Often on boards exists a circuit which switches power on/off to LCD display.
Due to the need of limiting the in-rush current the output voltage from this
circuit rises "slowly", so it is necessary to wait a bit (VCC ramp up time)
before starting output on LCD-pins.
This time is specified in <n> ms within the panel-settings, called "pup_delay"
Further some LCDs need a couple of frames to stabilize the image on it.
We have now the possibility to wait some time after starting output on LCD.
This time is also specified in <n> ms within panel-settings, called "pon_delay"
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
Without this change the board support for these SPEAr boards would
be dropped soon. Generic board support seems to work just fine.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Vipin Kumar <vk.vipin@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Board can define its own AXI burst length to improve DWMAC DMA performance.
v2-changes:
- Avoid write burst len register when the Macro is not defined.
v3-changes:
- Add axi_bus register member to struct eth_dma_regs.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Bring checkstack.pl up to date from its upstream Linux development.
Effectively, the following linux commits:
208ad00 checkstack.pl: port to AArch64
fda9f99 scripts/checkstack.pl: automatically handle 32-bit and 64-bit mode for ARCH=x86
7eb6e34 kbuild: trivial - remove trailing empty lines
690998b scripts/checkstack.pl: Add metag support
Reported-by: York Sun <yorksun@freescale.com>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Currently, an environment variable must be used to store the randomly
generated UUID for each partition. This is not necessary, so make storing
the UUID optional. Now passing uuid_disk and uuid are optional when random
UUIDs are enabled.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
The gpt command always reports success even if writing the partition table
failed. Propagate the return value of gpt_restore so we get proper status
reported.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Przemyslaw Marczak <p.marczak@samsung.com>
According to table 2-3 on page 87 of Marvell's latest PXA270
Specification Update Rev. I from 2010.04.19 [1] there exists a breed of
chips with a new CPU ID for PXA270M A1 stepping which our latest
Colibri PXA270 V2.4A modules actually have assembled. This patch helps
in correctly identifying those chips upon boot as well which then looks
as follows:
CPU: Marvell PXA27xM rev. A1
[1] http://www.marvell.com/application-processors/pxa-family/assets/pxa_27x_spec_update.pdf
Acked-by: Marek Vasut <marex@denx.de>
Fix the name appearing in menuconfig for memtest command
Signed-off-by: Nikolaos Pasaloukos <Nikolaos.Pasaloukos@imgtec.com>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com
In 0200020 we added a number of tests for 'if
defined(CONFIG_SYS_FSL_SEC_LE) && !defined(CONFIG_MX6)' and
accidentally did one as 'ifdef defined...'
Signed-off-by: Tom Rini <trini@konsulko.com>
commit d9f43c8f5c sets
get_reset_cause() as static, but this conflicts with mx5
where its prototype is in sys_proto.h.
Drop it from sys_proto.h and drop print_cpuinfo from mx53_loco,
factorizing the call for this board.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Jason Liu <jason.hui@linaro.org>
Currently in some cases SDRAM init requires global_data to be available
and soon this will not be available prior to board_init_f(). Adjust the
code paths in these cases to be correct. In some cases we had the SPL
stack be in DDR as we might have large stacks (due to Falcon Mode +
Environment). In these cases switch to CONFIG_SPL_STACK_R. In other
cases we had simply been setting CONFIG_SPL_STACK into SRAM. In these
cases we no longer need to (CONFIG_SYS_INIT_SP_ADDR is used and is also
in SRAM) so drop those lines.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested on Beagleboard, Beagleboard xM
Tested-by: Matt Porter <mporter@konsulko.com>
Tested on Beaglebone Black, AM43xx GP EVM, OMAP5 uEVM, OMAP4 Pandaboard
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When CONFIG_SYS_MALLOC_SIMPLE is defined, free() is a static inline. Make
sure that the export interface still builds in this case.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present SPL uses a single stack, either CONFIG_SPL_STACK or
CONFIG_SYS_INIT_SP_ADDR. Since some SPL features (such as MMC and
environment) require a lot of stack, some boards set CONFIG_SPL_STACK to
point into SDRAM. They then set up SDRAM very early, before board_init_f(),
so that the larger stack can be used.
This is an abuse of lowlevel_init(). That function should only be used for
essential start-up code which cannot be delayed. An example of a valid use is
when only part of the SPL code is visible/executable, and the SoC must be set
up so that board_init_f() can be reached. It should not be used for SDRAM
init, console init, etc.
Add a CONFIG_SPL_STACK_R option, which allows the stack to be moved to a new
address before board_init_r() is called in SPL.
The expected SPL flow (for CONFIG_SPL_FRAMEWORK) is documented in the README.
Signed-off-by: Simon Glass <sjg@chromium.org>
For version 1:
Acked-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Heiko Schocher <hs@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Use the full driver model GPIO and serial drivers in SPL now that these are
supported. Since device tree is not available they will use platform data.
Remove the special SPL GPIO function as it is no longer needed.
This is all in one commit to maintain bisectability.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is already set up in crt0.S. We don't need a new structure and don't
really want one in the 'data' section of the image, since it will be empty
and crt0.S's changes will be ignored.
As an interim measure, remove it only if CONFIG_DM is not defined. This
allows us to press ahead with driver model in SPL and allow the stragglers
to catch up.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function has grown into something of a monster. Some boards are setting
up a console and DRAM here in SPL. This requires global_data which should be
set up in one place (crt0.S).
There is no need for SPL to use s_init() for anything since board_init_f()
is called immediately afterwards.
Signed-off-by: Simon Glass <sjg@chromium.org>
This commit removes the dram reservation from board file,
because it is done in a common code.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This commit enables the last DRAM bank and reserves
the last 22 MiB of it, for the secure firmware.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Akshay Saraswat <akshay.s@samsung.com>
Cc: Hyungwon Hwang <human.hwang@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Since more than one board requires memory reservation
for the secure firmware, the reservation code can be
made in a common code.
Now, to reserve some part of the the last bank,
board config should define:
- CONFIG_TZSW_RESERVED_DRAM - len in bytes
- CONFIG_NR_DRAM_BANKS - number of memory banks
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Akshay Saraswat <akshay.s@samsung.com>
Cc: Hyungwon Hwang <human.hwang@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add basic Xilinx ZynqMP arm64 support.
Serial and SD is supported.
It supports emulation platfrom ep108 and QEMU.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This code was introduced to support the multiple .config
configuration in U-Boot. We do not need it any more.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
With a389531 we now call readl() from this file so add <asm/io.h> so
that we have a prototype for the function.
Signed-off-by: Tom Rini <trini@konsulko.com>
With UMS support we are able to flash the eMMC from U-boot, which is very
convenient.
Add UMS support to make the eMMC flashing process easier.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Pass the same pad configuration as done in the kernel so that OTG1_ID pin can
properly work in device mode.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
After discussion during the last u-boot mini summit with USB maintainer -
Marek Vasut - it has been decided, that gadget development should be
coordinated by DFU custodian.
Such patch formalizes current development status.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Integrate latest validated register settings from Toradex WinCE BSP
4.2 working accross all module versions from early V1.x, V1.2D, V2.2B
to V2.4A.
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Specify a CONFIG_BOARD_SIZE_LIMIT of 256 KB in order to avoid
overwriting the factory configuration block located at offset 0x40000
in NOR flash.
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
To save more than 20 KB of precious space in NOR flash get rid of the
following configuration options:
CONFIG_CMD_LOADB
CONFIG_CMD_LOADS
CONFIG_SYS_LONGHELP
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Migrate Toradex Colibri PXA270 to use CONFIG_SYS_GENERIC_BOARD.
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
