Commit graph

37 commits

Author SHA1 Message Date
Hans de Goede
aad2ac24c0 sunxi: video: Add support for tl059wv5c0 lcd panels
Add support for the 6" 480x800 tl059wv5c0 panel used on e.g. Utoo P66 and
Aigo M60/M608/M606 tablets.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-02-20 08:11:57 +01:00
Hans de Goede
242e3d893d sunxi: video: Add support for LCD reset pin
On some boards there is a gpio to reset the LCD panel, add support for this.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-02-20 08:11:57 +01:00
Hans de Goede
20779ec3a5 sunxi: video: Dynamically reserve framebuffer memory
Only use CONFIG_SUNXI_MAX_FB_SIZE to reserve memory at the top when relocating
u-boot, and calculate the actual amount of memory necessary when setting up
the video-mode and use only that, freeing up some additional memory for use
by the kernel.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-02-16 19:44:38 +01:00
Hans de Goede
5633a296eb sunxi: video: Do not use CONFIG_SYS_MEM_TOP_HIDE for the framebuffer
Do not use CONFIG_SYS_MEM_TOP_HIDE for the framebuffer, instead override
board_get_usable_ram_top to make sure that u-boot is not relocated into the
area where we want to use the framebuffer, and patch the devicetree from
sunxi_simplefb_setup() to tell the kernel to not touch the framebuffer.

This makes u-boot properly see the framebuffer as dram, and initalize the
level 2 cache for it, fixing the very slow cfb scrolling problem.

As an added bonus this stops us from reserving the framebuffer when simplefb
is not used because an older kernel is booted, or hdp is used and no hdmi
cable was plugged in, freeing up the memory for kernel use in these cases.

Reported-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-02-16 19:40:59 +01:00
Hans de Goede
fb75d972ea sunxi: video: Force h/vsync active high when using ext. vga dac on some boards
On both my A13-OLinuxIno and my A13-OLinuxIno-Micro, the vga output gives an
unstable image when active low v or hsync is used.

The problem seems to be specific to the OLinuxIno A13 (normal & micro)
boards. I've just looked up the schematics and they use an opendrain driver
for the vga sync lines, and with sync pulses it is the logical high->low
edge of the pulse which counts for the timing, which with an active low
sync is being driven by the pull-up, and that simply seems to not drive
it hard enough to get a stable image.

So force v and hsync active high on these boards. independent of what the
modeline says. This fixes the unstable image.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-02-02 13:57:16 +01:00
Hans de Goede
a7403ae84d sunxi: video: Make pwm polarity configurable
It turns out that there are some panels where the pwm input is not active low,
so make it configurable.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-23 15:15:02 +01:00
Hans de Goede
27515b20c1 sunxi: video: Add support for Hitachi tx18d42vm LVDS LCD panels
Add support for Hitachi tx18d42vm LVDS LCD panels, these panels have a
lcd controller which needs to be initialized over SPI, once that is
done they work like a regular LVDS panel.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-23 15:14:53 +01:00
Hans de Goede
7cd6f92d41 sunxi: video: Use frontend for dma on sun4i to fix memory bandwidth problems
Testing has shown that on sun4i the display backend engine does not have
deep enough fifo-s causing flickering / tearing in full-hd mode due to
fifo underruns. On sun4i use the display frontend engine to do the dma from
memory, as the frontend does have deep enough fifo-s.

As added advantage of this is that it results in much better memory bandwidth
as it reduces the amount of dram bank switches, for more details see:

http://ssvb.github.io/2014/11/11/revisiting-fullhd-x11-desktop-performance-of-the-allwinner-a10.html

Note that this changes the pipeline searched for in the simplefb node, we can
get away with doing this now, since no kernel has yet shipped with simplefb
dtb nodes, and I will make sure to get a simplefb node with the new pipeline
into 3.19 before it ships.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-22 12:34:56 +01:00
Siarhei Siamashka
97ece830ec video: sunxi: Hook up SSD2828 with the sunxi video driver
Convert GPIO names from Kconfig strings into pin numbers for
the 'ssd2828_config' struct. Add SSD2828 initialization between
enabling the parallel LCD interface and turning on the backlight.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-01-22 12:34:56 +01:00
Hans de Goede
6515032e3b sunxi: display: Make lcd display clk phase configurable
While running some tests with an Olinuxino-A13-Micro + a 7" Olimex LCD module
I noticed that the screen flickered. This is caused by the lcd display clk
phase reg value being set to 0, where it should be 1 in this setup.

This commit adds a Kconfig option for the lcd display clk phase, so that we
can set it per board. This defaults to 1, because looking at all the fex
files in sunxi-boards, that is by far the most used value.

This commit updated the Ippo and MSI Primo73 tablet defconfigs to override the
default of 1 with 0, as that is the correct value for those tablets, this
keeps the register settings the same as before this commit.

The Olinuxino-A13 defconfigs are not updated, changing the register setting
for these boards from 0 to 1, this is intentional.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-22 12:34:55 +01:00
Chen-Yu Tsai
507e27dfc9 sunxi: video: Add support for external DAC enable pin
The external DAC for VGA output might have either a power or reset
control pin that needs to be pulled up, as is the case on the
Hummingbird A31.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-01-14 14:56:40 +01:00
Hans de Goede
213480e12d sunxi: video: Add lvds support
Add support for lvds lcd panels

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
2015-01-14 14:56:40 +01:00
Hans de Goede
7fad8a9802 sunxi: video: Add a hpd_delay parameter to configure hpd delay
In some extreme cases it may be necessary to wait 1.5 seconds or more for a hpd
signal to show up (and be able to read edid info), but we do not want to
penalize all headless boots with an extra second boot delay, so add a hpd_delay
parameter which can be set through the video-mode env. variable.

While at it raise the default from 300ms to 500ms as 300 may very well be too
low in many cases.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14 14:56:39 +01:00
Hans de Goede
d9786d2380 sunxi: video: Add VGA output support
Add support for VGA directly from the sunxi SoC / display engine.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14 14:56:39 +01:00
Hans de Goede
49d2703dd8 sunxi: video: Fallback from HDMI to VGA on boards with VGA
If a board has no LCD, but does have VGA fallback to VGA when no HDMI cable
is connected (unless hpd=0).

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14 14:56:39 +01:00
Hans de Goede
3ffbe477da sunxi: video: Add support for using PORTD hsync/vsync pins with tcon1
Add support for using PORTD hsync/vsync pins with tcon1, this is a preparation
patch for adding native VGA support.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14 14:56:39 +01:00
Hans de Goede
6741cc78bb sunxi: video: Use sunxi_lcdc_get_clk_delay to calculate tcon1 delay
Use sunxi_lcdc_get_clk_delay to calculate tcon1 delay instead of hardcoding
it to 30. We will still end up using 30 for most modes, but for e.g. 800x600
this makes a (small) difference.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14 14:56:39 +01:00
Hans de Goede
b98d048030 sunxi: video: Remove sunxi_display.enabled variable
Having both a sunxi_display.enabled variable and
sunxi_display.monitor == sunxi_monitor_none duplicates state, use
sunxi_display.monitor = sunxi_monitor_none when ever we do not have a display.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14 14:56:39 +01:00
Hans de Goede
e2bbdfb1e3 sunxi: video: Add support for VGA via external DACs connected to the LCD pins
Add support for external DACs connected to the parallel LCD interface driving
a VGA connector, such as found on the Olimex A13 boards.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14 14:56:39 +01:00
Hans de Goede
2fbf091a54 sunxi: video: Enable video on sun8i, which supports LCD but not HDMI
The A23 (sun8i) only has lcd output support, so allow building the video code
without HDMI support for use with the A23.

Also the A23 has the same reset bits (and necessity to enable the DRC block)
as the sun6i, so enable those bits for sun8i too.

Note building without HDMI support is useful for the A13 (sun5i variant) too,
as that one does not have HDMI either.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14 14:56:39 +01:00
Hans de Goede
2dae800f1e sunxi: video: Add lcd output support
Add lcd output support, see the new Kconfig entries and doc/README.video for
how to enable / configure this.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14 14:56:39 +01:00
Hans de Goede
e84007933a sunxi: video: Move sunxi_drc_init
Move sunxi_drc_init to directly above sunxi_engines_init, to avoid
unnecessary #ifdef-ery in later patches.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14 14:56:39 +01:00
Hans de Goede
5489ebc7af sunxi: video: Modify sunxi_lcdc_pll_set to work with both tcon0 and tcon1
Modify sunxi_lcdc_pll_set to work with both tcon0 and tcon1, this is a
preparation patch for adding lcd support.

While at it also swap the divider search order, searching from low to
high, as the comment above the code says we should do. In cases where there
are multiple solutions this will result in picking a lower pll clock and
divider, which is more stable and saves power.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14 14:56:39 +01:00
Hans de Goede
0e04521557 sunxi: video: Prepare for lcd support
Refactor sunxi_mode_set into a bunch of helpers, and make it do a switch
case on sunxi_display.monitor to decide what to do.

Also rename sunxi_lcdc_mode_set to sunxi_lcdc_tcon1_mode_set, as it sets the
timings for tcon1, and for lcd support we need a similar function operating
on tcon0.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14 14:56:39 +01:00
Hans de Goede
1c092205a2 sunxi: video: Improve monitor video-mode option handling
Add a sunxi_monitor enum and parse the monitor option string into this enum
once, rather then doing strcmp-s on it in various places. This also adds
checking for it being a valid value.

This also adds new "none" and "lcd" values in preparation for lcd support.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14 14:56:39 +01:00
Hans de Goede
876aaafdbd sunxi: video: Set input sync enable
Add a write to the "unknown" (*) register to enable auto input sync, when
initially adding sunxi hdmi output support this magic write from the android
kernel code was missed, causing lcdc -> hdmi encoder sync problems.

With this write added, we can drop the modesetting retries and the extra
delays added to work around these sync problems.

With the retries dropped there also is no need to 0 all the enable flags at
the beginning of the modeset, as they are initialized to 0 already by
engines_init.

*) "unknown" is the actual name of this register in the android kernel sources

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Anatolij Gustschin <agust@denx.de>
2015-01-14 14:56:38 +01:00
Hans de Goede
40f1b87ce7 sunxi: video: Give hotplug-detect (hpd) signal some time to show up
When using a hdmi powered hdmi to vga dongle, and cold booting a sunxi
device, the hpd detect code would not see the dongle (until a warm reboot),
because the dongle needs some time to boot.

Testing has shown that this dongle needs 213ms to respond on a cold boot,
so wait up to 300ms for a hpd signal to show up before giving up.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Anatolij Gustschin <agust@denx.de>
2015-01-14 14:56:38 +01:00
Hans de Goede
f300068ddd sunxi: video: When using edid use CEA681 extension blocks to select hdmi output
When using edid use CEA681 edid extension blocks to select between dvi and
hdmi output formats, so that u-boot will automatically do the right thing.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Anatolij Gustschin <agust@denx.de>
2015-01-14 14:56:38 +01:00
Hans de Goede
63c5fbdfb9 sunxi: video: Add sunxi_hdmi_edid_get_block helper function
Add a sunxi_hdmi_edid_get_block helper function, this is a preparation patch
for adding support for parsing EDID extension blocks.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Anatolij Gustschin <agust@denx.de>
2015-01-14 14:56:38 +01:00
Hans de Goede
5ee0bea49a sunxi: video: Add hdmi support
So far we've been programming the hdmi-encoder to send out dvi data over the
hdmi connector. This works well for most devices, including hdmi devices, but
not all devices accept dvi data on a hdmi input.

Add support for sending proper hdmi data over the hdmi output found on most
sunxi boards. This can be turned on by adding monitor=hdmi as option to the
video-mode env. variable.

A follow up patch will determine whether to send dvi or hdmi automatically when
EDID is used.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Anatolij Gustschin <agust@denx.de>
2015-01-14 14:56:38 +01:00
Hans de Goede
75481607c7 sunxi: video: Add DDC & EDID support
Add DDC & EDID support and use it to automatically select the native mode of
the attached monitor. This can be disabled by adding edid=0 as option
to the video-mode env. variable.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Anatolij Gustschin <agust@denx.de>
2015-01-14 14:56:38 +01:00
Hans de Goede
518cef20f8 sunxi: video: Add hpd option
Allow the user to specify hpd=0 as option in the video-mode env. variable,
if hpd is set to 0 then the hdmi output will be brought up even if no cable
is connected.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Anatolij Gustschin <agust@denx.de>
2015-01-14 14:56:38 +01:00
Hans de Goede
5f33993b7e sunxi: video: Add support for video-mode environment variable
Add support for the standard video-mode environment variable using the
videomodes.c video_get_ctfb_res_modes() helper function.

This will allow users to specify the resolution e.g. :

setenv video-mode sunxi:video-mode=1280x1024-24@60
saveenv

Also make the reserved fb mem slightly larger to allow 1920x1200 to work.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Anatolij Gustschin <agust@denx.de>
2015-01-14 14:56:38 +01:00
Hans de Goede
be8ec63306 sunxi: video: Use video-mode/-timing from videomodes
Switch from fb_videomode to ctfb_res_modes and use the predefined videotimings
from videomodes.c, rather then defining our own.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Anatolij Gustschin <agust@denx.de>
2015-01-14 14:56:38 +01:00
Luc Verhaegen
2d7a084ba0 sunxi: video: Add simplefb support
Add simplefb support, note this depends on the kernel having support for
the clocks property which has recently been added to the simplefb devicetree
binding.

Signed-off-by: Luc Verhaegen <libv@skynet.be>
[hdegoede@redhat.com: Use pre-populated simplefb node under /chosen as
 disussed on the devicetree list]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>.
2014-11-25 13:38:46 +01:00
Hans de Goede
211717a463 sunxi: video: Add sun6i support
Besided needing the usual sun6i specific ahb1_reset bits poking, it turns out
that sun6i also needs the drc to be taken out of reset and clocked even though
it is in pass-through mode.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
2014-11-25 13:38:46 +01:00
Luc Verhaegen
7f2c521f90 sunxi: video: Add cfb console driver for sunxi
This adds a fixed mode hdmi driver for the sunxi platform. The fixed
mode is a relatively safe 1024x768, more complete EDID handling is
currently not provided. Only HDMI is supported today.

This code is enabled when HPD detects an attached monitor.

Current config is such that 8MB is shaved off at the top of the RAM.
This avoids several memory handling issues, most significant is the fact
that on linux on ARM you are not allowed to remap known RAM as IO. A
clued in display driver will be able to recycle this reserved RAM in
future though.

cfbconsole was chosen as it provides the most important functionality: a
working u-boot console, allowing for the debugging of certain issues
without the need for a UART.

Signed-off-by: Luc Verhaegen <libv@skynet.be>
[hdegoede@redhat.com: Major cleanups and some small bugfixes]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-11-25 13:38:46 +01:00