019-04-25 19:16:24 +02:00
Ludwig Zenz
a44ca1346d ARM: imx6: update 1GB DDR3 calibration for DHCOM i.MX6qd PDK
The existing calibration values were found to be incorrect
in comparison to newly determined values.

The new values were generated with the help of 5 boards. They have
been determined with the NXP Utility 'DDR Stress Test (2.9.0)'.

Signed-off-by: Ludwig Zenz <lzenz@dh-electronics.com>
2019-04-25 19:16:24 +02:00
Ludwig Zenz
0481bef035 ARM: imx6: DHCOM i.MX6 PDK: ddr init for 32bit bus and 4GBit chips
Support 1GIB + 2GIB DDR3 with 64bit bus width and 512MIB + 1GIB with 32bit bus width

Signed-off-by: Ludwig Zenz <lzenz@dh-electronics.de>
2018-07-23 11:02:14 +02:00
Ludwig Zenz
659ca2dd08 ARM: imx6: configure ddrcode pins in spl DHCOM i.MX6 PDK
Preperation for conditional DDR3 initialization based on GPIO codes.

Signed-off-by: Ludwig Zenz <lzenz@dh-electronics.de>
2018-07-23 11:02:03 +02:00
Ludwig Zenz
3d81584d40 Revert "ARM: imx6: Disable DDR DRAM calibration DHCOM i.MX6 PDK"
This reverts commit a637fe6f27.

The DDR DRAM calibration was enhanced by write leveling correction code.
It can be used with T-topology now.

Signed-off-by: Ludwig Zenz <lzenz@dh-electronics.de>
2018-07-23 11:01:41 +02:00
Tom Rini
83d290c56f SPDX: Convert all of our single license tags to Linux Kernel style
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from.  So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry.  Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents.  There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-07 09:34:12 -04:00
Tom Rini
d024236e5a Remove unnecessary instances of DECLARE_GLOBAL_DATA_PTR
We have a large number of places where while we historically referenced
gd in the code we no longer do, as well as cases where the code added
that line "just in case" during development and never dropped it.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-27 14:54:48 -04:00
Alex Kiernan
9925f1dbc3 net: Move enetaddr env access code to env config instead of net config
In order that we can use eth_env_* even when CONFIG_NET isn't set, move
these functions to environment code from net code.

This fixes failures such as:

  board/ti/am335x/built-in.o: In function `board_late_init':
  board/ti/am335x/board.c:752: undefined reference to `eth_env_set_enetaddr'
  u-boot/board/ti/am335x/board.c:766: undefined reference to `eth_env_set_enetaddr'

which caters for use cases such as:

commit f411b5cca4 ("board: am335x: Always set eth/eth1addr environment
variable")

when Ethernet is required in Linux, but not U-Boot.

Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
2018-04-08 23:00:58 -04:00
Marek Vasut
a637fe6f27 ARM: imx6: Disable DDR DRAM calibration DHCOM i.MX6 PDK
The DDR DRAM calibration doesn't work on T-topology sometimes, so disable it.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
2017-12-29 11:18:59 +01:00
Marek Vasut
b979e35230 ARM: imx6: Adjust DDR DRAM settings on DHCOM i.MX6 PDK
The board uses T-topology for the four x16 DRAM chips, so remove
the write-leveling from the SPL as that is only usefly on fly-by
topology and can be harmful on T-topology. Also update the DRAM
timing with values from calibration on multiple boards.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
2017-11-16 10:43:22 +01:00
Tom Rini
79df00fdb4 MAINTAINERS: Add missing boards and config entries
As part of my usual round of build testing, output about missing
MAINTAINERS information was not logged, and thus often overlooked.
Correct that mistake by ensuring that I log the output of
genboardscfg.py every time.  As part of that, address a number of
missing MAINTAINERS entires.  In the case of a missing file, I have put
the original submitter down.  In the rest of the cases I have added the
config (and sometimes relevant header file) to the existing set of file
globs.

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-11-06 09:58:51 -05:00
Marek Vasut
506abdb4ee ARM: imx6: Enable UMS and DFU on DHCOM i.MX6 PDK
Enable UMS and DFU, so that the eMMC can be accessed via the
USB gadget port on the board.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
2017-10-31 11:11:10 +01:00
Marek Vasut
0a333602df ARM: imx6: Add DHCOM i.MX6 PDK board support
Add support for the DHCOM i.MX6 PDK board. This board has:
- FEC ethernet
- EHCI USB host
- 3x SDMMC

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
2017-10-12 18:01:06 +02:00