dwc3-generic has been broken since MISC uclass has been modified to scan DT
sub-nodes after bind.
Fixing it by a using the no-op uclass.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This uclass is intended for devices that do not need any features from the
uclass, including binding children.
This will typically be used by devices that are used to bind child devices
but do not use dm_scan_fdt_dev() to do it. That is for example the case of
several USB wrappers that have 2 child devices (1 for device and 1 for
host) but bind only one at a any given time.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The EHCI iMX6 driver is only partly converted to DT probing and
still uses a tremendous amount of hard-coded addresses. Worse,
the driver uses hard-coded SoC-model-specific base addresses, which
are derived from values protected by SoC-specific macros, hence the
driver is also compiled for a specific SoC model. Even worse, the
driver depends on specific sequential indexing of the controllers,
from which it derives offsets in the PHY and ANATOP register sets.
However, when the driver is probed from DT, the indexing is not
correct. In fact, each controller has index 0. This patch derives
the index for DT probing case from the controller base addresses,
which is not the way this should be done, however it is the least
intrusive approach, favorable this close to release.
The necessary steps to convert this driver fully to DT probing are
described inside the patch, however this should be done in the next
release and depends on iMX clock driver patches.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Abel Vesa <abel.vesa@nxp.com>
Cc: Adam Ford <aford173@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Ludwig Zenz <lzenz@dh-electronics.com>
Cc: Lukasz Majewski <lukma@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Vagrant Cascadian <vagrant@debian.org>
After the conversion to DM the U-Boot proper binary name
is 'u-boot-dtb.img', so adjust it accordingly.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
After the transition to DM, only the mx6dl/solo wandboard
is supported.
Add FIT image support so that all the wandboard variants
can be supported, like it was prior to the DM conversion.
Successfully booted Linux on mx6q/solo/qp wandboards.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Place dtbs under SoC level rather than board level.
imx6q-novena.dtb and imx6dl-wandboard-revb1.dtb were
placed under the board config option, so move them
to SoC level.
This also aligns with the kernel dts Makefile format.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
The raw u-boot.bin for tinker board has been about 450KB without
debug option, and 550KB with all debug on, and the default value is 200KB,
which is not enough for run raw u-boot.bin.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
We need to update TEXT BASE for TPL/SPL/U-Boot;
SPL no need relocate STACK after enable TPL, so remove it;
Don't enable pinctrl names so that SPL can get pinctrl dts;
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
rockchip pinctrl driver has update to use dts, so we need
to add the pinctrl config in SPL for sdmmc.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Migrate all the "u-boot,dm-pre-reloc" tag from rk3288-tinker.dts
into rk3288-tinker-u-boot.dtsi.
When both board level and soc level '-u-boot.dtsi' files exist,
we need to include the soc level 'rk3288-u-boot.dtsi' manually.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
TPL is at SRAM while other stage is at SDRAM, so it needs
separate STACK.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
More boards other than vyasa needs TPL, so enable the TPL configs
at chip level instead of board level.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
The pointer to struct atf_image_info in
bl31_params_mem.bl31_params.bl31_image_info is not initialized before
being dereferenced. This can cause U-Boot to crash right before jumping
to the BL31 ATF binary.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Fixes: bcc1726a7b ("spl: add support to booting with ATF")
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
There is a regression seen on Poplar platform, which doesn't even show
a U-Boot version banner on booting. It turns out that due to landing
of commit 3a7c45f6a7 ("simple-bus: add DM_FLAG_PRE_RELOC flag to
simple-bus driver"), we need to increase SYS_MALLOC_F_LEN from its
default size 0x400, as pre-relocation requires more memory there. Let's
increase SYS_MALLOC_F_LEN to 0x4000 to fix the regression.
Thanks to Andreas Färber <afaerber@suse.de> for reporting, and Bin Meng
<bmeng.cn@gmail.com> for trouble shooting.
Reported-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Andreas Färber <afaerber@suse.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdGaVcAAoJEB6zHgIOrC/Ic1oH/3Hu55HbHVnA2QqRof/o6RnZ
VNJQ11+Zs7QA7TIMT/Z5j9ohX0pEkVPQziD9zAL1rz7WJ/laYkPh8wqsKWmfFD2j
2mCCnf8/vGvST8fiSv0BQ6cqozdMwdQjQ08Eqw0srJhCzqj/I8o8MNlts+OAXNIM
CyT7LdIr/QSO05zDYxFibki4qs7Q5S8WXbtjsmbAAYajcet5w5+hEZRAD2YXuUv8
TBuBWz6bgcSLbV7E7YXexoffgIha2K3ETAxWraKZLcc96MNLL054uBraa3dmybqZ
+0+PHIOcNk2JR4BQmUHCoNgEuKTBPlayxZ3hVUzWzUwot4gBRRUFu/pbnRtLcF4=
=RzN7
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-fixes-2019.07-b' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
Second set of u-boot-atmel fixes for 2019.07 cycle
The definition of an unimplemented function is corrected.
-----BEGIN PGP SIGNATURE-----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=P/ys
-----END PGP SIGNATURE-----
Merge tag 'efi-2019-07-rc5-4' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for v2019.07-rc5 (4)
The definition of an unimplemented function is corrected.
Move the sg_set_pinsel macro to arch/arm/mach-uniphier/arm32/debug_ll.S
since it is not used anywhere else.
Move the C functions sg_set_{pinsel,iectrl} to debug-uart.c since they
are not used anywhere else.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
debug_uart_init() is called from spl_board_init(), which is only
compiled for SPL. For U-boot proper, _debug_uart_init() is unreachable,
so dropped by the dead code elimination.
Now that 64-bit SoCs of this SoC family no longer support SPL,
debug-uart-ld20.c is never compiled.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This file calls readl(), so needs to include <linux/io.h>.
Currently, it relies on someone else including it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
ConvertPointer() must be EFIAPI. The first parameter should be of type
efi_uint_t. Use the same parameter name as the UEFI specification.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The MPU region dedicated for SDRAM for STM32F4 SoCs family
was set to 16MB, but STM32F429 Evaluation board have 32MB of SDRAM.
When kernel starts, only first 16MB of SDRAM are configured with XN
(eXecute Never) bit disabled, whereas kernel is using 32MB.
To avoid such situation in the future, extend this MPU region to 512MB
as for STM32F7/H7.
It fixes the following user land exception on STM32F429 Evaluation
board :
[ 1.713002] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
[ 1.722605] devtmpfs: mounted
[ 1.733057] Freeing unused kernel memory: 72K
[ 1.737622] This architecture does not have kernel memory protection.
[ 1.744070] Run /sbin/init as init process
[ 1.906850]
[ 1.906850] Unhandled exception: IPSR = 00000004 LR = fffffffd
[ 1.914282] CPU: 0 PID: 1 Comm: init Not tainted 5.1.0-00002-gcf9ca5719954 #6
[ 1.921433] Hardware name: STM32 (Device Tree Support)
[ 1.926601] PC is at 0x1a00b64
[ 1.929642] LR is at (null)
[ 1.932669] pc : [<01a00b64>] lr : [<00000000>] psr: 01000000
[ 1.938993] sp : 01a5cfb0 ip : 00000000 fp : 00000000
[ 1.944269] r10: 01a43b00 r9 : 00000000 r8 : 00000000
[ 1.949564] r7 : 00000000 r6 : 00000000 r5 : 00000000 r4 : 00000000
[ 1.956168] r3 : 00000000 r2 : 00000000 r1 : 00000000 r0 : 00000000
[ 1.962701] xPSR: 01000000
[ 1.965506] CPU: 0 PID: 1 Comm: init Not tainted 5.1.0-00002-gcf9ca5719954 #6
[ 1.972658] Hardware name: STM32 (Device Tree Support)
[ 1.978132] [<0000c009>] (unwind_backtrace) from [<0000b24f>] (show_stack+0xb/0xc)
[ 1.986024] [<0000b24f>] (show_stack) from [<0000b947>] (__invalid_entry+0x4b/0x4c)
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
As in stm32f7-u-boot.dtsi these nodes already have "u-bootdm-pre-reloc"
property, no need to add them again in stm32f746-disco-u-boot.dtsi.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Default value (4000ms) of PHY_ANEG_TIMEOUT for Micrel KSZ9031 contoller
isn't sufficient to finish auto-negotiation, which sometimes leads to
timeout errors:
Apalis iMX6 # dhcp
FEC Waiting for PHY auto negotiation to complete......... TIMEOUT !
Increase the auto-negotiation time-out to 15000ms.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Philippe Schenker <philippe.schenker@toradex.com>
Enable DM Video support on iMX53 M53Menlo and fix minor details
to restore previous behavior of the system.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Enable DM block and DM MMC and DM USB support on iMX53 M53Menlo .
Convert board code to match the DM support. This also enables DM
pincontrol to configure the SDHI pins.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Enable DM GPIO support on iMX53 M53Menlo and fix up board code where
applicable. Enable MALLOC_F to let the GPIO controllers bind early on.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Import iMX53 M53Menlo device tree from Linux next-20190607 3f310e51ceb1 .
Enable DT control in full U-Boot . Add U-Boot extras into separate DTSi,
the GPIO controllers need to be inited early, otherwise m53_set_clock()
won't be able to detect the correct CPU clock frequency by reading the
GPIO.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Synchronize iMX53 device tree from Linux next-20190607 3f310e51ceb1 ,
this is needed to get NFC, UART, USBOTG DT nodes.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Since the pico-pi uses the distroboot,
this commit remove the 'script' variable (cf boot_scripts).
Signed-off-by: Pierre-Jean Texier <pjtexier@koncepto.io>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
According to hab.c code we have to notify the ROM code if the MMU is
enabled or not. This is achieved by setting the "pu_irom_mmu_enabled"
to 0x1.
The current address in hab.c code is wrong for i.MX6SL, according to ROM
map file the correct address is 0x00901c60.
As we are writing in the wrong address the ROM code is not flushing the
caches when needed, and the following HAB event is observed in certain
scenarios:
--------- HAB Event 1 -----------------
event data:
0xdb 0x00 0x14 0x41 0x33 0x18 0xc0 0x00
0xca 0x00 0x0c 0x00 0x01 0xc5 0x00 0x00
0x00 0x00 0x07 0xe4
STS = HAB_FAILURE (0x33)
RSN = HAB_INV_SIGNATURE (0x18)
CTX = HAB_CTX_COMMAND (0xC0)
ENG = HAB_ENG_ANY (0x00)
Update MX6SL_PU_IROM_MMU_EN_VAR to address this issue.
Reported-by: Frank Zhang <frank.zhang@nxp.com>
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
After the conversion to DM the U-Boot binary is called u-boot-dtb.imx,
so fix the README file accordingly.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Joris Offouga <offougajoris@gmail.com>
