Commit graph

80017 commits

Author SHA1 Message Date
Aswath Govindraju
36dafd8045 arm: mach-k3: am6_init: Fix the path and value's length in the fixup performed for usb boot
The node name of the bus in the device tree has changed. Also, the length
argument to be passed should be the length of new value. Therefore, fix the
path to usb device tree node as well as the length argument passed.

Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
2022-06-10 13:37:32 -04:00
Aswath Govindraju
750d8470cb arm: dts: k3-am654-r5-base-board: Fix the dt properties in usb0 instance
For dfu boot mode, the clocks property needs to be deleted and dr_mode
needs to be set to peripheral. Therefore, add the required fixes for the
same.

Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
2022-06-10 13:37:32 -04:00
Masahisa Kojima
f81aaa0b33 spi: synquacer: simplify tx completion checking
There is a TX-FIFO and Shift Register empty(TFES) status
bit in spi controller. This commit checks the TFES bit
to wait the TX transfer completes.

Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Signed-off-by: Satoru Okamoto <okamoto.satoru@socionext.com>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>
2022-06-10 13:37:32 -04:00
Masahisa Kojima
de9f2c9c2e spi: synquacer: DMSTART bit must not be set while transferring
DMSTART bit must not be set while there is active transfer.
This commit sets the DMSTART bit only when the transfer begins.

Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Signed-off-by: Satoru Okamoto <okamoto.satoru@socionext.com>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>
2022-06-10 13:37:32 -04:00
Masahisa Kojima
88d50ed8a1 spi: synquacer: wait until slave is deselected
synquacer_cs_set() function does not wait the chip select
is deasserted when the driver sets the DMSTOP to deselect
the slave.
This commit checks the Slave Select Released(SRS) bit to wait
until the slave is deselected.

Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Signed-off-by: Satoru Okamoto <okamoto.satoru@socionext.com>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>
2022-06-10 13:37:32 -04:00
Masahisa Kojima
29d382b94e spi: synquacer: busy variable must be initialized before use
"busy" variable is ORed without being initialized,
must be zeroed before use.

Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Signed-off-by: Satoru Okamoto <okamoto.satoru@socionext.com>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>
2022-06-10 13:37:32 -04:00
Jim Liu
f49d616bea pinctrl: nuvoton: Add NPCM7xx pinctrl driver
Add Nuvoton BMC NPCM750 Pinmux and Pinconf support.

Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
2022-06-10 13:37:32 -04:00
Derald D. Woods
d7116ca1d0 ARM: omap3: evm: Fix 'fitImage' booting
This commit sets two additional variables in the default BOOTCOMMAND.
Adding 'boot=mmc' and 'addr_fit=0x8b000000' removes the need for a
special 'uEnv.txt' to be created. The 'addr_fit' variable is the key
piece here. It is normally defined as 0x90000000, in the macro
DEFAULT_FIT_TI_ARGS. For this OMAP34XX board, 0x8b000000 works without
touching other varibles. This was tested with a 'fitImage' created
using the following FIT source:

----------------------------------------------------------------------
/dts-v1/;

/ {
	description = "Simple image with single Linux kernel and FDT blob";
	#address-cells = <1>;

	images {
		kernel {
			description = "Linux kernel: omap2plus";
			data = /incbin/("./zImage");
			type = "kernel";
			arch = "arm";
			os = "linux";
			compression = "none";
			load = <0x80008000>;
			entry = <0x80008000>;
			hash-1 {
				algo = "sha256";
			};
		};
		fdt-omap3-evm.dtb {
			description = "FDT: omap3-evm.dtb";
			data = /incbin/("./omap3-evm.dtb");
			type = "flat_dt";
			arch = "arm";
			compression = "none";
			load = <0x8ff00000>;
			hash-1 {
				algo = "sha256";
			};
		};
	};

	configurations {
		default = "conf-omap3-evm.dtb";
		conf-omap3-evm.dtb {
			description = "Boot Linux kernel with FDT blob";
			kernel = "kernel";
			fdt = "fdt-omap3-evm.dtb";
		};
	};
};
----------------------------------------------------------------------

Additionally, the default environment is now stored in "uboot.env" on
the FAT partition of MMC '0'.

Fixes: 11e2ab3f0b ("ARM: omap3: evm: Enable booting 'fitImage' with DEFAULT_FIT_TI_ARGS")
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
2022-06-10 13:37:32 -04:00
Derald D. Woods
25d629b603 ARM: omap3: evm: Complete DM_I2C migration
This commits enables DM_I2C and sets the default bus to 0.

Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
2022-06-10 13:37:32 -04:00
Derald D. Woods
161535444b ARM: omap3: evm: Power on MMC when setting up PMIC
This commit copies the related code changes from the BeagleBoard.

Reference:
- 848cfe098f

Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
2022-06-10 13:37:32 -04:00
William Zhang
f8209d3051 arm: bcmbca: introduce the bcmbca architecture and 47622 SOC
This is the initial support for Broadcom's ARM-based 47622 SOC.

In this change, our first SOC is an armv7 platform called 47622. The
initial support includes a bare-bone implementation and dts with ARM
PL011 uart.

The SOC-specific code resides in arch/arm/mach-bcmbca/<soc> and board
related code is in board/broadcom/bcmba.

The u-boot image can be loaded from flash or network to the entry
point address in the memory and boot from there.

Signed-off-by: William Zhang <william.zhang@broadcom.com>
Signed-off-by: Kursad Oney <kursad.oney@broadcom.com>
Signed-off-by: Anand Gore <anand.gore@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
2022-06-10 13:37:32 -04:00
Vaishnav Achath
d7ef2ef7c8 configs: j721e_evm_defconfig: Add HBMC related configs
Enable HBMC and HyperFlash in R5SPL, A72 SPL and A72 U-Boot

Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
[trini: Update j721e_hs_evm_a72 as well]
Signed-off-by: Tom Rini <trini@konsulko.com>
2022-06-10 13:36:58 -04:00
Vaishnav Achath
66a33f41e9 ti: j721e: enable hyperflash spl fixup for j721e
On j721e, its not possible to use OSPI0 and HBMC simultaneously as they
are muxed within the Flash Subsystem hence disable HBMC by default and
keep OSPI enabled. Bootloader will fixup DT when it detects HyperFlash
mux selection instead of OSPI.

Also updated detect_enable_hyperflash to use correct GPIO when checking
hypermux selection state:
* J7200 - hypermux sel connected to WKUP_GPIO0_6
* J721E - hypermux·sel·connected·to·WKUP_GPIO0_8

Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
2022-06-10 09:03:22 -04:00
Vaishnav Achath
d45ccab483 configs: j721e_evm.h: define CONFIG_SYS_FLASH_BASE
Define CONFIG_SYS_FLASH_BASE to indicate start address of
Flash memory

Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
2022-06-10 09:03:22 -04:00
Vaishnav Achath
09d14d7f10 arm: k3: sysfw-loader: add hyperflash support
add support for loading system firmware from hyperflash.

Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
2022-06-10 09:03:22 -04:00
Vaishnav Achath
8fceb0edf4 arm: dts: k3-j721e-common-proc-board: enable hyperflash mux sel GPIO
Add wkup_gpio pinmux setting which will be used for performing the
DT fixup for hbmc node according to mux selection state, on J721E
EVM, hypermux sel is tied to ·WKUP_GPIO0_8.

Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
2022-06-10 09:03:22 -04:00
Vaishnav Achath
fa4f5aabae arm: dts: k3-j721e-common-proc-board-u-boot: enable HyperFlash in SPL
add u-boot,dm-spl pre-relocation property to enable hbmc in SPL.

Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
2022-06-10 09:03:22 -04:00
Vaishnav Achath
30426492d3 arm: dts: k3-j721e-r5-common-proc-board: Add HyperFlash node
J721e SoM as a 64MB HyperFlash on board. Add pinmux and DT node
for the same.

Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
2022-06-10 09:03:22 -04:00
Vaishnav Achath
cbd7790a69 arm: dts: k3-j721e-som-p0: Add HyperFlash node
J721e SoM as a 64MB HyperFlash on board. Add pinmux and DT node
for the same.

Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
2022-06-10 09:03:22 -04:00
Vaishnav Achath
297daac43a arm: dts: k3-j721e-mcu-wakeup: Add HyperBus Controller node
Add DT node for HyperBus Memory Controller and hbmc-mux in the
FSS. hbmc-am654 driver uses syscon_get_regmap() call which fails
with current compatible setting.

Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
2022-06-10 09:03:22 -04:00
Tom Rini
e5028bb227 Merge branch '2022-06-09-add-support-for-nvmem-api' into next
To quote the author:
This adds support for the nvmem-cells properties cropping up in manyb
device trees. This is an easy way to load configuration, version
information, or calibration data from a non-volatile memory source. For
more information, refer to patch 6 ("misc: Add support for nvmem
cells").

For the moment I have only added some integration tests using the
ethernet addresses. This hits the main code paths (looking up nvmem
cells) but doesn't test writing. I can add a few stand-alone tests if
desired.
2022-06-09 15:20:11 -04:00
Sean Anderson
3f51ba926b test: Load mac address using misc device
This loads a mac address using a misc device using the nvmem interface.

Signed-off-by: Sean Anderson <sean.anderson@seco.com>
2022-06-08 14:00:22 -04:00
Sean Anderson
d3f7287849 test: Load mac address using RTC
This uses the nvmem API to load a mac address from an RTC.

Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2022-06-08 14:00:22 -04:00
Sean Anderson
472caa69e3 test: Load mac address with i2c eeprom
This uses an i2c eeprom to load a mac address using the nvmem interface.
Enable I2C_EEPROM for sandbox SPL since it is the only sandbox config
which doesn't enable it eeprom.

Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2022-06-08 14:00:22 -04:00
Sean Anderson
97d0f9bfdd net: Add support for reading mac addresses from nvmem cells
This adds support for reading mac addresses from the "mac-address" nvmem
cell. If there is no (local-)mac-address property, then we will try
reading from an nvmem cell.

For some existing examples of this property, refer to imx8mn.dtsi and
imx8mp.dtsi. Unfortunately, fuse drivers have not yet been converted
to DM.

Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2022-06-08 14:00:22 -04:00
Sean Anderson
185d3db7be sandbox: Enable NVMEM
This enables NVMEM for all sandbox defconfigs, enabling it to be used in
unit tests in the next few commits.

Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2022-06-08 14:00:22 -04:00
Sean Anderson
c8ce7ba87d misc: Add support for nvmem cells
This adds support for "nvmem cells" as seen in Linux. The nvmem device
class in Linux is used for various assorted ROMs and EEPROMs. In this
sense, it is similar to UCLASS_MISC, but also includes
UCLASS_I2C_EEPROM, UCLASS_RTC, and UCLASS_MTD. New drivers corresponding
to a Linux-style nvmem device should be implemented as one of the
previously-mentioned uclasses. The nvmem API acts as a compatibility
layer to adapt the (slightly different) APIs of these uclasses. It also
handles the lookup of nvmem cells.

While nvmem devices can be accessed directly, they are most often used
by reading/writing contiguous values called "cells". Cells typically
hold information like calibration, versions, or configuration (such as
mac addresses).

nvmem devices can specify "cells" in their device tree:

	qfprom: eeprom@700000 {
		#address-cells = <1>;
		#size-cells = <1>;
		reg = <0x00700000 0x100000>;

		/* ... */

		tsens_calibration: calib@404 {
			reg = <0x404 0x10>;
		};
	};

which can then be referenced like:

	tsens {
		/* ... */
		nvmem-cells = <&tsens_calibration>;
		nvmem-cell-names = "calibration";
	};

The tsens driver could then read the calibration value like:

	struct nvmem_cell cal_cell;
	u8 cal[16];
	nvmem_cell_get_by_name(dev, "calibration", &cal_cell);
	nvmem_cell_read(&cal_cell, cal, sizeof(cal));

Because nvmem devices are not all of the same uclass, supported uclasses
must register a nvmem_interface struct. This allows CONFIG_NVMEM to be
enabled without depending on specific uclasses. At the moment,
nvmem_interface is very bare-bones, and assumes that no initialization
is necessary. However, this could be amended in the future.

Although I2C_EEPROM and MISC are quite similar (and could likely be
unified), they present different read/write function signatures. To
abstract over this, NVMEM uses the same read/write signature as Linux.
In particular, short read/writes are not allowed, which is allowed by
MISC.

The functionality implemented by nvmem cells is very similar to that
provided by i2c_eeprom_partition. "fixed-partition"s for eeproms does
not seem to have made its way into Linux or into any device tree other
than sandbox. It is possible that with the introduction of this API it
would be possible to remove it.

Signed-off-by: Sean Anderson <sean.anderson@seco.com>
2022-06-08 14:00:22 -04:00
Sean Anderson
42f477f0ab misc: i2c_eeprom: Add fallbacks
Add some fallback functions for when i2c_eeprom is disabled. This allows
code to reference i2c_eeprom_* functions without needing to check
whether support has been compiled in.

Signed-off-by: Sean Anderson <sean.anderson@seco.com>
2022-06-08 13:59:53 -04:00
Sean Anderson
dda3b38920 misc: i2c_eeprom: Make i2c_eeprom_write use a const buf
i2c_eeprom_ops->write uses a const buf, so use one for the wrapper
function as well.

Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2022-06-08 13:59:53 -04:00
Sean Anderson
2a5af4049c net: dsa: Fix segmentation fault if master fails to probe
If the DSA master fails to probe for whatever reason, then DSA devices
will continue on as if nothing is wrong. This can cause incorrect
behavior. In particular, on sandbox, dsa_sandbox_probe attempts to
access the master's private data. This is only safe to do if the master
has been probed first. Fix this by probing the master after we look it
up, and bailing out if we get an error.

Fixes: fc054d563b ("net: Introduce DSA class for Ethernet switches")
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
2022-06-08 13:59:53 -04:00
Sean Anderson
e844e5d908 sandbox: Move some mac addresses to device tree
This prevents some conflicts when running sandbox with -D, since the
"rom" mac address will be random and won't match the environment. We
still need to keep addresses for eth1 and eth6 in the environment,
because dm_test_eth_rotate expects to be able to disable them by
removing their envaddr variables. This can likely be fixed in a future
series by adding a function to cause sandbox eth_opts callback for a
particular mac to fail immediately.

Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2022-06-08 13:59:52 -04:00
Sean Anderson
29186884f8 sandbox: Remove eth2addr from environment
DSA interfaces use the same mac address for each interface, unless
instructed otherwise. Just set eth4addr and let eth2addr and eth7addr be
set automatically.

Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2022-06-08 13:59:52 -04:00
Sean Anderson
416e09b906 sandbox: net: Remove fake-host-hwaddr
Instead of reading a pseudo-rom mac address from the device tree, just use
whatever we get from write_hwaddr. This has the effect of using the mac
address from the environment (or from the device tree, if it is
specified).

Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ramon Fried <rfried.dev@gmail.com>
2022-06-08 13:59:52 -04:00
Sean Anderson
df33fd2889 test: eth: Add test for ethernet addresses
This adds a test to make sure that all the ethernet interfaces have
their addresses read properly. At the moment everything is read from the
environment, but the next few commits will add additional sources.

Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2022-06-08 13:59:52 -04:00
Sean Anderson
469a968ac7 sandbox: net: Add mac address for eth8 to environment
The phy_eth0 interface introduced in commit f3dd213e15 ("net: introduce
helpers to get PHY ofnode from MAC") uses a globally-administered
address. Switch to using a locally-administered address, and add it to
the sandbox environment, like the others.

Signed-off-by: Sean Anderson <sean.anderson@seco.com>
2022-06-08 13:59:52 -04:00
Sean Anderson
bedb182e32 sandbox: net: Add aliases for ethernet devices
Commit f3dd213e15 ("net: introduce helpers to get PHY ofnode from MAC")
changed the ethernet sequence assignment from

uclass 36: ethernet
0   * eth@10002000 @ 05813460, seq 0
1   * eth@10003000 @ 05813550, seq 5
2   * sbe5 @ 05813640, seq 3
3   * eth@10004000 @ 05813730, seq 6
4   * dsa-test-eth @ 05813820, seq 4
5   * lan0 @ 05813a30, seq 2
6   * lan1 @ 05813b50, seq 7

to

uclass 36: ethernet
0   * eth@10002000 @ 03813630, seq 0
1   * eth@10003000 @ 03813720, seq 5
2   * sbe5 @ 03813810, seq 3
3   * eth@10004000 @ 03813900, seq 6
4     phy-test-eth @ 038139f0, seq 7
5   * dsa-test-eth @ 03813ae0, seq 4
6   * lan0 @ 03813cf0, seq 2
7   * lan1 @ 03813e10, seq 8

This caused the mac address assignment to switch around. Avoid this in
the future by assigning aliases for all ethernet devices. This reverts
the sequence to what it was before the aformentioned commit (with
phy-test-eth as seq 8). There is no ethernet1 for whatever reason.

Signed-off-by: Sean Anderson <sean.anderson@seco.com>
2022-06-08 13:59:52 -04:00
Tom Rini
c0e63bf468 Merge branch '2022-06-08-virtio-harden-and-test-vring' into next
To quote the author:
Make the virtio ring code resilient against corruption of the buffers
shared with the device.

It follows the example of Linux by keeping a private copy of the
descriptors and metadata for state tracking and only ever writing to the
descriptors that are shared with the device. I was able to test these
hardening steps in the sandbox by simulating device writes to the
queues.
2022-06-08 11:15:28 -04:00
Andrew Scull
d036104a02 test: dm: virtio_rng: Test virtio-rng with faked device
Add a regression test for virtio-rng reading beyond the end of its
buffer if the virtio device provides an invalid length.

Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2022-06-08 09:24:04 -04:00
Andrew Scull
43937a4f5e virtio: rng: Check length before copying
Check the length of data written by the device is consistent with the
size of the buffers to avoid out-of-bounds memory accesses in case
values aren't consistent.

Signed-off-by: Andrew Scull <ascull@google.com>
Cc: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
2022-06-08 09:24:04 -04:00
Andrew Scull
420b3e51f4 test: dm: virtio: Test virtio device driver probing
Once the virtio-rng driver has been bound, probe it to trigger the pre
and post child probe hooks of the virtio uclass driver. Check the status
of the virtio device to confirm it reached the expected state.

Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2022-06-08 09:24:04 -04:00
Andrew Scull
acd3b27a65 virtio: sandbox: Bind RNG rather than block device
The virtio-rng driver is extremely simple, making it suitable for
testing more of the virtio uclass logic. Have the sandbox driver bind
the virtio-rng driver rather than the virtio-blk driver so it can be
used in tests.

Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2022-06-08 09:24:04 -04:00
Andrew Scull
8df508ff3d test: dm: virtio: Split out virtio device tests
Virtio tests that find a child device require the virtio device driver
to be included in the build so it can probe. The sandbox virtio
transport driver currently reports a virtio-blk device so make sure the
corresponding driver is built before running tests that need it.

Signed-off-by: Andrew Scull <ascull@google.com>
2022-06-08 09:24:04 -04:00
Andrew Scull
82c8610a44 test: dm: virtio: Test notify before del_vqs
The virtqueue is passed to virtio_notify() so move the virtqueue
deletion to the end of the test when it's no longer needed. This wasn't
causing any problems because the sandbox virtio transport driver doesn't
do anything for notifications, but it could cause problems if things
change and it was a bad example.

Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2022-06-08 09:24:04 -04:00
Andrew Scull
1674b6c4d8 virtio: sandbox: Fix device features bitfield
The virtio sandbox transport was setting the device features value to
the bit index rather than shifting a bit to the right index. Fix this
using the bit manipulation macros.

Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2022-06-08 09:24:03 -04:00
Andrew Scull
b1fe820b63 dm: test: virtio: Test the virtio ring
The virtio ring is the basis of virtio communication. Test its basic
functionality and its resilience against corruption from the device.

Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2022-06-08 09:24:03 -04:00
Andrew Scull
fbef3f53d4 virtio_ring: Check used descriptors are chain heads
When the device returns used buffers, it should refer to the descriptor
that is the head of the descriptor chain for that buffer. Confirm this
to be the case by tracking the head of descriptor chains that have been
made available to the device.

Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2022-06-08 09:24:03 -04:00
Andrew Scull
10a1453636 virtio_ring: Maintain a shadow copy of descriptors
The shared descriptors should only be written by the guest driver,
however, the device is still able to overwrite and corrupt them.
Maintain a private shadow copy of the descriptors for the driver to
use for state tracking, removing the need to read from the shared
descriptors.

Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2022-06-08 09:24:03 -04:00
Andrew Scull
b0952977c9 virtio_ring: Add helper to attach vring descriptor
Move the logic for attaching a descriptor to its own function.

Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2022-06-08 09:24:03 -04:00
Andrew Scull
68f8bf21c7 virtio_ring: Merge identical variables
The variables `total_sg` and `descs_used` have the same value. Replace
the few uses of `total_sg` with `descs_used` to simplify the situation.

Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2022-06-08 09:24:03 -04:00
Tom Rini
ed1cbbe2af Merge branch '2022-06-07-assorted-improvements' into next
- A wide ranging set of minor clean-ups and improvements
2022-06-07 12:21:57 -04:00