Since OMAP's spl doesn't support DM currently, do not define
DM_SPI and DM_SPI_FLASH for spl build.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
enable spi driver model for dra74_evm as ti_qspi supports
driver model
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
enable mmc driver model for dra72_evm as ti_qspi supports
driver model
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
In U-Boot most flashes uses "spi-flash" as compatible to bind the
device to flash driver, so adding "spi-flash" compatible to
m25p80 node.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
In U-Boot most flashes uses "spi-flash" as compatible to bind the
device to flash driver, so adding "spi-flash" compatible to
m25p80 node.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
In U-Boot most flashes uses "spi-flash" as compatible to bind the
device to flash driver, so adding "spi-flash" compatible to
m25p80 node.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Add qspi memory map and control module register maps to device tree.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
adopt ti_qspi driver to device driver model
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
add spi alias for qspi so that spi probes the device and driver
successfully.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Since OMAP's spl doesn't support DM currently, do not define DM_SPI and
DM_SPI_FLASH for spl build.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
spi bus can support dual and quad wire data transfers for tx and
rx. So defining dual and quad modes for both tx and rx. Also add
support to parse bus width used for spi tx and rx transfers.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Changing the ti_qspi_priv structure and its instance names from
to priv for driver mode conversion.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
To enable memory map in dra7xx, specific chip select must be
written to control module register. But this hard coded to chip
select 1, fixing it by writing the specific chip select value to
control module register.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Added SPI_TX_DUAL mode flag.
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Tested-by: Jagan Teki <jteki@openedev.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
- Add comments on mode_rx
- Tab space's
Cc: Simon Glass <sjg@chromium.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Used BIT macro like 1 << nr as BIT(nr) where nr is 0...n
Cc: Simon Glass <sjg@chromium.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Fixed bit assignment with flags members on spi_slave{}
Cc: Simon Glass <sjg@chromium.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
This patch moves flags macro's to respective member
position on spi_slave{}, for better readabilty and
finding the respective member macro's easily.
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Tested-by: Jagan Teki <jteki@openedev.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Since spi rx mode macro's are renamed to simple and
meaninfull, this patch will rename the respective
structure members.
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Tested-by: Jagan Teki <jteki@openedev.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
SPI_OPM_RX_DIO and SPI_OPM_RX_QIOF are rx IO
commands/opmodes for dual and quad. Usually IO
operation's are referred to flash protocol rather
with spi controller protocol, these are still present
in flash side for the usage of spi-nor controllers.
Cc: Simon Glass <sjg@chromium.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
SPI_OPM_RX_EXTN is a combination of all rx opmode's
and spi driver shall use any one of the rx mode at
a time not the combination and it is true in case of
flash where spi_flash_table mention combination of
supported read opmodes so-that the required one
will pick based on the rx mode from spi driver.
Cc: Simon Glass <sjg@chromium.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
While setting quad bit on spansion, macronix code
is writing only particular quad bit this may give
wrong functionality with other register bits,
So this patch fix the issue where it with write
previous read reg status along particular quad bit.
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
One macronix quad bit set using SR, it's good to
read back and check the written bit and also if
it's already been set check for the bit and return.
Cc: Vignesh R <vigneshr@ti.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
One spansion quad bit set using CR, it's good to
read back and check the written bit and also if
it's already been set check for the bit and return.
Cc: Vignesh R <vigneshr@ti.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Setting up quad bit for micron devices need to do the
same way as other flash devices like spansion, winbond
etc does using enhanced volatile config register so this
patch adds this support instead of printing "QEB is volatile"
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Peter Pan <peterpandong@micron.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
- Tab space
- Place all read commands at one place.
- Re-arrange write commands.
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Use direct call to device_remove instead of exctra
spi_flash_remove defination.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
bar_end gives more meaningfull compared to bank_end and
spi_flash_write_bar uses bar_end so replaced bank_end with
bar_end in spi_flash_read_bar
Signed-off-by: Jagan Teki <jteki@openedev.com>
Since spi_read_cmds_array is used locally in
spi_flash_scan, so move array to locally used
function instead of defining global array.
Tested-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Since SPI_TX_* are spi_slave{} members so use spi protocol
notation instead spi flash programming, like
SPI_TX_BP => SPI_TX_BYTE
SPI_TX_QPP => SPI_TX_QUAD
Cc: Simon Glass <sjg@chromium.org>
Tested-by: Jagan Teki <jteki@openedev.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Used mode member from spi_slave{} instead of op_mode_tx.
Cc: Simon Glass <sjg@chromium.org>
Tested-by: Jagan Teki <jteki@openedev.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Couldn't find the exact reason to define 'mode' for dm,
probably it is not using in non-dm drivers but it need
to visible both dm and non-dm as mode data is getting
dereferred in spi flash core ie common to both.
Cc: Simon Glass <sjg@chromium.org>
Tested-by: Jagan Teki <jteki@openedev.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
For better code readabilty, get the spi pointer from
spi_flash{} locally and use it instead of direct
dereferring spi pinter as flash->spi->*
Tested-by: Jagan Teki <jteki@openedev.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
This feature is required in SPL to enable support for loading from SPI
flash.
Also clean up the #define in socfpga_common.h.
Signed-off-by: Nathan Rossi <nathan@nathanrossi.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin-Liang See <clsee@altera.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Select SPL_DM_SEQ_ALIAS which is required for certain uclasses,
specifically SPI Flash.
Signed-off-by: Nathan Rossi <nathan@nathanrossi.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Stefan Roese <sr@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This feature is required in SPL to enable support for loading from SPI
flash when the device is booted from QSPI.
Signed-off-by: Nathan Rossi <nathan@nathanrossi.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The Device Model sequence alias feature is required by some Uclasses.
Instead of disabling the feature for all SPL targets allow it to be
configured.
The config option is disabled by default to reduce code size for targets
that are not interested or do not require this feature.
Signed-off-by: Nathan Rossi <nathan@nathanrossi.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Marek Vasut <marex@denx.de>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Document the usage of 'qfw' command
Signed-off-by: Miao Yan <yanmiaobest@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Remove 'cpu' node in device tree for QEMU targets, and let U-Boot detect
and fix up those information at runtime.
Signed-off-by: Miao Yan <yanmiaobest@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Currently, when booting with more that one CPU enabled, U-Boot scans
'cpu' node in device tree and calculates CPU number. This does not scale
well as changing CPU number also requires modifying .dts and re-compiling
U-Boot.
This patch uses fw_cfg interface provided by QEMU to detect online CPU
number at runtime, and dynamically adds 'cpu' device to U-Boot's driver
model.
Signed-off-by: Miao Yan <yanmiaobest@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Use actual CPU number, instead of maximum cpu configured, to allocate
stack memory in 'load_sipi_vector'
Signed-off-by: Miao Yan <yanmiaobest@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Rename 'find_cpu_by_apid_id' to 'find_cpu_by_apic_id'. This should be a
typo.
Signed-off-by: Miao Yan <yanmiaobest@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a cpu uclass driver for qemu. Previously, the qemu target gets cpu
number from board dts files, which are manually created at compile time.
This does not scale when more cpus are assigned to guest as the dts files
must be modified as well.
This patch adds a cpu uclass driver for qemu targets to directly read
online cpu number from firmware.
Signed-off-by: Miao Yan <yanmiaobest@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
The QEMU fw_cfg interface allows the guest to retrieve various data
information from QEMU. For example, APCI/SMBios tables, number of online
cpus, kernel data and command line, etc.
This patch adds support for QEMU fw_cfg interface.
Signed-off-by: Miao Yan <yanmiaobest@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
By default, ramdisk load address is defined to 02000000 in env string.
When loading bzImage to 01000000 (default address), there's a chance that
the ramdisk header would be overwritten by the kernel. Thus increase the
gap and make ramdisk load at 04000000 by default and also this patch
introduces a new configuration item CONFIG_RAMDISK_ADDR for this purpose
Signed-off-by: Miao Yan <yanmiaobest@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
