Move the crypto and sec_jr* nodes from board-specific
u-boot.dtsi files into the common files. Additionally protect the
nodes with ifdef CONFIG_FSL_CAAM as they don't serve any purpose if
that is not enabled.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
There is no need to include the firmware/optee node if the optee
driver is not enabled.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Move the firmware/optee node to the common imx8mp-u-boot.dtsi and
protect it with an ifdef CONFIG_OPTEE as it is a meaningless node
without the optee driver enabled.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Move the firmware/optee node to the common imx8mm-u-boot.dtsi and
protect it with an ifdef CONFIG_OPTEE as it is a meaningless node
without the optee driver enabled.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Enable USB SDP SPL aka serial downloader recovery mode support.
While at it also enable fastboot support which may be used to
subsequently load further stages like a Toradex Easy Installer FIT
image.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Update the imx8mp-venice-gw74xx for revB:
- add CAN1
- add TIS-TPM on SPI2
- add FAN controller
- fix PMIC I2C bus (revA PMIC I2C was non-functional so no need for
backward compatible option)
- M2 socket GPIO's moved
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The Gateworks imx8mm-venice-gw7905-0x consists of a SOM + baseboard.
The GW700x SOM contains the following:
- i.MX8M Mini SoC
- LPDDR4 memory
- eMMC Boot device
- Gateworks System Controller (GSC) with integrated EEPROM, button
controller, and ADC's
- RGMII PHY
- PMIC
- SOM connector providing:
- FEC GbE MII
- 1x SPI
- 2x I2C
- 4x UART
- 2x USB 2.0
- 1x PCI
- 1x SDIO (4-bit 3.3V)
- 1x SDIO (4-bit 3.3V/1.8V)
- GPIO
The GW7905 Baseboard contains the following:
- GPS
- microSD
- off-board I/O connector with I2C, SPI, GPIO
- EERPOM
- PCIe clock generator
- 1x full-length miniPCIe socket with PCI/USB3 (via mux) and USB2.0
- 1x half-length miniPCIe socket with USB2.0 and USB3.0
- USB 3.0 HUB
- USB Type-C with USB PD Sink capability and peripheral support
- USB Type-C with USB 3.0 host support
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The Gateworks imx8mp-venice-gw73xx-2x consists of a SOM + baseboard.
The GW702x SOM contains the following:
- i.MX8M Plus SoC
- LPDDR4 memory
- eMMC Boot device
- Gateworks System Controller (GSC) with integrated EEPROM, button
controller, and ADC's
- PMIC
- SOM connector providing:
- eQoS GbE MII
- 1x SPI
- 2x I2C
- 4x UART
- 2x USB 3.0
- 1x PCI
- 1x SDIO (4-bit 3.3V)
- 1x SDIO (4-bit 3.3V/1.8V)
- GPIO
The GW73xx Baseboard contains the following:
- 1x RJ45 GbE (eQoS from SOM)
- 1x RJ45 GbE (PCI)
- off-board I/O connector with MIPI-CSI (3-lane), MIPI-DSI (4-lane),
- off-board I/O connector with RS232/RS485
- off-board I/O connector with SPI
- off-board I/O connector with I2C, UART, and GPIO
I2C, I2S and GPIO
- microSD (1.8V/3.3V)
- GPS
- Accelerometer
- EERPOM
- USB 3.0 Hub
- Front Panel bi-color LED
- re-chargeable battery (for RTC)
- PCIe clock generator
- PCIe switch
- on-board 802.11abgnac 1x1 WiFi and Bluetooth 5.2
- 1x USB Type-A host socket with USB 3.0 support
- 1x USB OTG with USB 2.0 support
- 2x MiniPCIe socket with PCI and USB 2.0
- 1x MiniPCIe socket with SIM, PCI/USB 3.0 (mux), and USB 2.0
- Wide range DC input supply
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The Gateworks imx8mp-venice-gw72xx-2x consists of a SOM + baseboard.
The GW702x SOM contains the following:
- i.MX8M Plus SoC
- LPDDR4 memory
- eMMC Boot device
- Gateworks System Controller (GSC) with integrated EEPROM, button
controller, and ADC's
- PMIC
- SOM connector providing:
- eQoS GbE MII
- 1x SPI
- 2x I2C
- 4x UART
- 2x USB 3.0
- 1x PCI
- 1x SDIO (4-bit 3.3V)
- 1x SDIO (4-bit 3.3V/1.8V)
- GPIO
The GW72xx Baseboard contains the following:
- 1x RJ45 GbE (eQoS from SOM)
- 1x RJ45 GbE (PCI)
- off-board I/O connector with MIPI-CSI (3-lane), MIPI-DSI (4-lane),
- off-board I/O connector with RS232/RS485
- off-board I/O connector with SPI
- off-board I/O connector with I2C, UART, and GPIO
I2C, I2S and GPIO
- microSD (1.8V/3.3V)
- GPS
- Accelerometer
- EERPOM
- USB 3.0 Hub
- Front Panel bi-color LED
- re-chargeable battery (for RTC)
- PCIe clock generator
- PCIe switch
- 1x USB Type-A host socket with USB 3.0 support
- 1x USB OTG with USB 2.0 support
- 1x MiniPCIe socket with PCI and USB 2.0
- 1x MiniPCIe socket with SIM, PCI/USB 3.0 (mux), and USB 2.0
- Wide range DC input supply
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Linux microPlatform uses an rngb device in optee-os in boot scheme
SPL -> OPTEE -> U-Boot. To make rngb available for optee-os, enable
it in SPL.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Co-developed-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
With enabled SKIP_LOWLEVEL_INIT, the weak function timer_init() is
used in the SPL build. For iMX6 SoC, this leads MMC to fail once
u-boot proper is booted due to a timing issue.
Always use iMX-specific timer_init() in SPL to fix timing issues.
Fixes: be277c3a89 ("imx: mx7: avoid some initialization if low level is skipped")
Signed-off-by: Michael Scott <mike@foundries.io>
Co-developed-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Now we have to use UCLASS_SM driver instead of
raw smc_call() function call.
Signed-off-by: Alexey Romanov <avromanov@salutedevices.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Link: https://lore.kernel.org/r/20230921081346.22157-9-avromanov@salutedevices.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
The common.h header should always be first, followed
by other headers in order, then headers with directories,
then local files.
Signed-off-by: Alexey Romanov <avromanov@salutedevices.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Link: https://lore.kernel.org/r/20230921081346.22157-8-avromanov@salutedevices.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
This patch adds an implementation of the Meson Secure Monitor
driver based on UCLASS_SM.
Signed-off-by: Alexey Romanov <avromanov@salutedevices.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Link: https://lore.kernel.org/r/20230921081346.22157-7-avromanov@salutedevices.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
At the moment, we don't have a common API for working with
SM, only the smc_call() function. This approach is not generic
and difficult to configure and maintain.
This patch adds UCLASS_SM with the generic API:
- sm_call()
- sm_call_write()
- sm_call_read()
These functions operate with struct pt_regs, which describes
Secure Monitor arguments.
Signed-off-by: Alexey Romanov <avromanov@salutedevices.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Link: https://lore.kernel.org/r/20230921081346.22157-2-avromanov@salutedevices.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
scan all entries in multi-device boot_targets
EFI empty-capsule support
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmUpvTQRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreabCwgAimB2fGpK3FjFMrH1Ko4Qh3j0D/0XomiQ
1KYVbn3YrswLmq1tav9HSKWR3Ep/Uet6jthpH2RPxhcGWNGqxkkk2k4LUudSlIYd
0KKoovMwBK9jZcojoBAjFGaoRIaEBlbFspW/RoXPJnr7ctxf6HSYkW2TPH09zqtD
FrL5Jjf6t0h6QShxhCYXbiHGCnp2zYZRzFnrYpaXy8IIavqWNJTAhkIGveMy+Qa8
TzhmuRamLgtZZwtFcHt8sZuV4+FtBrtHAyiEasnJFPJ5Kv6tFVBiHdYuygZMu/og
+F57ufgqgHTlDjzW72CJyhrHIcVn/mWjNYrulufqHAsSFD7cizISeA==
=qOUT
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-13oct23' of https://source.denx.de/u-boot/custodians/u-boot-dm
improvements with dev_read_addr_..._ptr()
scan all entries in multi-device boot_targets
EFI empty-capsule support
- Fix a memset call in the optee_agent code.
Then to quote the author for the rest of the changes:
This patch series allows users to access SCMI base protocol provided by
SCMI server (platform). See SCMI specification document v3.2 beta[1]
for more details about SCMI base protocol.
What is currently not implemented is
- SCMI_BASE_NOTIFY_ERRORS command and notification callback mechanism
This feature won't be very useful in the current U-Boot environment.
[1] https://developer.arm.com/documentation/den0056/e/?lang=en
The sess variable in open_channel was not entirely
cleared to zero at the start of this function.
This commit ensures that the entire struct is cleared.
Signed-off-by: Francois Berder <fberder@outlook.fr>
Now that we have Base protocol support, we will be able to check if a given
protocol is really supported by the SCMI server (firmware).
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Etienne Carriere <etienne.carriere@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Added is a new unit test for SCMI base protocol, which will exercise all
the commands provided by the protocol, except SCMI_BASE_NOTIFY_ERRORS.
$ ut dm scmi_base
It is assumed that test.dtb is used as sandbox's device tree.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Etienne Carriere <etienne.carriere@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
SCMI base protocol is mandatory and doesn't need to be listed in a device
tree.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Etienne Carriere <etienne.carriere@foss.st.com>
SCMI base protocol is mandatory, and once SCMI node is found in a device
tree, the protocol handle (udevice) is unconditionally installed to
the agent. Then basic information will be retrieved from SCMI server via
the protocol and saved into the agent instance's local storage.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Etienne Carriere <etienne.carriere@foss.st.com>
Adding SCMI base protocol makes it inconvenient to hold the agent instance
(udevice) locally since the agent device will be re-created per each test.
Just remove it and simplify the test flows.
The test scenario is not changed at all.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Etienne Carriere <etienne.carriere@foss.st.com>
This is a simple implementation of SCMI base protocol for sandbox.
The main use is in SCMI unit test.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Etienne Carriere <etienne.carriere@foss.st.com>
In SCMI base protocol version 2 (0x20000), new interfaces,
BASE_SET_DEVICE_PERMISSIONS/BASE_SET_PROTOCOL_PERMISSIONS/
BASE_RESET_AGENT_CONFIGURATION, were added. Moreover, the api of
BASE_DISCOVER_AGENT was changed to support self-agent discovery.
So the driver expects SCMI firmware support version 2 of base protocol.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Etienne Carriere <etienne.carriere@foss.st.com>
SCMI base protocol is mandatory according to the SCMI specification.
With this patch, SCMI base protocol can be accessed via SCMI transport
layers. All the commands, except SCMI_BASE_NOTIFY_ERRORS, are supported.
This is because U-Boot doesn't support interrupts and the current transport
layers are not able to handle asynchronous messages properly.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Etienne Carriere <etienne.carriere@foss.st.com>
Any SCMI protocol may have its own channel.
Test this feature on sandbox as the necessary framework was added
in a prior commit.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Etienne Carriere <etienne.carriere@foss.st.com>
This framework allows SCMI protocols to be installed and bound to the agent
so that the agent can manage and utilize them later.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Etienne Carriere <etienne.carriere@foss.st.com>
Move the location of scmi_bind_protocols() backward for changes
in later patches.
There is no change in functionality.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Etienne Carriere <etienne.carriere@foss.st.com>
In sandbox scmi agent, channels are not used at all. But in this patch,
dummy channels are supported in order to test protocol-specific channels.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Etienne Carriere <etienne.carriere@foss.st.com>
SCMI specification allows any protocol to have its own channel for
the transport. While the current SCMI driver may assign its channel
from a device tree, the core function, devm_scmi_process_msg(), doesn't
use a protocol's channel, but always use an agent's channel.
With this commit, devm_scmi_process_msg() tries to find and use
a protocol's channel. If it doesn't exist, use an agent's.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Etienne Carriere <etienne.carriere@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The commit 85dc582892 ("firmware: scmi: prepare uclass to pass channel
reference") added an explicit parameter, channel, but it seems to make
the code complex.
Hiding this parameter will allow for adding a generic (protocol-agnostic)
helper function, i.e. for PROTOCOL_VERSION, in a later patch.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Etienne Carriere <etienne.carriere@foss.st.com>
Add support in binman for generating EFI empty capsules. These
capsules are used in the FWU A/B update feature. Also add test cases
in binman for the corresponding code coverage.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a method to the mkeficapsule bintool to generate empty
capsules. These are capsules needed for the FWU A/B update feature.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
The various fields of a generated capsule are currently verified
through hard-coded offsets. Use the dump-capsule feature for dumping
the capsule header contents and use those for capsule verification.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
The #address-cells and #size-cells are not needed for running the
capsule generation binman tests. Remove the superfluous properties.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add documentation to explain the printing of the capsule headers
through the mkeficapsule tool.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support to dump the contents of capsule headers. This is useful as
a debug feature for checking the contents of the capsule headers, and
can also be used in capsule verification.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
A follow-up to commit 842fb5de42
("drivers: use devfdt_get_addr_size_index_ptr when cast to pointer")
and commit 320a1938b6
("drivers: use devfdt_get_addr_index_ptr when cast to pointer").
In addition to using the *_ptr variants of these functions where the
address is cast to a pointer, this also changes devfdt_get_addr_*() to
dev_read_addr_*() in a few places. Some variable and field types are
changed from fdt_addr_t or phys_addr_t to void* where the cast was
happening later.
This patch fixes a number of compile warnings when building a 32bit
U-Boot with CONFIG_PHYS_64BIT=y. In some places, it also fixes error
handling where the return value of dev_read_addr() etc. was checked for
NULL instead of FDT_ADDR_T_NONE.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
pinctrl-single uses fdt_addr_t and phys_addr_t inconsistently, but both
are wrong to be passed to readb() etc., which expect a pointer or
pointer-sized integer. Change the driver to use
dev_read_addr_size_index_ptr(), so we consistently deal with void*
(except for the sandbox case and single_get_pin_muxing()).
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add missing mapmem.h header:
Signed-off-by: Simon Glass <sjg@chromium.org>
Same as dev_read_addr_name[_size](), but returns a pointer, cast
through map_sysmem().
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Checking for the error cast to fdt_addr_t is rather awkward - IS_ERR()
can be used, but it's not really made to be used on fdt_addr_t, which
may not even be the same size as a native pointer.
Most places in U-Boot only check for FDT_ADDR_T_NONE; let's adjust the
error return to match the expectation.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
- The dev_read_addr_name*() family of functions has no "index" argument,
doc comments should refer to "name"
- Specify the error return for several devfdt_get_addr*() functions
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The argument type of `build_from_git` was changed from string to list
in d71e711699.
This commit adapts the argument type of all bintools using this
function.
Signed-off-by: Lukas Funke <lukas.funke@weidmueller.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
