This patch enhances the Octeon TX/TX2 watchdog driver to fully enable
the WDT. With this changes, the "wdt" command is now also supported
on these platforms.
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Suneel Garapati <sgarapati@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Remove a left-over debug test message from the Octeon TX / TX2
MMC driver.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Suneel Garapati <sgarapati@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Octeon TX2 sets the TB100_EN bit in the config register. We need to use
a fixed 100MHz clock for this as well to work properly.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Suneel Garapati <sgarapati@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
- fsl_esdhc_imx cleanup
- not send cm13 if send_status is 0.
- Add reinit API
- Add mmc HS400 for fsl_esdhc
- Several cleanup for fsl_esdhc
- Add ADMA2 for sdhci
- Octeon TX: Add NAND driver (Suneel)
- Octeon TX: Add NIC driver driver (Suneel)
- Octeon TX2: Add NIC driver driver (Suneel)
- Armada 8040: Add iEi Puzzle-M80 board support (Luka)
- Armada A37xx SPI: Add support for CS-GPIO (George)
- Espressobin: Use Linux model/compatible strings (Andre)
- Espressobin: Add armada-3720-espressobin-emmc.dts from Linux (Andre)
- Armada A37xx: Small cleanup of config header (Pali)
Set the defaults on probe for the packet buffer size registers
for the i210.
The TX/RX PBSIZE register of the i210 resets to its default value
only at power-on - see Intel Ethernet Controller I210 Datasheet rev 3.5
chapter 8.3 'Internal Packet Buffer Size Registers'.
If something (another driver, another OS, etc.) modifies this register
from its default value, the e1000 driver doesn't function correctly. It
detects a hang of the transmitter and continuously resets the adapter.
Here we set this value to its default when resetting the i210 to
resolve this issue.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
CONFIG_IS_ENABLED() takes the kconfig name without the CONFIG_ prefix,
e.g. CONFIG_IS_ENABLED(CLK) for CONFIG_CLK. Some of these were being
fixed every now and then, see:
commit 71ba2cb0d6 ("board: stm32mp1: correct CONFIG_IS_ENABLED usage for LED")
commit a5ada25e42 ("rockchip: clk: fix wrong CONFIG_IS_ENABLED handling")
commit 5daf6e56d3 ("common: console: Fix duplicated CONFIG in silent env callback")
commit 48bfc31b64 ("MIPS: bootm: Fix broken boot_env_legacy codepath")
Fix all files found by `git grep "CONFIG_IS_ENABLED(CONFIG"` by running
':%s/CONFIG_IS_ENABLED(CONFIG_\(\w+\))/CONFIG_IS_ENABLED(\1)/g' in vim.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Since it's so trivial I could just about tolerate this when there were only
two copies of it. But now there are about to be three.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
For testing purposes keep the output value when switching to input.
This allows us to manipulate the input value via the gpio command.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
Newer eSDHC controllers support ADMA2 descriptor tables which support
64bit DMA addresses. One notable user of addresses in the upper memory
segment is the EFI loader.
If support is enabled, but the controller doesn't support ADMA2, we
will fall back to SDMA (and thus 32 bit DMA addresses only).
Signed-off-by: Michael Walle <michael@walle.cc>
The device tree has a way to specify GPIO lines as chip selects. From
the binding docs:
So if for example the controller has 2 CS lines, and the cs-gpios
property looks like this:
cs-gpios = <&gpio1 0 0> <0> <&gpio1 1 0> <&gpio1 2 0>;
Then it should be configured so that num_chipselect = 4 with the
following mapping:
cs0 : &gpio1 0 0
cs1 : native
cs2 : &gpio1 1 0
cs3 : &gpio1 2 0
Add support for this, while retaining backward-compatibility with
existing device trees; the driver will preserve existing behavior if a
cs-gpios list is not given, or if a particular line is specified as <0>
(native).
This implementation is inspired by similar implementations in
neighboring drivers for other platforms: atmega, mxc, etc.
Signed-off-by: George Hilliard <ghilliar@amazon.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Adds support for Network Interface controllers found on
OcteonTX2 SoC platforms.
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Adds support for Network Interface controllers found on
OcteonTX SoC platforms.
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Adds support for NAND controllers found on OcteonTX or
OcteonTX2 SoC platforms. Also includes driver to support
Hardware ECC using BCH HW engine found on these platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
- Minor cleanup on K3 env variables
- Fix OSPI compatible for J721e
- Drop unused property in omap-usb2-phy
- Update Maintainer for am335x-guardian board.
Currently, readl/writel and esdhc_read32/esdhc_write32 are used. To align
the usage, change to only use esdhc_read32/esdhc_write32.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
There are other (non-SDHCI) controllers which supports ADMA2 descriptor
tables, namely the Freescale eSDHC. Instead of copying the code, move it
into an own module.
Signed-off-by: Michael Walle <michael@walle.cc>
First, we need the waterlevel setting for PIO mode only. Secondy, both DMA
setup code is identical for both directions, except for the data pointer.
Thus, unify them.
Signed-off-by: Michael Walle <michael@walle.cc>
Use the dma_{map,unmap}_single() calls. These will take care of the
flushing and invalidation of caches.
Signed-off-by: Michael Walle <michael@walle.cc>
SDMA can only do DMA with 32 bit addresses. This is true for all
architectures (just doesn't apply to 32 bit ones). Simplify the code and
remove unnecessary CONFIG_FSL_LAYERSCAPE.
Also make the error message more concise.
Signed-off-by: Michael Walle <michael@walle.cc>
This 1ms delay before sending command already exist from the beginning
of the fsl_esdhc driver added in year 2008. Now this driver has been
split for two files: fsl_esdhc.c and fsl_esdhc_imx.c. fsl_esdhc_imx.c
only for i.MX series. i.MX series esdhc/usdhc do not need this 1ms delay
before sending any command. So remove this 1ms, this will save a lot
time if handling a large mmc data.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
According to the code logic in __mmc_switch, if the parameter 'send_status'
is zero, no need to send cmd13, just wait the stated timeout time, then
can return directly.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
There was a fix-up for eMMC HS400 stability issue in Linux.
Patch link:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/
commit/?id=58d0bf843b49fa99588ac9f85178bd8dfd651b53
Description:
Currently only LX2160A eSDHC supports eMMC HS400. According to
a large number of tests, eMMC HS400 failed to work at 150MHz,
and for a few boards failed to work at 175MHz. But eMMC HS400
worked fine on 200MHz. We hadn't found the root cause but
setting eSDHC_DLLCFG0[DLL_FREQ_SEL] = 0 using slow delay chain
seemed to resovle this issue. Let's use this as fixup for now.
Introduce the fix-up in u-boot since the issue could be reproduced
in u-boot too.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Fix mmc->clock with actual clock which is divided by the
controller, and record it with priv->clock which was removed
accidentally.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
The process for eMMC HS400 mode for eSDHC is,
1. Perform the Tuning Process at the HS400 target operating frequency.
Latched the clock division value.
2. if read transaction, then set the SDTIMNGCTL[FLW_CTL_BG].
3. Switch to High Speed mode and then set the card clock frequency to
a value not greater than 52Mhz
4. Clear TBCTL[TB_EN],tuning block enable bit.
5. Change to 8 bit DDR Mode
6. Switch the card to HS400 mode.
7. Set TBCTL[TB_EN], tuning block enable bit.
8. Clear SYSCTL[SDCLKEN]
9. Wait for PRSSTAT[SDSTB] to be set
10. Change the clock division to latched value.Set TBCTL[HS 400 mode]
and Set SDCLKCTL[CMD_CLK_CTRL]
11. Set SYSCTL[SDCLKEN]
12. Wait for PRSSTAT[SDSTB] to be set
13. Set DLLCFG0[DLL_ENABLE] and DLLCFG0[DLL_FREQ_SEL].
14. Wait for delay chain to lock.
15. Set TBCTL[HS400_WNDW_ADJUST]
16. Again clear SYSCTL[SDCLKEN]
17. Wait for PRSSTAT[SDSTB] to be set
18. Set ESDHCCTL[FAF]
19. Wait for ESDHCCTL[FAF] to be cleared
20. Set SYSCTL[SDCLKEN]
21. Wait for PRSSTAT[SDSTB] to be set.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Add a mmc_hs400_prepare_ddr() interface for controllers
which needs preparation before switching to DDR mode for
HS400 mode.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Some controllers may have difference between HS200 tuning
and HS400 tuning, such as different registers setting,
different procedure, or different errata.
This patch is to add a hs400_tuning flag to identify the
tuning for HS400 mode.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
For DM_MMC, the controller re-initialization is needed to
clear old configuration for mmc rescan.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
"ti,dis-chg-det-quirk" property is not part of Linux kernel DT binding
documentation. Therefore drop this and instead use soc_device_match()
to distinguish b/w AM654 SR1.0 and SR2.0 devices similar to Linux kernel
driver.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reset the channel completely during channel release in order to clear
teardown bit before handing over to next user or jumping to Linux.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Enable FPGA full reconfiguration support with Intel FPGA SDM
Mailbox driver for Agilex.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Ensure watchdog reset is not triggered if the fpga
reconfiguration is taking too long.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Rename Stratix10 FPGA driver to Intel FPGA SDM Mailbox driver
because it is using generic SDM (Secure Device Manager) Mailbox
interface shared by other platform (e.g. Agilex) as well.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Rename the driver from S10 to SoC64 because Intel Agilex platform
also using the this SYSRESET SoCFPGA driver for S10.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Add additional membus writes to configure main and peripheral PLL
for Agilex's clock manager.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Since warm reset may optionally set the CLock Manager to'boot mode',
the clock driver should always force the Agilex's Clock Manager to
'boot mode' before the clock driver start configuring the Clock Manager
in SPL.
In SSBL, clock driver will skip the Clock Manager configuration
if it's already being setup by SPL (Clock Manager NOT in 'boot
mode') to prevent any inaccurate clocking issues happened on HPS
peripherals such as UART, MAC and etc.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Some drivers probing failed if clock enable function is not supported in
clock driver. So, add clock enable function to clock driver to solve it.
Return 0 (success) for *.enable function because all clocks are enabled
by default in clock driver probe.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
The timeout calculation is based on the clk being in KHz but
the clk api returns the clk value in Hz. Convert this to KHz
to calculate the correct timeout value.
Signed-off-by: Jack Mitchell <ml@embed.me.uk>
This more closely mirrors Linux's behaviour, and will make it easier to
transition to using function+color in the future.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
dm_gpio_ops.get_value can be called when the gpio is either input or
output. The current dw code always returns the input value, which is
invalid if the direction is set to out.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Previously, if there was no bank-name property, it was easy to have
confusing gpio names like "gpio1@08", instead of "gpio1@0_8". This patch
follows the example of the sifive gpio driver.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
