This adds a new SPI flash command which only rewrites blocks if the contents
need to change. This can speed up SPI flash programming when much of the
data is unchanged from what is already there.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Since commit d388298a59 by
Stefano Babic this file is no longer needed so delete it.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Loïc Minier <loic.minier@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This reverts commit 041c542219.
The lines removed by this commit weren't redundant. The logic is (and
probably should be better commented):
Find the intersection of the advertised capabilities of both sides of
the link (lpa).
From that intersection, find the highest capability we can run at
(that will be the negotiated link).
Now imagine that the intersection (lpa) is (LPA_100HALF | LPA_10FULL).
The code will now set phydev->speed to 100, and phydev->duplex to 1,
but this link does not support 100FULL.
Kudos to Andy Fleming <afleming@gmail.com> for binging this to
attention and for the explanation.
Signed-off-by: Wolfgang Denk <wd@denx.de>
This is a trivial fix in the documentation, which corrects
board_init_r() source reference.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
The MAC address stored in the inventory eeprom begins at offset 1.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Wolfgang Denk <wd@denx.de>
On some systems, we get a warning when %lu is used with size_t's, so
use the correct format string.
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The new sanity check introduces a printf warning for some systems:
eth.c:233: warning: format '%zu' expects type 'size_t', but argument 3 has type 'int'
Rather than tweak the format string, use the new assert() helper instead.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Recent commit a4814a69d3 cleaned up generation of
asm-offsets.s for SoC dirs, but missed adding it to the ignore
list which makes it show up in `git status`.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
There is no code anywhere that references BOOTFLAG_* so remove these
defines.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Valentin Longchamp <valentin.longchamp@keymile.com>
Cc: Peter Tyser <ptyser@xes-inc.com>
Commit 093498669 (Put common autoload code into auto_load() function)
broke handling of autoload environment variable not being set.
The bootp/dhcp code will just keep on requesting IP address forever
and never start TFTP download.
Fix it by moving TftpStart() outside the conditional like it was before.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Simon Glass <sjg@chromium.org>
Flush the dcache before removing the TLB with caches enabled.
Otherwise this might lead to problems later on, e.g. while booting
Linux (as seen on ICON-440SPe).
Signed-off-by: Stefan Roese <sr@denx.de>
Change bd_t->bi_phy* arrays from 1 to 2 for PPC405EX since
405EX has 2 ethernet interfaces.
Signed-off-by: Bernhard Weirich <bernhard.weirich@riedel.net>
Signed-off-by: Stefan Roese <sr@denx.de>
Result of running the following command to address Wolfgang's
comment about camel case:
for file in `find . | grep '\.[chS]$'`; do perl -i -pe
's/(green|yellow|red|blue)_LED_(on|off)/$1_led_$2/g' $file; done
Discussion:
http://patchwork.ozlabs.org/patch/84988/
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
omap4: fix pad configuration settings for SDP and Panda
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sebastien Jan <s-jan@ti.com>
Signed-off-by: David Anders <x0132446@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Tuning some IO settings for better performance and power.
And consolidate all such IO settings at one place.
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
SDRAM init was not working on ES1.0 due to a programming
error. A pointer that was passed by value to a function
was set in function emif_get_device_details(), but the effect
wouldn't be seen in the calling function. The issue came
out while testing for ES1.0 because ES1.0 doesn't have any
SDRAM chips connected to CS1
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Factor out common parts from omap4_sdp4430.h and omap4_panda.h
into a new file omap4_common.h
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch contains the generic changes required after
change to generic API in the previous patch.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Convert all OMAP specific functions to use the common API
definitions in include/asm/gpio.h. In the process, made
few additional changes:
- Use -EINVAL consistently. -1 was used in many places.
- Removed one-liner static functions that were used only
once. Replaced the content as necessary.
- Combines implementation of functions omap_get_gpio_dataout()
and omap_get_gpio_datain(). To do so, new static function
_get_gpio_direction() was added.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Modify the MEMTEST start and end address. The memtest range was overlapping the
CONFIG_SYS_LOAD_ADDR which causes the uImage to be corrupt.Also, modify the
size for which mtest is run to 32MB from 16MB.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Nagabhushana Netagunte <nagabhushana.netagunte@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Enable SPI flash boot mode in configuration file as default.
With the introduction of 456MHz part, SPI operating frequency
will increase and at this frequency SPI does not work correctly.
Hence reduce the default SPI speed to 30MHz from 50MHz.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Nagabhushana Netagunte <nagabhushana.netagunte@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Modify U-boot promt string from 'DA830-evm >' to 'U-Boot >' as
there are many variants of da830 based boards which have diffrent
names such as L137, AM1707 etc.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Nagabhushana Netagunte <nagabhushana.netagunte@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
OMAP3: Add 37xx ESx revision numbers.
Signed-off-by: Michael Jones <michael.jones@matrix-vision.de>
Signed-off-by: Howard D. Gray <howard.gray@matrix-vision.de>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This allows the EEPROM layer to send a single i2c write command
per page, and wait CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS between
i2c write commands.
Signed-off-by: Michael Jones <michael.jones@matrix-vision.de>
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Read directly from OMAP_GPIO_DATAOUT to get the output state of the GPIO pin
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Make use of GPIO framework and avoid the following build error:
tx25.c: In function 'tx25_fec_init':
tx25.c:73: error: dereferencing pointer to incomplete type
tx25.c:74: error: dereferencing pointer to incomplete type
tx25.c:75: error: dereferencing pointer to incomplete type
tx25.c:76: error: dereferencing pointer to incomplete type
tx25.c:83: error: dereferencing pointer to incomplete type
tx25.c:84: error: dereferencing pointer to incomplete type
tx25.c:114: error: dereferencing pointer to incomplete type
tx25.c:115: error: dereferencing pointer to incomplete type
tx25.c:116: error: dereferencing pointer to incomplete type
tx25.c:117: error: dereferencing pointer to incomplete type
tx25.c:124: error: dereferencing pointer to incomplete type
tx25.c:125: error: dereferencing pointer to incomplete type
tx25.c:126: error: dereferencing pointer to incomplete type
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
This patch fixes the warning dure to recent changes to the board
configuration:
cmd_i2c.o cmd_i2c.c -c
cmd_i2c.c:109:1: warning: missing braces around initializer
cmd_i2c.c:109:1: warning: (near initialization for 'i2c_no_probes[0]')
Signed-off-by: Sanjeev Premi <premi@ti.com>
Cc: Jason Kridner <jkridner@beagleboard.org>
Acked-by: Jason Kridner <jdk@ti.com>
Fix build problem:
nand_spl/board/davinci/da8xxevm/hawkboard_nand_spl.c: In function 'board_init_f':
nand_spl/board/davinci/da8xxevm/hawkboard_nand_spl.c:132: warning: implicit declaration of function 'nand_boot'
nand_spl/board/davinci/da8xxevm/hawkboard_nand_spl.c:133: warning: 'noreturn' function does return
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Syed Mohammed Khasim <sm.khasim@gmail.com>
Cc: Sughosh Ganu <urwithsughosh@gmail.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Fix these:
cm4008.c: In function 'board_eth_init':
cm4008.c:79: warning: implicit declaration of function 'ks8695_eth_initialize'
cm41xx.c: In function 'board_eth_init':
cm41xx.c:79: warning: implicit declaration of function 'ks8695_eth_initialize'
While we are at it, sort include list in netdev.h
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Greg Ungerer <greg.ungerer@opengear.com>
Commit 21726a7 "Add assert() for debug assertions" caused build
warnings for all tegra2 based boards:
clock.c:36:1: warning: "assert" redefined
In file included from clock.c:29:
include/common.h:144:1: warning: this is the location of the previous definition
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
The pointer to the flash based bootargs should be a "char *", not unsigned.
Fixes:
cm41xx.c: In function ‘env_flash_cmdline’:
cm41xx.c:67: warning: pointer targets in passing argument 2 of ‘setenv’ differ in signedness
Signed-off-by: Greg Ungerer <greg.ungerer@opengear.com>
The pointer to the flash based bootargs should be a "char *", not unsigned.
Fixes:
cm4008.c: In function ‘env_flash_cmdline’:
cm4008.c:67: warning: pointer targets in passing argument 2 of ‘setenv’ differ in signedness
Signed-off-by: Greg Ungerer <greg.ungerer@opengear.com>
