Not really qcom specific, but for now qcom/lk is the one firmware that
is (afaiu) setting up the appropriate dt node for pre-configured
display. Uses the generic simple-framebuffer DT bindings so this should
be useful on other platforms.
Signed-off-by: Rob Clark <robdclark@gmail.com>
The STM32 LTDC display controller provides a parallel digital RGB and
signals for horizontal, vertical synchronization, Pixel Clock and Data
Enable as output to interface directly to a variety of LCD and TFT panels.
The LTDC main features are:
- 24-bit RGB Parallel Pixel Output, Programmable timings & polarity for
HSync, VSync and Data Enable.
- 2 layers with Blending, Color Keying, Window position & size,
Dithering, Background color, Color Look-Up Table (CLUT).
- Supported layer color formats: ARGB8888, RGB888, RGB565, ARGB1555,
ARGB4444, L8 CLUT, AL44 & AL88
This LTDC driver:
- supports: RGB parallel output with timings & polarity, 1 layer
in RGB565.
- supports but with hard-coded configurations: blending, window
position & size (crop), background color.
- does not support yet: rgb888, argb8888, 8-bit clut, dithering.
This LTDC driver is compatible with all stm32 platforms with the
LTDC IP and has been tested on stm32 f746-disco board.
Signed-off-by: Philippe CORNU <philippe.cornu@st.com>
Add a driver for GPIO backlights.
It understands the standard device tree binding.
It can be used with simple-panel when PWM is not necessary.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add a config to select individually the driver for PWM backlights.
Manage "depends on" to be backyard compatible.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
After a successful read of a UBI volume, the variable filesize is set
to the number of read bytes. To boot linux with a raw initramfs/initrd,
you must specify the exact size of the initramfs/initrd image in boot
command. If the initramfs/inird is read from UBI volume, $filesize is
required to access the number of read bytes.
Example:
ubi read ${loadaddr} kernelvol
ubi read ${fdtaddr} dtbvol
ubi read ${initrd_addr} initrdvol
bootz ${loadaddr} ${initrd_addr}:${filesize} ${fdt_addr}
Signed-off-by: Holger Dengler <dengler@linutronix.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
This allows to scan the DT including all "clocks" node's sub-nodes
in which fixed-clock are defined.
All fixed-clock should be defined inside a clocks node which collect all
external oscillators. Until now, all clocks sub-nodes can't be binded except
if the "simple-bus" compatible string is added which is a hack.
Update test.dts by moving clk_fixed node inside clocks.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently, all fixed-clock declared in "clocks" node in device tree
can be binded by clk_fixed_rate.c driver only if each of them have
the "simple-bus" compatible string.
This constraint has been invoked here [1].
This patch offers a solution to avoid adding "simple-bus" compatible
string to nodes that are not busses.
[1] https://patchwork.ozlabs.org/patch/558837/
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support for reading a list of bouncing addresses from a in-tree file
(doc/bounces) and from the ~/.patman config file. These addresses are
stripped from the Cc list.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com <mailto:philipp.tomsich@theobroma-systems.com>>
Adjust this code so that it can work with Python 2 and 3.
Fixes: d73fcb1 (moveconfig: Support building a simple config database)
Reported-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a convenience macro to iterate over subnodes of a node. Make use of
this where appropriate in the code.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we sometimes see warnings of the form:
/tmp/tmpMA89kB:36: warning: overriding the value of CMD_SPL.
Old value: "y", new value: "y".
This is not very useful as it does not show whch defconfig file it relates
to. Update the tool to show this.
Signed-off-by: Simon Glass <sjg@chromium.org>
We can use printf() to limit the string width. Adjust the code to do this
instead of using strlcpy() which is a bit clumbsy.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Convert SANDBOX_BITS_PER_LONG to Kconfig and assign it a correct
number depending on which host we are going to build and run.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
It seems most of the time we are building and running sandbox on 64-bit host.
But we do support 32-bit host as well. Introduce Kconfig option for this.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
There is an overflow problem when taking the size instead of the number
of blocks in blk_create_device(). This results in a wrong device size: the
device apparent size is its real size modulo 4GB.
Using the number of blocks instead of the device size fixes the problem and
is more coherent with the internals of the block layer.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This option is an SPL-variant of the I2C_EEPROM option to enable
the driver for generic I2C-attached EEPROMs for SPL.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add the code to set the ethernet mac address from eeprom by using
the common code from the common folder.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Replace the code to set the ethernet mac address with the code from
the common folder.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Create board/$(VENDOR)/common folder to accommodate the common code
shared by other atmel boards, now put the code to set ethernet mac
address from eeprom, which uses the i2c eeprom driver.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support for selecting proper dtb for
am57xx BeagleBoard X15 revC u-boot from FIT
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
AM571x supports DDR running at 666MHz. Right now it is
clocked at 532MHz which is lower than what is supported.
In order to have maximum performance on AM571-IDK,
switch DDR to 666MHz.
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add support for selecting proper dtb for
dra76x u-boot from FIT.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Separate out u-boot specific compatibles from dts files.
This will help in syncing dts files in future.
Also these will get deleted eventually once respective drivers
are capable of handling Linux dts files.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Adding pinmux and IODELAY data for dra76-evm.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
dra76-evm has the ddr parts connectedi running at 666MHz:
EMIF1: MT41K512M16HA-125 AIT:A x 2
EMIF2: MT41K512M8RH-125-AAT:E x 4
Add support for configuring the above DDR parts.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
dra76-evm uses lp8736 and tps65917 pmic for powering on
various peripherals. Add data for these pmics and register
for dra76-evm.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The dra76-evm is a board based on TI's DRA76 processor
Add eeprom support
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
dra76 family is a high-performance, infotainment application
device, based on OMAP architecture on a 28-nm technology.
This contains most of the subsystems, peripherals that are
available on dra74, dra72 family. This SoC mainly features
Subsystems:
- 2 x Cortex-A15 with max speed of 1.8GHz
- 2 X DSP
- 2 X Cortex-M4 IPU
- ISS
- CAL
- DSS
- VPE
- VIP
Connectivity peripherals:
- 1 USB3.0 and 3 USB2.0 subsystems
- 1 x SATA
- 2 x PCI Express Gen2
- 3-port Gigabit ethernet switch
- 2 x CAN
- MCAN
Adding CPU detection support for the dra76 ES1.0 soc
and update prcm, control module, dplls data.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Praneeth Bajjuri <praneeth@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
LP87565 is present on dra76-evm. Select it for
TARGET_DRA7XX_EVM.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
It is not necessary that ldo1 is used to power on mmc.
So, add support for passing ldo registers for powering on mmc.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
It is not necessary all omap5+ based uses the same PMIC
to poweron mmc. So add support for enabling mmc based on board.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
CCN-504 HPF registers were believed to be accessible only from EL3.
However, recent tests proved otherwise. Remove checking for exception
level to re-enable L3 cache flushing for all levels.
Signed-off-by: York Sun <york.sun@nxp.com>
Tested-by: Zhao Qiang <qiang.zhao@nxp.com>
The pcie config space of ls1088a is different from ls2080a.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
In case high region memory doesn't have enough space for Management
Complex (MC), the return value should indicate a failure so the
caller can handle it accordingly.
Signed-off-by: York Sun <york.sun@nxp.com>
Reported-by: Ebony Zhu <ebony.zhu@nxp.com>
Rx Compliance tests may fail intermittently at high
jitter frequencies using default register values
Program register USB_PHY_RX_OVRD_IN_HI in certain sequence
to make the Rx compliance test pass.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Suresh Gupta <suresh.bhagat@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
Low Frequency Periodic Singaling (LFPS) Peak-to-Peak Differential
Output Voltage Test Compliance fails using default transmitter settings
Change config of transmitter signal swings by setting register
PCSTXSWINGFULL to 0x47 to pass compliance tests.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
The default setting for USB High Speed Squelch Threshold results
in a threshold close to or lower than 100mV. This leads to Receive
Compliance test failure for a 100mV threshold.
Shift the threshold from ~100mV towards ~130mV by setting SQRXTUNE
to 0x0 to pass USB High Speed Receiver Sensitivity Compliance test.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
USB High Speed (HS) EYE Height Adjustment
USB HS speed eye diagram fails with the default value at
many corners, particularly at a high temperature
Optimal eye at TXREFTUNE value to 0x9 is observed, change
set the same value.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
Rx Compliance tests may fail intermittently at high
jitter frequencies using default register values.
Program register USB_PHY_RX_OVRD_IN_HI in certain sequence
to make the Rx compliance test pass.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Suresh Gupta <suresh.bhagat@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
Low Frequency Periodic Signaling(LFPS) Peak-to-Peak Differential
Output Voltage Test Compliance fails using default transmitter
settings
Change config of transmitter signal swings by setting register
PCSTXSWINGFULL to 0x47 to pass compliance tests.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
