Upcoming Beagle and Overo revisions use POP memory with 256MB or 512MB
per bank. This patches uses the SDRC settings from x-load or the config
header to set up timing properly.
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Using the reset command on OMAP36XX/37XX and OMAP4 caused a hang. This
patch uses the reset bit appropriate for each CPU architecture.
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The workarounds for errata 621766 and 725233 should only be applied
on affected Cortex-A8 revisions. Recent chips use r3px cores where
these have been fixed.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This function consists entirely of inline asm statements, so writing
it directly in a .S file is simpler. Additionally, the inline asm is
not safe as is, since registers are not guaranteed to be preserved
between asm() statements.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
On OMAP34xx ES1.0, the L2 enable bit can only be set in secure mode,
so an SMC call to the ROM monitor is required. On later versions,
and on newer devices, this bit is banked and we can set it directly.
The code checked only the ES revision of the chip, and hence incorrectly
used the ROM call on ES1.0 versions of other devices.
This patch adds a check for chip family as well as revision, and also
removes some code duplication between the enable and disable functions.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch configures clocks properly when a 36XX/37XX
processor is detected.
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
TI has added new processors to the OMAP3 family. This patch enhances
the code in sysinfo.c to detect which family member is present.
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Confiures GPMC timings for both chips and also configures pinmux
for GPIO_65, which is used as the interrupt signal for the second chip
Signed-off-by: Scott Ellis <scott@jumpnowtek.com>
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch enhances the revision detection function and adds
support for the C4 revision. The board revision is printed
and approriate revision specific setup is done automatically.
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The latest Overo COM modules encode their revision number on
GPIOs 115, 113, and 112. All boards to date have no pullups on these pins
and hence appear as revision 0.
This patch reads and prints the revision information.
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Allows one to set the processor clock rate via "setenv mpurate 720" for example
Default is set to a "safe" 500 Mhz.
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch modifies the pinmux setup for MMC1_CLK and MMC3_CLK to enable
the input driver. MMC2_CLK was already properly configured.
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch adds a function to allow one to easily set the target
voltage for the TWL4030 regulators. It also modifies the existing
code to use this new function. Applicable definitions are moved
out of the driver file and into the header file so that they are
generally accessible
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The functions in syslib.c can be shared, so this patch moves it from
cpu/omap3 to cpu/omap-common
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
From the document, if set all arguments in "OUTPUT_FORMAT" to
"tradbigmips", then even add "-EL" to gcc we still get EB format.
pb1x00 is only used in Little-endian, so its default endian should be
set to LE.
Signed-off-by: Xiangfu Liu <xiangfu@openmobilefree.net>
Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>
We need to invalidate the data cache after it has been used as init-ram.
This problem was detected on the lwmon5 update.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch fixes a bug in reconfigure_pll(), where the detection of
the current bootstrap option is wrong. The ICS bits where incorrectly
shifted. This bug was found on the lwmon5 board, which uses bootstrap
option H (I2C bootstrap EEPROM).
Additionally a bit of code was moved into the if statement, since its
only used after later on. No need to run this code all the time.
Also, a few empty lines are added to make the code better readable.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Rupjyoti Sarmah <rsarmah@amcc.com>
Cc: Victor Gallardo <vgallardo@appliedmicro.com>
Opps, after a long time I tested recent u-boot on our
APC405 board. This simple fix makes networking work again.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
This rewrite of the mvtwsi driver is 25% smaller and much
faster and simpler than the previous code.
Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
Acked-by: Prafulla Wadaskar<prafulla@marvell.com>
Acked-by: Heiko Schocher<hs@denx.de>
This driver is not kirkwood-specific and can also be used
e.g. by orion5x. Rename to a SoC-neutral name.
Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
Acked-by: Prafulla Wadaskar<prafulla@marvell.com>
Acked-by: Heiko Schocher<hs@denx.de>
These are not used on this board, which uses soft I2C instead.
Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
Acked-by: Prafulla Wadaskar<prafulla@marvell.com>
Acked-by: Heiko Schocher<hs@denx.de>
Remove the register offset and common defines which are
already present in drivers/i2c/omap24xx.h. All of these
defines carry the same value even.
Cc: Steve Sakoman <steve@sakoman.com>
Cc: Heiko <hs@denx.de>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Wolfang Denk <wd@denx.de>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Steve Sakoman <steve@sakoman.com>
Make the header guard to be generic to stop conflicting with
omap2 i2c header file arch/arm/include/asm/arch-omap24xx/i2c.h
Cc: Steve Sakoman <steve@sakoman.com>
Cc: Heiko <hs@denx.de>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Wolfang Denk <wd@denx.de>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Steve Sakoman <steve@sakoman.com>
fdt_parent_offset() is an expensive operation, so we'd like to reduce
unnecessary calls to it.
Further, the practice of iterating up to the root if address/size cells
aren't found was apparently done for Linux for compatibility with certain
buggy Open Firmware implementations, and U-Boot inherited the code. The
compliant behavior is to treat a missing #address-cells as 2, and a missing
#size-cells as 1 -- never looking anywhere but the immediate parent of the
node of interest.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We currently do not add a cpu-release-addr for core 0, this is needed
when we want to reset core 0 and later restart it from Linux
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There is a limitation (or bug?) of nios2 toolchain. The nios2 gcc
didn't generate correct code when the reset vector is passed as a
constant. It just generated a direct "call", which was wrong when
the reset vector was not located in the same 256MB span as u-boot.
The "Nios II Processor Reference Handbook" said,
"call can transfer execution anywhere within the 256 MByte range
determined by PC31..28. The Nios II GNU linker does not automatically
handle cases in which the address is out of this range."
So we have to use registered "callr" instruction to do the job.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Scott McNutt <smcnutt@psyent.com>
We should check argv[3] only if there are enough args. Otherwise,
it might cause invalid memory access fault.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Scott McNutt <smcnutt@psyent.com>
We get two build errors:
fsl_elbc_nand.c: In function 'fsl_elbc_run_command':
fsl_elbc_nand.c:231: error: 'fsl_lbc_t' has no member named 'lsor'
make[1]: *** [/work/wd/tmp-ppc/drivers/mtd/nand/fsl_elbc_nand.o] Error 1
and
ve8313.c: In function 'initdram':
ve8313.c:104: error: expected '=', ',', ';', 'asm' or '__attribute__'
before '*' token
ve8313.c:104: error: 'lbc' undeclared (first use in this function)
ve8313.c:104: error: (Each undeclared identifier is reported only once
ve8313.c:104: error: for each function it appears in.)
ve8313.c:104: error: 'immap_t' has no member named 'lbus'
make[1]: *** [ve8313.o] Error 1
make: *** [board/ve8313/libve8313.a] Error 2
Due to changes to unifiy local bus struct definitions.
Reported-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
In function board_early_init_r(), serdes will not be initialize yet.
Thus sRIO was always considered disabled. Move the check for sRIO into
misc_init_r() which is called after fsl_serdes_init().
Also, fixed warning associated with gur variable possibly not being
used.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Lian Minghuan <B31939@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
