Pass the ethernet MAC address to the kernel upon boot. This passes both
the local-mac-address property (as passed to U-Boot from cboot) and the
currently set MAC address via the mac-address property. The latter will
only be set if it is different from the address that was already passed
via the local-mac-address property.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Note that U-Boot is always chainloaded from cboot starting with L4T
release 28. cboot always loads U-Boot to a fixed address, so making
the builds position independent isn't strictly necessary. However,
position independent builds can be convenient because if U-Boot is
ever loaded to an address different from its link address, it will
still be able to boot.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Read the boot arguments passed by cboot via the /chosen/bootargs
property and store it in the cbootargs environment variable.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This function will attempt to look up an Ethernet address in the DTB
that was passed in from cboot. It does so by first trying to locate the
default Ethernet device for the board (identified by the "ethernet"
alias) and if found, reads the "local-mac-address" property. If the
"ethernet" alias does not exist, or if it points to a device tree node
that doesn't exist, or if the device tree node that it points to does
not have a "local-mac-address" property or if the value is invalid, it
will fall back to the legacy mechanism of looking for the MAC address
stored in the "nvidia,ethernet-mac" or "nvidia,ether-mac" properties of
the "/chosen" node.
The MAC address is then written to the default Ethernet device for the
board (again identified by the "ethernet" alias) in U-Boot's control
DTB. This allows the device driver for that device to read the MAC
address from the standard location in device tree.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This is easier to deal with and works just as well for this simple
function.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Tegra186 build are currently dealt with in very special ways, which is
because Tegra186 is fundamentally different in many respects. It is no
longer necessary to do many of the low-level programming because early
boot firmware will already have taken care of it.
Unfortunately, separating Tegra186 builds from the rest in this way
makes it difficult to share code with prior generations of Tegra. With
all of the low-level programming code behind Kconfig guards, the build
for Tegra186 can again be unified.
As a side-effect, and partial reason for this change, other Tegra SoC
generations can now make use of the code that deals with taking over a
boot from earlier bootloaders. This used to be nvtboot, but has been
replaced by cboot nowadays. Rename the files and functions related to
this to avoid confusion. The implemented protocols are unchanged.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Commit 86cf1c8285 ("configs: Migrate CONFIG_NR_DRAM_BANKS") reduced
the number of DRAM banks supported by U-Boot from 1026 to 8 on P2771-000
boards.
However, as explained in commit a9819b9e33 ("ARM: tegra: p2771-000:
increase max DRAM bank count"), the platform can have a large number of
unusable chunks of memory (up to 1024), so a total of 1026 DRAM banks
are needed to describe the worst-case situation.
In practice the number of DRAM banks needed will typically be much
lower, but we should be prepared to properly deal with the worst case.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Resetting the USB device controller on boot is only necessary if the SoC
actually has a UDC controller and U-Boot enables support for it. All the
Tegra boards support UDC via the ChipIdea UDC driver, so make the UDC on
boot workaround depend on the ChipIdea UDC driver.
This prevents a crash on Tegra186 which does not have the ChipIdea UDC.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Some devices may restrict access to the PMC to TrustZone software only.
Non-TZ software can detect this and use SMC calls to the firmware that
runs in the TrustZone to perform accesses to PMC registers.
Note that this also fixes reset_cpu() and the enterrcm command on
Tegra186 where they were previously trying to access the PMC at a wrong
physical address.
Based on work by Kalyani Chidambaram <kalyanic@nvidia.com> and Tom
Warren <twarren@nvidia.com>.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Boards may not support all the boot target devices in the default list
for Tegra devices. Allow a board to override the list and default to the
standard list only if the board hasn't specified one itself.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The save_boot_params() function takes as its first four arguments the
first four registers. On 32-bit ARM these are r0, r1, r2 and r3, all of
which are 32 bits wide. However, on 64-bit ARM thene registers are x0,
x1, x2 and x3, all of which are 64 bits wide. In order to allow reusing
the save_boot_params() implementation on 64-bit ARM, change it to take
unsigned long parameters rather than the fixed size 32-bit integers.
This ensures that the correct values are passed.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Powergate code is not relevant on all Tegra SoC generations, so guard it
with a Kconfig symbol that can be selected by the generations that need
it.
This is in preparation for unifying Tegra186 code with the code used on
older generations.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Pin controller code is not relevant on all Tegra SoC generations, so
guard it with a Kconfig symbol that can be selected by the generations
that need it.
This is in preparation for unifying Tegra186 code with the code used on
older generations.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Memory controller code is not relevant on all Tegra SoC generations, so
guard it with a Kconfig symbol that can be selected by the generations
that need it.
This is in preparation for unifying Tegra186 code with the code used on
older generations.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The GP pad control code is not relevant on all Tegra SoC generations, so
guard it with a Kconfig symbol that can be selected by the generations
that need it.
This is in preparation for unifying Tegra186 code with the code used on
older generations.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Clock code is not relevant on all Tegra SoC generations, so guard it
with a Kconfig symbol that can be selected by the generations that need
it.
This is in preparation for unifying Tegra186 code with the code used on
older generations.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
There's no need to replicate the pmu.h header file for every Tegra SoC
generation. Use a single header that is shared across generations.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
pll_c is not a valid parent for the disp1 clock, so trying to set it
will fail. Given that display is not used in U-Boot, remove the init
table entry so that disp1 will keep its default parent (clk_m).
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
On Tegra210 the parents for the disp1 and disp2 clocks are slightly
different from earlier chips. Only pll_p, pll_d_out0, pll_d2_out0 and
clk_m are valid parents (technically pll_d_out is as well, but U-Boot
doesn't know anything about it). Fix up the type name and the mux
definition.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This function can be used to set the local MAC address for the default
Ethernet interface in its device tree node. The default interface is
identified by the "ethernet" alias.
One case where this is useful is for devices that store their MAC
address in a custom location. Once extracted, board code can store the
MAC address in U-Boot's control DTB so that it will automatically be
used by the Ethernet uclass.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
current implementation for checking if "led list"
command is called checks only if "l" is passed to the
led command. This prevents switching leds with name
which starts also with a "l". So check for passing
"list".
While at it, also fix a typo in led command usage.
Signed-off-by: Heiko Schocher <hs@denx.de>
This is required for proper operation of the 8-bit data transfers.
This fixes transient errors seen on BeagleBone Black.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
There are no more users of lowlevel_init.S. Remove the file.
Suggested-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
This adds a define for CONFIG_SKIP_LOWLEVEL_INIT in the legoev3 config.
On the EV3, U-Boot is loaded into RAM by another bootloader, so we
don't need the lowlevel init in U-Boot.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The MAC address is located at at the last 64K of SPI Flash, and
it's 6 bytes long. This patch corrects both the length and
starting byte of the MAC address.
Signed-off-by: Adam Ford <aford173@gmail.com>
The commong initialization code manually initializes the GPIO
even when OF_CONTROL does it, so we can reduce the code size a
bit by not doing it manually when we have device tree support.
Using the omap3_logic board (dm3730), the sizes shrunk:
Before:
text data bss dec hex filename
561066 28596 116880 706542 ac7ee u-boot
55245 1605 1888 58738 e572 spl/u-boot-spl
After
text data bss dec hex filename
560898 28548 116872 706318 ac70e u-boot
55121 1557 1888 58566 e4c6 spl/u-boot-spl
Signed-off-by: Adam Ford <aford173@gmail.com>
With ipam390 support removed in we can remove the reference to the
linker script since that case will never be true.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
U-Boot README recommends initializing SDRAM in board_init_f(). DA850
was doing it as part of board_init_r() (through call to spl_board_init()
which calls arch_cpu_init() which calls da850_ddr_setup())
This worked fine till commit 15b8c75058 ("davinci:
da850evm/omapl138-lcdk: Move BSS to SDRAM because SRAM is full") moved
BSS to SDRAM.
Functions like mmc_initialize() called in board_init_r() assume BSS is
available. Since SDRAM was not initialized when arch/arm/lib/crt0.S tried
to initialize BSS to 0, BSS is not initialized correctly.
Fix this by simply calling arch_cpu_init() from board_init_f(). Also move
preloader_console_init() there to help debug issues with board_init_r().
With this spl_board_init() is no longer needed, we remove it.
Tested using MMC/SD boot on OMAP-L138 LCDK board.
Tested-by: Adam Ford <aford173@gmail.com> #da850evm
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Tested-by: Peter Howard <phoward@gme.net.au> #omapl138_lcdk
commit 21af33ed03 ("ARM: davinci: omapl138_lcdk: Enable DM_MMC")
wanted to enable DM_MMC only for U-Boot and not for SPL.
But CONFIG_DM_MMC is defined for SPL build too. Because of this
MMC device was not getting registered for SPL causing MMC/SD
boot breakage.
Instead use CONFIG_IS_ENABLED(DM_MMC) which will remain false until
CONFIG_SPL_DM_MMC is defined.
Tested-by: Adam Ford <aford173@gmail.com> #da850evm
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Tested-by: Peter Howard <phoward@gme.net.au> #omapl138_lcdk
- Support Microchip MPFS Icicle board.
- Enable e1000 and nvme support for qemu.
- Enable PCI host ECAM generic driver for qemu.
- Increase the environment size to 128kB for qemu.
Some boards don't have such a regulator, and don't need one to enable
HDMI display. Make it optional, fixing hdmi display for those boards.
Also surround the regulator code with a config check on DM_REGULATOR.
Reported-by: Mohammad Rasim <mohammad.rasim96@gmail.com>
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Mohammad Rasim <mohammad.rasim96@gmail.com>
This patch adds Microchip MPFS Icicle board support.
For now, NS16550 serial driver is only enabled.
The Microchip MPFS Icicle defconfig by default builds
U-Boot for M-Mode with SMP support.
Signed-off-by: Padmarao Begari <padmarao.begari@microchip.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Since we have added the PCI support to the 'virt' target, enable
e1000 and NVME as alternate network and storage devices for these
virtio based devices.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Tested-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
The existing default size of 4kB is too small as the default environment
has already nearly that size and defining a single additional environment
variable can exceed the available space.
Signed-off-by: Karsten Merker <merker@debian.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
With this option, -nv, at "setenv -e" command, a variable will be defined
as non-volatile.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Boot####, BootOrder and BootNext should be non-volatile.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The attribute, EFI_VARIABLE_NON_VOLATILE, should be encoded as "nv" flag
in U-Boot variable if specified.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Extend the driver to build with DM_VIDEO enabled. DTS files
must additionally include 'u-boot,dm-pre-reloc' property in
soc and child nodes to enable driver binding to mxsfb device.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Refactor video_hw_init() function, and introduce an independent function
for the common procedure of initialization.
Currently video_hw_init() is only in charge of parsing configuration from
env("videomode") and filling struct GraphicPanel, and new
mxs_probe_common() does hw specific initialization (invocation of
mxs_lcd_init() etc.)
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Provide directly framebuffer address instead of pointer to
GraphicDevice struct, which will let to re-use this function in
DM_VIDEO configurations.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Enable CONFIG_SYS_WHITE_ON_BLACK by default for DM_VIDEO enabled
configurations, where env("splashimage") is used for showing Toradex
boot logo.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
