Convert the board to support the video driver model, add the device
tree node, and remove the unnecessary code.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Convert the board to support the video driver model, add the device
tree node, and remove the unnecessary code.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Convert the board to support the video driver model, add the device
tree node, and remove the unnecessary code.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Convert the board to support the video driver model, add the device
tree node, and remove the unnecessary code.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Convert the board to support the video driver model, add the device
tree node, and remove the unnecessary code.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_MVNETA
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
CONFIG_NAND_DENALI select's CONFIG_SYS_NAND_SELF_INIT, so the
NAND initialization process is driven by the driver itself.
CONFIG_SYS_NAND_MAX_CHIPS and CONFIG_SYS_NAND_BASE are unused.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Current u-boot disables IFC support for SD boot on all ls1043a
boards. Actually IFC only conflicts with QSPI on ls1043a hardware.
Only when QSPI is used, IFC should be disabled. Otherwise,
the u-boot with ls1043aqds_sdcard_ifc_defconfig would not work.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
For most of ls2080ardb use-cases, mc private DRAM block is required
to be of 1.75GB.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
[YS: this reservation needs to be reduced if memory is not enough]
Reviewed-by: York Sun <york.sun@nxp.com>
As per updated board design, different QSPI flash
is connected on boards, hence change QSPI flash type
from Micron n25q512a device to spansion s25fs512s
device in dts and config.
Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
CONFIG_DISPLAY_BOARDINFO_LATE config is used to delay
the prints of boardinfo late in cycle during uboot boot.
This feature is not required in case of QSPI_BOOT.
Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch adds support for stm32h7 soc family, stm32h743
discovery and evaluation boards.
For more information about STM32H7 series, please visit:
http://www.st.com/en/microcontrollers/stm32h7-series.html
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Enable USB Host Networking support by enabling Ethernet/USB
adaptors support and by enabling some BOOTP flags
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Define i2c mux configuration. Add new vpd_reader which is used to read
vital product data. Read VPD from EEPROM and set eth0 MAC address.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Jose Alarcon <jose.alarcon@ge.com>
Add the ENV_MEM_LAYOUT_SETTINGS to CONFIG_EXTRA_ENV_SETTINGS
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This patch adds support for Vyasa RK3288 initial board
from Amarula Solutions.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This patch adds USB configs to support the USB OTG port(consist
of DWC2 controller) and the USB Host port(consist of EHCI and OHCI
controllers) on evb-rv1108 board, and also support fastboot over
USB and USB mass storage.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This adds support to Intel Cherry Hill board, a board based on
Intel Braswell SoC. The following devices are validated:
- serial port as the serial console
- on-board Realtek 8169 ethernet controller
- SATA AHCI controller
- EMMC/SDHC controller
- USB 3.0 xHCI controller
- PCIe x1 slot with a graphics card
- ICH SPI controller with an 8MB Macronix SPI flash
- Integrated graphics device as the video console
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
To remove the assignment of CONFIG_SYS_EXTRA_OPTIONS option,
which is deprecated, use the CONFIG_XXXX_BOOT options to
indicate the boot media, and the SoC is selected by the board.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
As said in READRE.kconfig, include/configs/*.h will be removed
after all options are switched to Kconfig. As the first step,
remove the follow line from include/configs/*.h.
#include <asm/hardware.h>
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
The SAMA5D27-SiP (System in Package) integrates the SAMA5D2
with 1Gbit DDR2-SDRAM in a single package.
The SAMA5D27 SOM1 embeds a 64Mbit QSPI flash, KSZ8081 Phy and
Mac-address EEPROM.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Because before switching to a lower clock source, we must switch
the clock source first instead of last. So before configuring the
PMC_MCKR register, invoke at91_mck_init_down() first.
As said in datasheet, the the size of SPL must not exceed the maximum
size allowed(64Kbytes).
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_EMIF4
CONFIG_SDRC
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefano Babic <sbabic@denx.de>
In mancy cases both CONFIG_ENV_OFFSET and CONFIG_ENV_ADDR point
to an otherwise-unused SMNAND_ENV_OFFSET.
This patch will set both CONFIG_ENV_OFFSET and CONFIG_ENV_ADDR to
whatever value was defined by SMNAND_ENV_OFFSET.
Signed-off-by: Adam Ford <aford173@gmail.com>
Much of the AM3517 functions are copies of the standard definitions
used in ti_omap3_common.h. Moving to include a common file
reduces the amount of duplicative code and clutter. A few
AM3517 specific functions (like EMIF4) are explictly defined
and a few items are undefined or redefined, but overall the number
of lines of code shink.
Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Derald D. Woods <woods.technical@gmail.com>
The PMMC firmware should be bundled with the FIT image for HS devices,
remove the steps that load and install this firmware outside of FIT.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Add the code to set the ethernet mac address from eeprom by using
the common code from the common folder.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Replace the code to set the ethernet mac address with the code from
the common folder.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch add support of LS1088AQDS platform.
The LS1088A QorIQTM Development System (QDS) is a high-performance
computing, evaluation, and development platform that supports the
LS1088A QorIQ Architecture processor.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
LS1088A is an ARMv8 implementation. The LS1088ARDB is an evaluatoin
platform that supports the LS1088A family SoCs. This patch add basic
support of the platform.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
[YS: Disabled NAND in board header file]
Reviewed-by: York Sun <york.sun@nxp.com>
WIP: disable NAND for LS1088ARDB
MX6Q/QP IPU operates at 264MHz and MX6DL IPU at 198MHz.
When running a SPL target, which supports multiple MX6 variants we cannot
properly setup the IPU clock frequency via CONFIG_IPUV3_CLK option as
such decision is done in build-time currently.
Remove the CONFIG_IPUV3_CLK option and let the IPU clock frequency be
configured in run-time on mx6.
Reported-by: Eric Nelson <eric@nelint.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Eric Nelson <eric@nelint.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
[agust: fixed #endif in cgtqmx6eval.h]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
This migrates ASIX, ASIX88179, MCS7830, RTL8152 and SMSC95XX to Kconfig.
Update defconfigs.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
CONFIG_USB_HOST_ETHER is the framework that the drivers are dependent on
USB_HOST_ETHER. Use this as a menu and move the existing LAN75XX and
LAN78XX options under new menu. Finally update the defconfigs that need
CONFIG_USB_HOST_ETHER.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
- Pass MTDPARTS kernel arguments to kernel
- Use Kconfig CONFIG_NAND instead of CONFIG_SYS_EXTRA_OPTIONS="NAND"
- Call 'usb_stop' on kernel start
- Update Falcon mode setup to match other OMAP3 boards
- Use "uEnv.txt" as boot script instead of "boot.scr"
This commit removes definitions of CONFIG_SYS_BARGSIZE defined to be
equal to CONFIG_SYS_CBSIZE in numerous configuration files.
We remove such definitions in two situations:
- CONFIG_SYS_CBSIZE is otherwise not defined in the board
configuration file, which means the default value of
CONFIG_SYS_CBSIZE == 256 applies. In this case, the default value
of CONFIG_SYS_BARGSIZE == 512 (common/image.c) is suitable, as it is
larger.
- CONFIG_SYS_CBSIZE is defined in the board configuration file, but
to a value equal or less than 512. In this case, the default value
of CONFIG_SYS_BARGSIZE == 512 (common.image.c) is suitable, as it
is equal or larger.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
CONFIG_SYS_BARGSIZE is already defined to 512 in common/image.c when
not defined. Therefore, there is no point in having board
configuration files define it to 512.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Now that include/config_fallbacks.h define a sane fallback for
CONFIG_SYS_MAXARGS, we can drop the definition of this constant in all
configurations that were using the default value.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Now that the fallback value of CONFIG_SYS_PBSIZE in
include/config_fallbacks.h has been adjusted, remove its definition
from a large number of board configuration files.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Now that include/config_fallbacks.h define a sane fallback for
CONFIG_SYS_CBSIZE, we can drop the definition of this constant in all
configurations that were using the default value.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Drop <config.h> from stih410-b2260.h]
Signed-off-by: Tom Rini <trini@konsulko.com>
