Init the CPU and its buses to speed up the boot time.
Move rkclk_init() to a place after rk3399_configure_cpu has defined
at the same time, or else there will be a warning.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
BOOT_TARGET_DEVICES should only be added if the corresponding u-boot
command is enabled.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
rockchip-common.h already defines values that are missing from
rk3368_common.h
For example BOOT_TARGET_DEVICES was defined empty and therefore
distroboot had no boot targets.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Inside setup_sata() there is a cpu type check, so there is no need to
do this check in the board file.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Inside setup_sata() there is a cpu type check, so there is no need to
do this check in the board file.
This also brings the benefit to allowing setup_sata() to be called for the
mx6qp wandboard variant.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Enable UMS and DFU, so that the eMMC can be accessed via the
USB gadget port on the board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Since DM_USB enabled, no need the usb code in board file.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Commit 001cdbbb32 ("imx: mx6slevk: enable more DM drivers") breaks
MMC support in U-Boot proper on the mx6slevk_spl_defconfig target:
U-Boot SPL 2017.09-00396-g6ca43a5 (Oct 01 2017 - 16:20:18)
Trying to boot from MMC1
U-Boot 2017.09-00396-g6ca43a5 (Oct 01 2017 - 16:20:18 -0300)
CPU: Freescale i.MX6SL rev1.0 792 MHz (running at 396 MHz)
CPU: Commercial temperature grade (0C to 95C) at 33C
Reset cause: POR
Board: MX6SLEVK
I2C: ready
DRAM: 1 GiB
MMC: FSL_SDHC: 0
MMC Device 1 not found
*** Warning - No MMC card found, using default environment
As mx6slevk_spl_defconfig does not use CONFIG_DM_MMC and its
board file does not register the mmc controller for U-Boot proper,
let's fix this by adding CONFIG_DM_MMC=y and device tree support.
While at it, add more DM drivers, so that it becomes closer to
mx6slevk_defconfig.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Add support for the latest MX6QP wandboard variant.
Based on Richard Hu's work from Technexion's U-Boot tree.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
On Vybrid SoCs U-Boot gets loaded into GFX SRAM which is 512KiB.
Currently 32KiB is reserved for the IMX header. However, this is
not reflected in the size limit. In v2017.11-rc2 the actual size
limit (512KiB-32KiB) has been reached for Colibri VF61, which
lead to a successful build of U-Boot but not a working binary.
The IMX header is much smaller than 32KiB, typically around 1KiB.
Decrease the reserved size to 4KiB and specify the correct U-Boot
size limit. Apply this new base address and limit for all Vybrid
based boards.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
As reported by Jonathan Gray:
"After the recent changes to add SimpleNetworkProtocol to efi_loader
when booting off mmc via an efi payload that doesn't use
SimpleNetworkProtocol U-Boot's fec_mxc driver will now display
various "error frame" messages.
....
MMC Device 1 not found
MMC Device 2 not found
MMC Device 3 not found
Scanning disks on sata...
Found 6 disks
reading efi/boot/bootarm.efi
67372 bytes read in 32 ms (2 MiB/s)
## Starting EFI application at 12000000 ...
>> OpenBSD/armv7 BOOTARM 1.0
error frame: 0x8f57ec40 0x00003d74
error frame: 0x8f57ec40 0x00007079
error frame: 0x8f57ec40 0x00006964
error frame: 0x8f57ec40 0x00006f6f
error frame: 0x8f57ec40 0x0000726f
error frame: 0x8f57ec40 0x00002074
error frame: 0x8f57ec40 0x00006f6f"
Heinrich Schuchardt explains:
"A receive FIFO overrun can be expected if network packages are not
processed.
With the network patches we check if a package is available quite often."
Move the "error frame" messages to debug level so that a clean output
log can be seen.
Reported-by: Jonathan Gray <jsg@jsg.id.au>
Suggested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
When CONFIG_DM_MMC=y, CONFIG_BLK should be selected, otherwise the
SD/eMMC card cannot be used.
Also, select CONFIG_DM_USB=y when CONFIG_USB=y to avoid build failure.
Tested on mx6slevk, mx7dsabresd and mx6ullevk.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Adam Ford <aford173@gmail.com>
Tested-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Tested-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Many MAINTAINERS files are in subdirectories.
We should enable searching these.
Reported-by: Walt Feasel <waltfeasel@gmail.com>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Allow prefixing typical strings with L for wide strings
Patch originally by Joe Perches
https://lkml.org/lkml/2017/10/17/1117
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Resort to malloc_cache_aligned() rather than malloc() which also removes
'CACHE: Misaligned operation at range' warnings.
Signed-off-by: Niko Mauno <niko.mauno@vaisala.com>
With the introduction of EFI variable support, we also wanted to persist
these EFI variables. However, the way it was implemented we ended up
persisting all U-Boot environment variables on every EFI boot.
That could potentially lead to unexpected side effects because variables
that were not supposed to be written to persisted env get written. It also
means we may end up writing the environment more often than we should.
For this release, let's just disable EFI variable persistence and instead
implement it properly for the next one.
Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Fixes: ad644e7c18 ("efi_loader: efi variable support")
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Enable support for loadables in SEC firmware FIT image. Currently
support is added for single loadable image.
Brief description of implementation:
Add two more address pointers (loadable_h, loadable_l) as arguments to
sec_firmware_init() api.
Create new api: sec_firmware_checks_copy_loadable() to check if loadables
node is present in SEC firmware FIT image. If present, verify loadable
image and copies it to secure DDR memory.
Populate address pointers with secure DDR memory addresses where loadable
is copied.
Example use-case could be trusted OS (tee.bin) as loadables node in SEC
firmware FIT image.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Change DDR allocated for secure memory from 2 MB to 66 MB. This
additional 64 MB secure memory is required for trusted OS running
in Trusted Execution Environment using ARMv8 TrustZone.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Signed-off-by: Amrita Kumari <amrita.kumari@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Amrita Kumari <amrita.kumari@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Because COMFIG_DM_USB has been enabled and will not use it anymore.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: York Sun <york.sun@nxp.com>
use Kconfig to select xhci accordingly.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Use Kconfig to select QE-HDLC and USB pin-mux.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Since TX delay is now enabled only in PHY_INTERFACE_MODE_RGMII_ID
PHY_INTERFACE_MODE_RGMII_TXID.
These change where introduced in phy driver in commit 05b29aa0cb
("net: phy: realtek: fix enabling of the TX-delay for RTL8211F").
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
On ls1012a soc, core clock source frequency is fixed at 100Mhz.
Generic timer frequency is core clock source divided by 4, which
is 25Mhz.
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Memory allocated via malloc is not guaranteed to be zeroized.
So explicitly use calloc instead of malloc.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This macro is defined, but not referenced by anyone.
I did not touch config_whitelist.txt - the CONFIG will be dropped
by the next re-sync.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This macro is defined, but not referenced by anyone.
I did not touch config_whitelist.txt - the CONFIG will be dropped
by the next re-sync.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
This macro is defined, but not referenced by anyone.
I did not touch config_whitelist.txt - the CONFIG will be dropped
by the next re-sync.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This macro is defined, but not referenced by anyone.
I did not touch config_whitelist.txt - the CONFIG will be dropped
by the next re-sync.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This macro is defined, but not referenced by anyone.
I did not touch config_whitelist.txt - the CONFIG will be dropped
by the next re-sync.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This macro is defined, but not referenced by anyone.
I did not touch config_whitelist.txt - the CONFIG will be dropped
by the next re-sync.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This macro is defined, but not referenced by anyone.
I did not touch config_whitelist.txt - the CONFIG will be dropped
by the next re-sync.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
This comment creates a wrong entry in config_whitelist.txt.
I did not touch config_whitelist.txt - the CONFIG will be dropped
by the next re-sync.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This macro is defined, but not referenced by anyone.
I did not touch config_whitelist.txt - the CONFIG will be dropped
by the next re-sync.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This macro is defined, but not referenced by anyone.
I did not touch config_whitelist.txt - the CONFIG will be dropped
by the next re-sync.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This macro only appears in commented-out lines. It is not referenced
by anyone.
I did not touch config_whitelist.txt - the CONFIG will be dropped
by the next re-sync.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This macro is defined, but not referenced by anyone.
I did not touch config_whitelist.txt - the CONFIG will be dropped
by the next re-sync.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This macro is defined, but not referenced by anyone.
I did not touch config_whitelist.txt - the CONFIG will be dropped
by the next re-sync.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This macro is defined, but not referenced by anyone.
I did not touch config_whitelist.txt - the CONFIG will be dropped
by the next re-sync.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Heiko Schocher<hs@denx.de>
CONFIG_SYS_I2C_FTI2C010 is not enabled by anyone.
Commit 2852709676 ("dm: i2c: Add a note to I2C drivers which need
conversion") prompted to convert this driver to DM before June 2017,
but not converted yet.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Heiko Schocher <hs@denx.de>
This driver was used by Blackfin boards, but Blackfin support is
gone. There is no user of this driver.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Heiko Schocher <hs@denx.de>
