The ACPI tables are special in that they are passed to EFI as a separate
piece, independent of other tables.
Also they can be spread over two areas of memory, e.g. with QEMU we end
up with tables kept in high memory as well.
Add new global_data fields to hold this information and update the bdinfo
command to show the table areas.
Move the rom_table_end variable into the loop that uses it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Once the ACPI tables have been set up, record their address so that it is
possible to list them with 'acpi list'.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
On the imx8ulp A1 SoC, the ELE RNG needs to be manually started.
Signed-off-by: Clement Faure <clement.faure@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Extend the RX timeout value to 10s, because when authentication is failed
the ELE needs long time (>2s for 28M image) to return the result. Print
rx wait info per 1s.
Also correct TX and RX status registers in debug.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
According to SRM, the Sentinel MU has 8 TR and 4 RR registers. All
of them are used for ELE message. So update TR count to 8 and fix a
typo in receive msg
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add two ELE API: ele_return_lifecycle_update and ele_write_secure_fuse
Add two cmd: ahab_return_lifecycle and ahab_sec_fuse_prog
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Per NXP requirement, we rename all the NXP EdgeLock Secure Enclave
code including comment, folder and API name to ELE to align.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Move imx8 sci header file to include/firmware/imx, then we could
use build macro to reuse some i.MX8 drivers for i.MX9, such as
drivers/cpu/imx8_cpu.c.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Stefano Babic <sbabic@denx.de>
ESM MCU masks must be set to 0h so that PMIC can handle errors
that require attention for example SYS_SAFETY_ERRn. The required bits
must be cleared: ESM_MCU_RST_MASK, ESM_MCU_FAIL_MASK, ESM_MCU_PIN_MASK.
If PMIC expected to handle errors, make sure EVM is configured to
connect SOC_SAFETY_ERRz (Main) to the PMIC.
Note that even though the User Guide for TPS65941 for J721E mentions
that these bits are reset to 0h; it is not reflected once board boots to
kernel, possibly due to NVM configurations. Eithercase, it is best to
account for this from R5 SPL side as well.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
This change adds a Qualcomm GENI SE QUP device driver as a wrapper for
actually enabled and used serial devices found on a board.
At the moment the driver is pretty simple, its intention is to populate
childred devices and provide I/O mem read interface to them as clients,
this is needed for GENI UART driver to set up a proper clock divider
and provide the actually asked baud rate.
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
The documentation for misc_read() says:
Return: number of bytes read if OK (may be 0 if EOF), -ve on error
The Rockchip efuse driver implements this so it should return the number
of bytes read rather than zero on success. Fix this so that the driver
follows the usual contract for read operations.
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The documentation for misc_read() says:
Return: number of bytes read if OK (may be 0 if EOF), -ve on error
The Rockchip efuse driver implements this so it should return the number
of bytes read rather than zero on success. Fix this so that the driver
follows the usual contract for read operations.
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The DM_REGULATOR symbol has SPL counterpart in:
drivers/power/regulator/Kconfig:config SPL_DM_REGULATOR
Use CONFIG_IS_ENABLED() macro to match on the correct
variant depending on the build stage.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
---------------------------------
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/15819
i.MX patches queued for next:
- Conversions to DM_SERIAL
- Fixes for Toradex boards
- Gateworks Boards
- i.MX8ULP
- EQoS support / fixes, changes in boards
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQS2TmnA27QKhpKSZe309WXkmmjvpgUCZCaU0Q8cc2JhYmljQGRl
bnguZGUACgkQ9PVl5Jpo76YCKgCgk4OueoIggmes+Ccj8bu1BcQbrfYAoJAgMeKE
It0hrVAifD62TPb2rmHt
=hFVG
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-next-20230331' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx into next
u-boot-imx-next-20230331 for next
---------------------------------
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/15819
i.MX patches queued for next:
- Conversions to DM_SERIAL
- Fixes for Toradex boards
- Gateworks Boards
- i.MX8ULP
- EQoS support / fixes, changes in boards
Reports the sandbox swapcase PCI Express device to support a 256 byte
Maximum Payload Size for MPS tuning tests.
Signed-off-by: Stephen Carlson <stcarlso@linux.microsoft.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The ocotp driver is available for regular and SPL builds using the
(SPL_)MXC_OCOTP configuration. Also, the ocotp driver does not support
the driver model (DM) configuration.
But, for SPL builds, the SPL_MXC_OCOTP configuration depends on
SPL_MISC which implies on SPL_DM.
This commit replaces the dependency on SPL_MISC with SPL_DRIVERS_MISC.
So the only requirement is to have enabled miscellaneous drivers for
the SPL.
Signed-off-by: Jean-Marie Lemetayer <j.lemetayer@kerlink.fr>
Remove legacy command definitions, change to use new ELE_xxx command
request.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Add get_events API to retrieve any singular events that has occurred
since the FW has started from sentinel
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The ECC fuse on 8ULP can't be written twice. If any user did it, the
ECC value would be wrong then cause accessing problem to the fuse.
The patch will lock the ECC fuse word to avoid this problem.
For iMX9, the OTP controller automatically prevents an ECC fuse word to
be written twice. So it does not need the setting.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Since new 8ULP A1 S400 FW (v0.0.8-e329b760) can support to read
more fuses: like PMU trim, Test flow/USB, GP1-5, GP8-10. Update
the u-boot driver for the new mapping.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Alice Guo <alice.guo@nxp.com>
Add support for rk3066a, rk3188, rk322x and rk3288 compatible.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Refactor the driver to use driver data and ops to simplify handling
of SoCs that require a unique read op.
Move handling of the aligned bounce buffer to main read op in order to
keep the SoC unique read op simple.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add a simple debug command to dump the content of the otp.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add support for rk3588 compatible.
Adjust offset using driver data in main read op.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add support for rk3568 compatible.
Handle allocation of an aligned bounce buffer in main read op in order
to keep the SoC unique read op simple.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Refactor the driver to use driver data and ops to simplify handling
of SoCs that require a unique read op.
Use readl_poll_sleep_timeout instead of a custom poll loop, and add
validation of input parameter to main read op.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This converts 1 usage of this option to the non-SPL form, since there is
no SPL_A003399_NOR_WORKAROUND defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a bootdev device for qfw so that it can be used with standard boot.
This simply checks for the correct method and then does the read. Most of
the other logic is handed in a new bootmeth driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Unlike in Linux, -supply is not automatically appended to regulator
requests. Add it.
Fixes: 2645bc0e12 ("arm: layerscape: Add sfp driver")
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
SCFW has fixed a overflow issue in sc_rm_is_pad_owned API. This
requires u-boot to update API implementation, since it will cause
compatible issue. Otherwise all pad checking will have problem and
cause pad setting not continue.
Due to the compatible issue, the new u-boot only works with new
SCFW (API version: 1.21 and later).
old scfw + old u-boot: API overflow issue
old scfw + new u-boot, or new scfw + old u-boot: API compatible issue
new scfw + new u-boot: Working
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by : Jason Liu <Jason.hui.liu@nxp.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
At this point, the remaining places where we have a symbol that is
defined as CONFIG_... are in fairly odd locations. While as much dead
code has been removed as possible, some of these locations are simply
less obvious at first. In other cases, this code is used, but was
defined in such a way as to have been missed by earlier checks. Perform
a rename of all such remaining symbols to be CFG_... rather than
CONFIG_...
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The fs_loader device is used to pull in settings via the chosen node.
However, there was no library function for this, so arria10 was doing it
explicitly. This function subsumes that, and uses ofnode_get_chosen_node
instead of navigating the device tree directly. Because fs_loader pulls
its config from the environment by default, it's fine to create a device
with nothing backing it at all. Doing this allows enabling
CONFIG_FS_LOADER without needing to modify the device tree.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
At this point in the conversion there should be no need to have logic to
disable some symbol during the SPL build as all symbols should have an
SPL counterpart.
The main real changes done here are that we now must make proper use of
CONFIG_IS_ENABLED(DM_SERIAL) rather than many of the odd tricks we
developed prior to CONFIG_IS_ENABLED() being available.
Signed-off-by: Tom Rini <trini@konsulko.com>
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS namespace do
not easily transition to Kconfig. In many cases they likely should come
from the device tree instead. Move these out of CONFIG namespace and in
to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_NUM
namespace do not easily transition to Kconfig. In many cases they likely
should come from the device tree instead. Move these out of CONFIG
namespace and in to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The device tree binding [1] specify the vendor-id, product-id, device-id
and language-id as 16 bit values and the linux driver reads the boost-up
value as 8 bit value.
[1] https://www.kernel.org/doc/Documentation/devicetree/bindings/usb/usb251xb.txt
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Reviewed-by: Marek Vasut <marex@denx.de>