Commit graph

22 commits

Author SHA1 Message Date
Michal Simek
ce90654d1c xilinx: Sync DTs with Linux kernel
There are several changes which happen in mainline kernel which should get
also to U-Boot. Here is the list of patches from the kernel:

- ARM: zynq: Fix leds subnode name for zc702/zybo-z7
- arm64: dts: zynqmp: Fix leds subnode name for zcu100/ultra96 v1
- arm64: dts: zynqmp: Fix u48 si5382 chip on zcu111
- arm64: dts: zynqmp: Wire up the DisplayPort subsystem
- arm64: dts: zynqmp: Add DisplayPort subsystem
- arm64: dts: zynqmp: Add DPDMA node
- arm64: dts: zynqmp: Enable phy driver for Sata on zcu102/zcu104/zcu106
- arm64: dts: zynqmp: Enable si5341 driver for zcu102/106/111
- arm64: dts: zynqmp: Add DT description for si5328 for zcu102/zcu106
- arm64: dts: zynqmp-zcu100-revC: correct interrupt flags
- arm64: dts: xilinx: align GPIO hog names with dtschema
- arm64: zynqmp: Add Xilinx AES node
- dt: bindings: dma: xilinx: dpdma: DT bindings for Xilinx DPDMA

but also some other changes have been done.
- Using only one compatible string for adxl345 on zturn
- Remove Xilinx internal DP bindings
- Remove USB3.0 serdes configurations
- Remove SATA serdes configuration for zc1232
- Resort nvmem_firmware
- Update nand compatible string
- Aling power-domains property for sd0/1

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-03-30 12:03:24 +02:00
Michal Simek
01a6da1661 xilinx: Fix xlnx,mio_bank property
s/xlnx,mio_bank/xlnx,mio-bank/g

DT binding is describing mio-bank not mio_bank that's why fix all DTSes and
also driver itself.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
2020-08-20 09:49:20 +02:00
Michal Simek
14c0fbbc94 arm64: zynqmp: Fix irps5401 device nodes
- Do not use irps54012 as device node which is not correct.
- Fix addresses of irps5401/u180 on zcu104 revisions.
- Remove clock-cells property. It is PMIC without any clock output.
- Define irps5401 nodes in zynqmp-e-a2197

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-04-27 14:21:18 +02:00
Michal Simek
5df63a60aa arm64: zynqmp: Fix addresses in partition definitions
Node name should be <name>@<address> which is not how partitions are
described.

Issue was found by running dtbs_check as:
flash@0: 'partition@qspi-device-tree', 'partition@qspi-fsbl-uboot',
'partition@qspi-linux', 'partition@qspi-rootfs'
do not match any of the regexes: ...

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-04-06 12:51:31 +02:00
Manish Narani
12ffe75819 arm64: zynqmp: Add 'no-1-8-v' property for ZynqMP Boards
Modify dts files to add 'no-1-8-v' property for all the ZynqMP boards.
User can remove this property to enable the UHS mode. This is to keep
the same speed (HS) modes across all the stages of the Linux Boot. Due
to power cycling limitation of some of the ZynqMP boards, some SD cards
don't get power cycled and are failing in Linux.

Signed-off-by: Manish Narani <manish.narani@xilinx.com>
2020-04-06 12:51:31 +02:00
Michal Simek
d31f1c9236 arm64: zynqmp: Update Copyright years to 2020
Trivial change.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-04-06 12:51:31 +02:00
Sudeep Holla
ad967af6bd arm64: dts: zynqmp: replace gpio-key,wakeup with wakeup-source property
Most of the legacy "gpio-key,wakeup" boolean property is already
replaced with "wakeup-source". However few occurrences of old property
has popped up again, probably from the remnants in downstream trees.

This patch replaces the legacy properties with the unified
"wakeup-source" property introduced by:
"Input: gpio_keys - switch to using generic device properties"
(sha1: 700a38b27eefc582099fdf69effacfad0ad738a4)

Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-01-14 09:05:56 +01:00
Michal Simek
096d7f5b3e arm64: dts: zynqmp: Fix node names which contain "_"
s/_/-/ for node names.

It fixes warnings like this:
... Warning (node_name_chars_strict): /cpu_opp_table:
Character '_' not recommended in node name ...

Issues reported by make dtbs W=12

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-01-14 09:05:55 +01:00
T Karthik Reddy
166fb46ad3 zynqmp: dts: Cleanup no-1-8-v property from sdhci dt nodes
Removed no-1-8-v property from zynqmp sdhci devicetree nodes to
allow UHS-I capable SD cards to work in SD3.0 UHS modes.

Boards that does not have level shifter for SD, does not support 1.8v.
so no-1-8-v property to sdhci dt nodes should be present in zcu102 Rev-A,B,
zcu104 Rev-A,C, zcu100, zcu1275 Rev-B boards.

Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-01-14 09:05:55 +01:00
Harini Katakam
631d9a9981 arm64: zynqmp: dt: Add missing DP83867 quirk
The DP83867 strap control workaround is already present in Linux kernel
mainline binding. All these Xilinx boards require this quirk.

Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-24 13:37:02 +02:00
Venkatesh Yadav Abbarapu
7e2bf38768 arm64: zynqmp: Fix the si570 clock frequency on zcu111
The si570 clock frequency should be 156.25MHz as per datasheet.

Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-24 13:37:02 +02:00
Michal Simek
b02ea93137 arm64: zynqmp: Add label property to all ina226 on zcu111
Label property is adding capability to distiguish chips from each other
when iio framework is used.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-24 13:37:02 +02:00
Michal Simek
65c4c3773b arm64: zynqmp: Enable iio-hwmon for ina226 on zcu111
ina226 hwmon driver is deprecated and it is recommended to use new iio
based driver. The patch is enabling iio-hwmon driver to export
functionality from IIO to hwmon interface to be able to use lm-sensors
package.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-24 13:37:01 +02:00
Michal Simek
2975a42b42 arm64: zynqmp: Use ethernet-phy as node name for ethernet phys
Ethernet phys based on devicetree specification should be using
ethernet-phy@ node name instead of pure phy@.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-24 13:37:01 +02:00
Neil Armstrong
ffd4c7c2ec dts: switch spi-flash to jedec, spi-nor compatible
There is no reason not to use the Linux "jedec,spi-nor" binding in U-Boot
dts files. This compatible has been added in sf_probe, let use it.

This patch switches to jedec,spi-nor when spi-flash is used in the DTS
and DTSI files, and removed spi-flash when jedec,spi-nor is already
present.

The x86 dts are switched in a separate commit since it depends on a change
in fdtdec.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Evgeniy Paltsev <paltsev@synopsys.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Patrick Delaunay <Patrick.delaunay@st.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2019-04-12 10:54:27 +05:30
Michal Simek
1317a5e5ea arm64: zynqmp: Remove autodetected devices without description
It will never reach mainline that's why remove it.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-02-15 15:04:01 +01:00
Michal Simek
8bdad43333 arm64: zynqmp: Switch all platforms to DM_I2C
CONFIG_PCA953X is not needed because of PCA953X is integrated in gpio
subsystem already. That's why also remove CMD_PCA953X which is only for
this driver.

zcu102/zcu104-revC/zcu106/zcu111 contain links to eeprom which stores MAC address.

DM_I2C is not enabled for the whole SoC because it increase size for
mini configurations and there is no I2C symbol present to setup
dependencies.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
2019-02-14 14:31:10 +01:00
Michal Simek
6bd13ee94e arm64: zynqmp: Setup clock-output-names for si570 chips
If there are more instances of si570 clock-output-names property
should be used for differentiation of clock output.
The patch is adding this optional properties for all zynqmp boards with
si570 chip.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-11-29 10:30:02 +01:00
Michal Simek
0ed45f0025 arm64: zynqmp: Wire spi-flash compatible string with flashes
Enable reading tx and rx buswidth from DT via spi-uclass.
To get these from uclass spi-flash compatible string has to be added
to flash node.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-11-29 10:30:02 +01:00
Michal Simek
3c1eaec012 arm: zynq: Drop #address-cells and #size-cells from gpio-keys
dtc is showing some warnings and this change was also done in
the Linux kernel as "Input: gpio-keys - clean up device tree binding
example"
with this fragment in commit message
"Drop #address-cells and #size-cells, which are not required by the
gpio-keys binding documentation, as button sub-nodes are not devices."

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-06-15 08:06:31 +02:00
Michal Simek
f0d56145d9 arm64: zynqmp: Disable WP on zcu111
On this board there is SD slot without WP connected.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-05-31 13:50:39 +02:00
Michal Simek
f190eaf002 arm64: zynqmp: Add support for Xilinx zcu111-revA
Xilinx zcu111 is a customer board. It is reusing some parts from zcu102.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09 12:14:53 +02:00