The Libretech ALL-H3-CC has a high density connector for attaching
an eMMC module. The module form factor and connection is specific
to Libretech, and has provisions for split vmmc/vqmmc (core and I/O)
voltage supplies, but this board does not wire the vqmmc side. The
H2+/H3/H5 SoCs do not support alternate I/O voltages for eMMC either.
Only 3.3V is supported. A specific module that ties vqmmc to vmmc,
with both at 3.3V, must be used.
Given that a) eMMC is not designed to be hotplugged, b) power is
always provided on the pins, and c) MMC controllers can deal with
missing cards, we can enable this by default. If a module is attached
it will be picked up by the system.
The device tree change was also submitted to the Linux Kernel and
has already been queued up for 4.19.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This patch adds qspi driver support for all ZynqMP ZCU102
boards.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Enable the gigabit ethernet for the Bananapi M2 Ultra board.
Tested on BananaPi M2 Berry (R40), custom board (V40)
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Lothar Felten <lothar.felten@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
Add a device tree node for the Allwinner R40/V40 GMAC gigabit
ethernet interface.
The R40 SoC does not use the syscon register for GMAC settings.
The gigabit ethernet interface can only be routed to a fixed set of
pins.
Updated to match the Linux kernel's device tree.
Signed-off-by: Lothar Felten <lothar.felten@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
When the defconfig for the SoPine baseboard was added, there wasn't any
proper DT for the board yet, so we used the Pine64 DT as a placeholder.
Copy the DT file(s) meanwhile added in Linux over to U-Boot, and use
them in our defconfig.
This is as of v4.18-rc3, exactly Linux commit:
commit 7d556bfc49adddf2beb0d16c91945c3b8b783282
Author: Jagan Teki <jagannadh.teki@gmail.com>
Date: Mon Dec 4 10:23:07 2017 +0530
arm64: allwinner: a64-sopine: Fix to use dcdc1 regulator instead of vcc3v3
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Update the .dts file for the various boards with an Allwinner H3 SoC.
This is as of v4.18-rc3, exactly Linux commit:
commit 721afaa2aeb860067decdddadc84ed16f42f2048 (HEAD)
Merge: 7c00e8ae041b 87815dda5593
Author: Linus Torvalds <torvalds@linux-foundation.org>
Date: Mon Jun 11 17:57:38 2018 -0700
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
This also includes the OrangePi Zero .dts, which technically has an
Allwinner H2+ SoC.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Update the .dts file for the various boards with an Allwinner H5 SoC.
This is as of v4.18-rc3, exactly Linux commit:
commit af5d05bdc99c211729cba0a3d5417bccfa308caf
Author: Neil Armstrong <narmstrong@baylibre.com>
Date: Tue Apr 24 13:47:14 2018 +0200
arm64: dts: allwinner: Add dts file for Libre Computer Board ALL-H3-CC H5 ver.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Update the device tree files from the Linux tree as of v4.18-rc3,
exactly Linux commit:
commit 55c5ba5e49a0a124ed416880e8227b493474495e
Author: Chen-Yu Tsai <wens@csie.org>
Date: Tue Apr 24 19:34:22 2018 +0800
arm64: dts: allwinner: h5: Add cpu0 label for first cpu
Since the H3 and H5 are very similar (aside from the actual ARM cores),
they share most the SoC .dtsi and thus have to be updated together.
One tiny change is the removal of the "arm/" prefix from the include
path in the sun50i-h5.dtsi, which is needed because we don't share the
same sophisticated DT directory layout of Linux.
Also we need to fix up the board .dts files already, since the .dtsi
removes some pins, so the .dts can't reference them anymore. This is to
maintain bisectability.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Update the .dts files for the various boards with an Allwinner A64 SoC.
This is as of v4.18-rc3, exactly Linux commit:
commit 818668055c9d588c9a9d151e3b258ed1adacba0b
Author: Jagan Teki <jagan@amarulasolutions.com>
Date: Mon Apr 23 12:02:39 2018 +0530
arm64: dts: allwinner: a64: bananapi-m64: add usb otg
It updates the existing DT files, adds the newly added axp803.dtsi and
removes our temporary kludge file to get Ethernet support in U-Boot.
I left the amarula-relic alone, as this DT has not reached mainline yet.
The changes are not critical anyway, and the next sync will fix this.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Updates the device tree file from the the Linux tree as of v4.18-rc3,
exactly Linux commit:
commit c1cff65f9b16b31e731e2e75bbe06638c86e1996
Author: Harald Geyer <harald@ccbib.org>
Date: Thu Mar 15 16:25:08 2018 +0000
arm64: dts: allwinner: a64: add simplefb for A64 SoC
This also pulls in the newly required include files for the clock and
reset bindings, also removes the now redundant part from our
*-u-boot.dtsi overlay file.
I kept the PWM node from U-Boot, as we recently gained this explicitly
for U-Boot's own usage and I don't want to regress here. This node is in
the queue for mainline Linux already, so the next sync will make it all
equal again.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Commit 5dfd5607af2114047bd ("ARM: socfpga: Pull DRAM size from DT") get
memory size from DT. So, we need to update memory size in memory node.
Otherwise, it cause U-boot hang.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
The SPL can also parse the DRAM configuration node to figure out the
memory layout, make sure it is available.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
This commit adds uCRobotics Bubblegum-96 board support. This board is
one of the 96Boards Consumer Edition platform based on Actions Semi
S900 SoC.
Features:
- Actions Semi S900 SoC (4xCortex A53, Power VR G6230 GPU)
- 2GiB RAM
- 8GiB eMMC, uSD slot
- WiFi, Bluetooth and GPS module
- 2x Host, 1x Device USB port
- HDMI
- 20-pin low speed and 40-pin high speed expanders, 6 LED, 3 buttons
U-Boot will be loaded by ATF at EL2 execution level. Relevant driver
support will be added in further commits.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
This commit adds Actions Semi OWL SoC family support with S900 as the
first target SoC.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The various Aries Embedded boards have been orphaned for a year and no
one has come forward to take care of them. Remove.
Signed-off-by: Tom Rini <trini@konsulko.com>
fdt_file is looking for imx6ul-geam-kit.dtb but Linux
has imx6ul-geam.dtb, since Linux skipped -kit on file name
by below commit.
"ARM: dts: imx6ul-geam: Skip suffix -kit from dts name"
(sha1: 182de5ebce71e469cfa686fcdf08c9cbe11ece97)
So, due to this mismatch U-Boot failed to pick the
proper dtb which eventually break the Linux boot.
This patch fixed this mismatch by
- renaming dts files
- update config option to use new dtb file
- update fdt_file to new dtb file name
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Now that the clock-frequency information has been moved to the
driver, more DT sync is possible.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add regulator nodes and pinmux settings to the SDHI3 on E3 Ebisu
and enable HS200 mode on it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Both the RAVB and SH ether driver now support parsing the PHY reset
GPIOs from both the PHY nodes and the MAC nodes, move the reset GPIOs
back into the PHY nodes to minimize DT difference between U-Boot and
Linux.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The current state of RAVB driver expects the PHY reset GPIO in the
RAVB mode, move it back from the PHY node to avoid breakage.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Follow Linux commit 10b62a2f785a (".gitignore: move *.dtb and *.dtb.S
patterns to the top-level .gitignore").
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This patch prevents from the situation where we may end up with garbage
displayed on the LCD panel.
Such situation occurs when one performs "reboot -f" in Linux and then
stop in U-boot (or observe the garbage on the screen during boot up).
To prevent from such situation - the PWM pin is configured as GPIO and set
to LOW.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Orange Pi Zero Plus is an open-source single-board computer
using the Allwinner H5 SOC.
H5 Orangepi Zero Plus has
- Quad-core Cortex-A53
- 512MB DDR3
- micrSD slot
- 16MBit SPI Nor flash
- Debug TTL UART
- 1GBit/s Ethernet (RTL8211E)
- Wifi (RTL8189FTV)
- USB 2.0 Host
- USB 2.0 OTG + power supply
The device tree file is copied from the Linux kernel 4.17.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Orange Pi R1 is an open-source single-board computer using the
Allwinner H2+ SOC.
H2+ Orange Pi R1 has
- Quad-core Cortex-A7
- 256MB DDR3
- micrSD slot
- 128MBit SPI Nor flash
- Debug TTL UART
- 100MBit/s Ethernet (H2+)
- 100MBit/s Ethernet (RTL8152B)
- Wifi (RTL8189ETV)
- USB 2.0 OTG + power supply
This board is very similar to the Orange Pi Zero.
The device tree file is copied from the Linux kernel 4.17.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Add EtherAVB PHY reset on V3M Eagle to let the AVB driver unreset the PHY.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add EtherAVB pinmux node on V3M Eagle to set the pinmux configuration.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add device tree nodes for the Renesas RPC HF/QSPI controller
to R8A77990 E3.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
dtc is showing some warnings and this change was also done in
the Linux kernel as "Input: gpio-keys - clean up device tree binding
example"
with this fragment in commit message
"Drop #address-cells and #size-cells, which are not required by the
gpio-keys binding documentation, as button sub-nodes are not devices."
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch splits the current mini emmc configuration into emmc0
and emmc1 configurations because emmc is probed at boot time and on
systems which have only one interface mini configuration is failing on
unused interface. This patch also adds required clock node in dts and
enables CONFIG_MMC_SDHCI_ZYNQ through defconfig.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Synchronize the Linux Device Tree for Amlogic Meson GX boards from Linux 4.17.0
This will enable USB on Amlogic Meson GXL Boards like Khadas VIM, P212 or
LibreTech-CC.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
