This patch adds USB configs to support the USB OTG port(consist
of DWC2 controller) and the USB Host port(consist of EHCI and OHCI
controllers) on evb-rv1108 board, and also support fastboot over
USB and USB mass storage.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The NXP 4.1 kernel needs to boot with secure boot.
Add information on how to enable secure boot mode.
Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Update these macros to use all upper-case to avoid checkpatch
warnings:
ENET_25MHz,
ENET_50MHz,
ENET_125MHz,
Signed-off-by: Eric Nelson <eric@nelint.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
The current mechanism using SCR/GPR registers work well when
the serial downloader boot mode has been selected explicitly
(either via boot mode pins or using bmode command). However,
in case the system entered boot ROM due to unbootable primary
boot devices (e.g. empty eMMC), the SPL fails to detect that
it has been downloaded through serial loader and tries to
continue booting from eMMC:
Trying to boot from MMC1
mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###
The only known way to reliably detect USB serial downloader
is by checking the USB PHY receiver block power state...
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Eric Nelson <eric@nelint.com>
This macro allows to detect whether the USB PHY is active. This
is helpful to detect if the boot ROM has previously started the
USB serial downloader.
The idea is taken from the mfgtool support in the NXP U-Boot:
http://git.freescale.com/git/cgit.cgi/imx/uboot-imx.git/commit/?h=imx_v2016.03_4.1.15_2.0.0_ga&id=a352ed3c5184b95c4c9f7468f5fbb5f43de5e412
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Eric Nelson <eric@nelint.com>
Starting from PXs3, the bit fields of RSTCTRL, CLKCTRL registers
will change every SoC. There is no more point to define bitfields
in the common header file.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The main difference between Pro4 and PXs2/LD6b is the Denali NAND
IP version. This is now distinguished by DT. Merge the two defconfig
files into uniphier_v7_defconfig.
Update the README.uniphier too.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The Denali IP does not update the revision register properly.
Allow to override it with SoC data associated with compatible.
Linux had already finished big surgery of this driver, but I need
to prepare the NAND core before the full sync of the driver.
For now, I am fixing the most fatal problem on UniPhier platform.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
legacy_hole_base_k and legacy_hole_size_k are defined but
not used.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Enable this option for link so that the timer is available earlier.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
With SPL we often have limited memory and do not need very many bootstage
records. Add a separate Kconfig option for SPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The CONFIG_BOOTSTAGE_USER_COUNT option is no-longer needed since we can now
support any number of user IDs. Also BOOTSTAGE_ID_COUNT is not needed now.
Drop these unused options.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
With bootstage we need access to the timer before driver model is set up.
To handle this, put the required state in global_data and provide a new
function to set up the device, separate from the driver's probe() method.
This will be used by the 'early' timer also.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Once U-Boot relocates itself the existing driver-model timer (if any) is
no-longer valid until the device is reinitialised. Any use of the device
may cause a crash. To handle this, set the timer to NULL after relocation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This adds support to Intel Cherry Hill board, a board based on
Intel Braswell SoC. The following devices are validated:
- serial port as the serial console
- on-board Realtek 8169 ethernet controller
- SATA AHCI controller
- EMMC/SDHC controller
- USB 3.0 xHCI controller
- PCIe x1 slot with a graphics card
- ICH SPI controller with an 8MB Macronix SPI flash
- Integrated graphics device as the video console
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
FSP's built-in UPD configuration enables PUNIT power configuration,
but on B0 stepping, this causes CPU hangs in fsp_init(). Disable it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds microcode device tree fragment for Braswell B0 (406C2),
C0 (406C3) and D0 (406C4) stepping SoC.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds initial Intel Braswell SoC support. It uses Intel FSP
to initialize the chipset.
Similar to its predecessor BayTrail, there are some work to do to
enable the legacy UART integrated in the Braswell SoC.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
FSP spec 1.1 adds 3 new APIs and their offsets are in the header.
Update the 'fsp hdr' command to show these new entries.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When a VBT is given to an FSP that supports graphics initialization,
the FSP will produce a graphics info HOB that contains all necessary
information for the linear frame buffer of the integrated graphics
device. This adds a DM video driver for it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Now that binman is able to recognize the Video BIOS Table entry,
add such one in the u-boot.dtsi.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds Kconfig options for Video BIOS Table which is normally
required if you are using an Intel FSP firmware that is complaint
with spec 1.1 or later to initialize the integrated graphics device.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds a new HOB type for graphics information introduced in FSP
spec 1.1. When graphics capability is included in FSP and enabled,
FSP produces an FSP_GRAPHICS_INFO_HOB as described in the EFI PI
specification which provides information about the graphics mode and
framebuffer.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
FSP spec 1.1 adds one more member to the struct common_buf to
determine the memory size that can be reserved by FSP below "top
of low usable memory" for bootloader usage. This new member uses
the reserved space so that it is still compatible with previous
FSP spec 1.0.
A new HOB (FSP_HOB_RESOURCE_OWNER_BOOTLOADER_TOLUM_GUID) is also
published when common_buf.tolum_size is valid and non zero.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Per the Intel 64 and IA-32 Architecture Software Developer's Manual,
add the reference clock for Intel Atom Processors based on the Airmont
Microarchitecture (Braswell).
This keeps in sync with Linux kernel commit:
6fcb41c: x86/tsc_msr: Add Airmont reference clock values
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Make various changes to the GPT test:
1) Reference the disk image using an absolute path in all cases. This
allows test/py to operate correctly if it's run from a directory other
than the root of the U-Boot source tree.
2) Store the disk image in the teswt/py persistent data directory. This
removes the need to re-generate it every time the tests are run.
3) Execute sgdisk using u_boot_utils.run_and_log() so that its output is
captured in the test log. This allows debugging any problems running it.
4) Make the disk image a test fixture. This removes the requirement to
always run all GPT tests, and run them in order. The current code doesn't
create the disk image if e.g. just test_gpt_uuid() is executed via the
test.py -k command-line option.
5) Use @pytest.mark.buildconfigspec for all feature dependencies, rather
than manually implementing some of them.
6) Make all tests depend on sandbox, since they use the sandbox-specific
host command.
Fixes: a2f422555f ("add pytests for 'gpt guid' command in sandbox")
Fixes: c5772188ed ("add pytests for 'gpt rename' and 'gpt swap'")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Tom Rini <trini@konsulko.com>
Nothing CONFIG_SOC_DA830 anymore, so let's remove it and
the one remaining source file for it. It appears to have been
abandoned a while ago.
Signed-off-by: Adam Ford <aford173@gmail.com>
commit b63b995 (arm: dts: Add u-boot specific compatibles) separated out
u-boot specific compatibles from dts files.
The u-boot specifics were moved in *-u-boot.dtsi files for all dra7
platforms except dra7-evm.
Without it the SD card is broken on DRA7-evm because the regulator cannot
be enabled.
Fix it by adding the missing dra7-evm-u-boot.dtsi with the needed
properties.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
When the OP-TEE image is built for secure paging the load address may be
in SRAM, remove checks that prevent this.
Signed-off-by: Harinarayan Bhatta <harinarayan@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
A new fatbuf was allocated by get_fs_info() (called by fat_itr_root()),
but not freed, resulting in eventually running out of memory. Spotted
by running 'ls -r' in a large FAT filesystem from Shell.efi.
fatbuf is mainly used to cache FAT entry lookups (get_fatent())..
possibly once fat_write.c it can move into the iterator to simplify
this.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Łukasz Majewski <lukma@denx.de>
Use the clust_to_sect() helper that was introduced earlier, and add an
inverse sect_to_clust(), plus update the various spots that open-coded
this conversion previously.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Noticed when comparing our output to linux. There are some lcase bits
which control whether filename and/or extension should be downcase'd.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Łukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a generic implementation of 'ls' using opendir/readdir/closedir, and
replace fat's custom implementation. Other filesystems should move to
the generic implementation after they add opendir/readdir/closedir
support.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Łukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Spotted by chance, when trying to remove file_fat_ls(), I noticed there
were some dead users of the API.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Acked-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Implement the readdir interface using the directory iterators.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Łukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Needed to support efi file protocol. The fallback.efi loader wants
to be able to read the contents of the /EFI directory to find an OS
to boot.
Modelled after POSIX opendir()/readdir()/closedir(). Unlike the other
fs APIs, this is stateful (ie. state is held in the FS_DIR "directory
stream"), to avoid re-traversing of the directory structure at each
step. The directory stream must be released with closedir() when it
is no longer needed.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Łukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
And drop a whole lot of ugly code!
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Łukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Untangle directory traversal into a simple iterator, to replace the
existing multi-purpose do_fat_read_at() + get_dentfromdir().
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Łukasz Majewski <lukma@denx.de>
Want to re-use this in fat dirent iterator in next patch.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Łukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
While there are valid reasons to use __packed, often the answer is that
you should be doing something else here instead.
This reintroduces the changes of
f503cc49a5 (Add warning for new __packed additions)
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
