The few tests that are Blackfin-specific have been migrated to common
code or been rewritten with the existing "bsp-specific" defines.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
There is no code anywhere that references BOOTFLAG_* so remove these
defines.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Valentin Longchamp <valentin.longchamp@keymile.com>
Cc: Peter Tyser <ptyser@xes-inc.com>
Result of running the following command to address Wolfgang's
comment about camel case:
for file in `find . | grep '\.[chS]$'`; do perl -i -pe
's/(green|yellow|red|blue)_LED_(on|off)/$1_led_$2/g' $file; done
Discussion:
http://patchwork.ozlabs.org/patch/84988/
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Factor out common parts from omap4_sdp4430.h and omap4_panda.h
into a new file omap4_common.h
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Modify the MEMTEST start and end address. The memtest range was overlapping the
CONFIG_SYS_LOAD_ADDR which causes the uImage to be corrupt.Also, modify the
size for which mtest is run to 32MB from 16MB.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Nagabhushana Netagunte <nagabhushana.netagunte@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Enable SPI flash boot mode in configuration file as default.
With the introduction of 456MHz part, SPI operating frequency
will increase and at this frequency SPI does not work correctly.
Hence reduce the default SPI speed to 30MHz from 50MHz.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Nagabhushana Netagunte <nagabhushana.netagunte@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Modify U-boot promt string from 'DA830-evm >' to 'U-Boot >' as
there are many variants of da830 based boards which have diffrent
names such as L137, AM1707 etc.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Nagabhushana Netagunte <nagabhushana.netagunte@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Make use of GPIO framework and avoid the following build error:
tx25.c: In function 'tx25_fec_init':
tx25.c:73: error: dereferencing pointer to incomplete type
tx25.c:74: error: dereferencing pointer to incomplete type
tx25.c:75: error: dereferencing pointer to incomplete type
tx25.c:76: error: dereferencing pointer to incomplete type
tx25.c:83: error: dereferencing pointer to incomplete type
tx25.c:84: error: dereferencing pointer to incomplete type
tx25.c:114: error: dereferencing pointer to incomplete type
tx25.c:115: error: dereferencing pointer to incomplete type
tx25.c:116: error: dereferencing pointer to incomplete type
tx25.c:117: error: dereferencing pointer to incomplete type
tx25.c:124: error: dereferencing pointer to incomplete type
tx25.c:125: error: dereferencing pointer to incomplete type
tx25.c:126: error: dereferencing pointer to incomplete type
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
This patch fixes the warning dure to recent changes to the board
configuration:
cmd_i2c.o cmd_i2c.c -c
cmd_i2c.c:109:1: warning: missing braces around initializer
cmd_i2c.c:109:1: warning: (near initialization for 'i2c_no_probes[0]')
Signed-off-by: Sanjeev Premi <premi@ti.com>
Cc: Jason Kridner <jkridner@beagleboard.org>
Acked-by: Jason Kridner <jdk@ti.com>
Fix these:
cm4008.c: In function 'board_eth_init':
cm4008.c:79: warning: implicit declaration of function 'ks8695_eth_initialize'
cm41xx.c: In function 'board_eth_init':
cm41xx.c:79: warning: implicit declaration of function 'ks8695_eth_initialize'
While we are at it, sort include list in netdev.h
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Greg Ungerer <greg.ungerer@opengear.com>
Commit 21726a7 "Add assert() for debug assertions" caused build
warnings for many systems:
In file included from bedbug.c:6:
/home/wd/git/u-boot/work/include/bedbug/bedbug.h:24:1: warning: "assert" redefined
In file included from bedbug.c:3:
/home/wd/git/u-boot/work/include/common.h:144:1: warning: this is the location of the previous definition
In file included from cmd_bedbug.c:10:
/home/wd/git/u-boot/work/include/bedbug/bedbug.h:24:1: warning: "assert" redefined
In file included from cmd_bedbug.c:5:
/home/wd/git/u-boot/work/include/common.h:144:1: warning: this is the location of the previous definition
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
The OpenGear boards CM4008, CM4116 and CM4148 need their DRAM base
and RAM stack base addresses defined.
Fixes:
board.c: In function ‘__dram_init_banksize’:
board.c:227: error: ‘CONFIG_SYS_SDRAM_BASE’ undeclared (first use in this function)
board.c:227: error: (Each undeclared identifier is reported only once
board.c:227: error: for each function it appears in.)
board.c: In function ‘board_init_f’:
board.c:270: error: ‘CONFIG_SYS_INIT_SP_ADDR’ undeclared (first use in this function)
board.c:303: error: ‘CONFIG_SYS_SDRAM_BASE’ undeclared (first use in this function)
Signed-off-by: Greg Ungerer <greg.ungerer@opengear.com>
assert() is like BUG_ON() but compiles to nothing unless DEBUG is defined.
This is useful when a condition is an error but a board reset is unlikely
to fix it, so it is better to soldier on in hope. Assertion failures should
be caught during development/test.
It turns out that assert() is defined separately in a few places in U-Boot
with various meanings. This patch cleans up some of these.
Build errors exposed by this change (and defining DEBUG) are also fixed in
this patch.
Signed-off-by: Simon Glass <sjg@chromium.org>
Currently when you call ROUND with a value that is already a
multiple of the second parameter it will return a value that is
one multiple larger, instead of returning the value passed in.
There are only two types of usage of ROUND currently, one in
various config files to round CONFIG_SYS_MALLOC_LEN to a multiple
of 4096 bytes. The other in cmd_sf.c where the incorrect behavior
of ROUND is worked around be subtracting one from the length argument
before passing it to ROUND.
This patch fixes ROUND and removes the workaround from cmd_sf. It
also results in all of the malloc pools that use ROUND to compute
their size shrinking by 4KB.
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
The Lattice code was missed by commit e6a857d "fpga: constify to fix
build warning" resulting in such warnings:
fpga.c: In function 'fpga_load':
fpga.c:238: warning: passing argument 2 of 'lattice_load' discards qualifiers from pointer target type
fpga.c: In function 'fpga_dump':
fpga.c:278: warning: passing argument 2 of 'lattice_dump' discards qualifiers from pointer target type
Signed-off-by: Wolfgang Denk <wd@denx.de>
cc: Stefano Babic <sbabic@denx.de>
* 'master' of git://git.denx.de/u-boot-coldfire:
ColdFire:Clean up the CONFIG_STANDALONE_LOAD_ADDR usage
ColdFire:Add mb for 5253 dram initialization
ColdFire:Define the DM9000 byteswap for M5253 board.
ColdFire:Update the env settings for several boards.
ColdFire:disable the NFS define for 52277 board.
ColdFire:Update the timer_init since it was unified.
ColdFire: Cleanup for partial linking and --gc-sections
ColdFire: Update compile flags for each CPUs
ColdFire:Fix the configuration broken for some boards.
The M5253DEMO board swapped the io pins which make
the standard IO function did not work for dm9000.
Define the byte swap to use raw io for dm9000.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Move the environment outside the u-boot for some boards
and enlarge the u-boot size in some env settings.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
There is no network device on ColdFire 52277EVB board.But the default
cmd include NFS define which make the build error.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
* Improved boot env var setting
* Made room for a 64MB ramdisk by moving from 0x81600000 to 0x81000000
* Added ramarg, ramroot and ramboot env variables
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
buddy and camera are used to configure peripherals in the kernel at boot
time that cannot easily be detected by the kernel.
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Utilize the alternate mtest and define a valid region.
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
