According to Server Base System Architecture (SBSA) specification,
the SBSA Generic Watchdog has two stage timeouts: the first signal
(WS0) is for alerting the system by interrupt, the second one (WS1) is a
real hardware reset.
More details about the hardware specification of this device:
ARM DEN0029B - Server Base System Architecture (SBSA)
This driver can operate ARM SBSA Generic Watchdog as a single stage
In the single stage mode, when the timeout is reached, your system
will be reset by WS1. The first signal (WS0) is ignored.
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add Root Complex and Endpoint mode specific config entries, such that
it's feasible to enable the RC and/or EP mode driver indepently.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add the PCIe EP mode support for lx2160a-v2 platform.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Modify the ls_pcie_dump_atu function, make it can print the INBOUND
windows registers.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Add the INBOUND configuration for VFs of PF.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Due to the ls2085a and ls2080a use different way to set the BAR size,
so add the BAR size init code here.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The VF_BARn_REG register's Prefetchable and Type bit fields
are overwritten by a write to VF's BAR Mask register.
workaround: Before writing to the VF_BARn_MASK_REG register,
write 0b to the PCIE_MISC_CONTROL_1_OFF register.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add the multiple function support for Layerscape platform, some PEXs
of Layerscaple platform have more than one PF.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Add the PCIe EP node for ls1046a.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Some EP deivces need to initialize before RC scan it, e.g. NXP
layerscape platform, so add the init function in pci_ep uclass.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Split the RC and EP driver, and reimplement the EP driver base on
the EP framework.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
lx2160a rev2 requires 4KB space for type0 and 4KB
space for type1 iATU window. Increase configuration
size to 8KB to have sufficient space for type0
and type1 window.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
- Drop ifdef CONFIG_SYS_I2C to initialize
baudrate of i2c
- Drop warning of i2c_early_init_f as follows,
warning: implicit declaration of function 'i2c_early_init_f'; did you
mean 'arch_early_init_r'? [-Wimplicit-function-declaration]
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Enable secure system counter in board_early_init_f for udelay()
to fix a bug that always return 0 by timer_read_counter()
when boot from qspi(No TFA)
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
- Drop ifdef CONFIG_SYS_I2C to initialize
baudrate of i2c
- Drop warning of i2c_early_init_f as follows,
warning: implicit declaration of function 'i2c_early_init_f'; did you
mean 'arch_early_init_r'? [-Wimplicit-function-declaration]
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Enable secure system counter in board_early_init_f for udelay()
to fix a bug that always return 0 by timer_read_counter()
when boot from qspi(No TFA)
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Move i2c_early_init_f to common function
to initialize baudrate of i2c
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Register the random number generator with the rng subsystem in u-boot.
This way it can be used by EFI as well as for the 'rng' command.
Signed-off-by: Michael Walle <michael@walle.cc>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
If it is already instantiated tear it down first and then reinstanciate
it again with prediction resistance.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The secure keys (TDKEK, JDKEK, TDSK) can only be generated once after a
POR. Otherwise the RNG4 will throw an error.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Since Era 10, the version registers changed. Add the version registers
and use them on newer modules.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
We need the era in other modules, too. For example, to get the RNG
version.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Align the status line with all the other output in U-Boot.
Before the change:
DDR 3.9 GiB (DDR3, 32-bit, CL=11, ECC on)
SEC0: RNG instantiated
WDT: Started with servicing (60s timeout)
After the change:
DDR 3.9 GiB (DDR3, 32-bit, CL=11, ECC on)
SEC0: RNG instantiated
WDT: Started with servicing (60s timeout)
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The value 0 assigned to final is overwritten before ever being used.
Remove the assignment.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The sequence of arguments should match the format string.
For printing unsigned numbers we should use %u.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The workaround has been implemented in PBI phase, so remove
the duplicated implementation from U-Boot.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Previous attempt to increase CONFIG_SYS_MALLOC_LEN was done in commit
c084a8edf4 ("configs: ls1012a: Increase CONFIG_SYS_MALLOC_LEN size")
which increased malloc memory to ~1M.
PFE firmware alone requires 3M of dynamic memory allocation and
therefore, increase the config value to a larger value i.e 5M. This size
should be enough as of now to accommodate further memory requirements.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add support for SDHC adapter identification and configuration
during board init.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The eSDHC adapter card identification and multiplexing configuration
through FPGA had been implemented in both common mmc driver and
fsl_esdhc driver. However it is proper to move these code to board
files and do it during board initialization. The FPGA registers are
also board specific.
This patch is to move eSDHC adapter card identification and
multiplexing configuration from mmc driver to specific board files.
And the option CONFIG_FSL_ESDHC_ADAPTER_IDENT is no longer needed.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
[Rebased, Removed T1040QDS change as board does not exist]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
The sdhc_adapter of global data has not been used, and we
do not have to use it as global data even we may need it
in the future.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add xspi boot source to qixis command to let the soc boot from
flex-nor flash chip.
Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The correct setting for the RGMII ports on LS1012ARDB is to
enable delay on both Rx and Tx so the interface mode used should
be PHY_INTERFACE_MODE_RGMII_ID
Signed-off-by: Chaitanya Sakinam <chaitanya.sakinam@nxp.com>
Signed-off-by: Anji J <anji.jagarlmudi@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Remove "fdt_high" environment variable to use the bootm_size
to safely contain a kernel, device tree and initrd for
relocation.
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
On aarch64 running with dcache off, will result in an unaligned access
exception:
=> dcache off
=> hash sha1 $kernel_addr_r 100
"Synchronous Abort" handler, esr 0x96000061
elr: 00000000960317d8 lr : 00000000960316a4 (reloc)
elr: 00000000fbd787d8 lr : 00000000fbd786a4
[..]
The compiler emits a "stur x1, [x0, #12]". x1 is might just be 32 bit
aligned pointer. Remove the unused u64 element from the union to drop
the minimal alignment to 32 bit. Also remove the union, because it is
no more needed.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This enables SYS_I2C_MXC to fix a bug that
failed to boot from sd card with
image u-boot-with-spl-pbl.bin
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
There are two issues:
(1) The spin table doesn't convert the endianness of the jump address.
Although there is code for it, the result isn't used at all (x0).
(2) If something goes wrong, the function returns. But that doesn't
make sense at all.
Use the actual converted jump address as destination to fix. If
there is an error, jump to a trap loop. And rearrange the code exception
level switching code to make it smaller and clearer.
This reduces the size of the spin table code section from 696 bytes to
424 bytes. If CONFIG_ARMV8_SWITCH_TO_EL1 the code size reduced from 696
bytes to 632 bytes.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
On ARM64, a 64kb region is reserved for the runtime services code.
Unfortunately, this code overlaps with the spin table code, which also
needs to be reserved. Thus now that the code is relocatable, allocate a
new page from EFI, copy the spin table code into it, update any pointers
to the old region and the start the secondary CPUs.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add a new variable secondary_boot_code_start, which holds a pointer to
the start of the spin table code. This will help to relocate the code
section. While at it, move the size variable from the end to the
beginning so there is a common section for the variables. Remove any
other symbols.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Now that the spin table is in a separate module, this is no longer
necessary. Drop it.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This function is not used outside the module. Make it static.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
There is no need to cast around. Assign the address to the local
variable and use it.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Only the PowerPC architecture needs this function. Remove it.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Fix the alignment so it will match the comments. The spin table has to
be 8 byte aligned, so ".align 3" is enough.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Don't use LDR to load a pointer to a function. This will generate a
literal which cannot be relocated. Use ADR which is PC-relative and
therefore can easily be relocated.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Move it out of lowlevel.S into spintable.S. On layerscape, the secondary
CPUs are brought up in main u-boot. This will make it possible to only
compile the spin table code for the main u-boot and omit it in SPL.
This saves about 720 bytes in the SPL.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The generic armv8 code already has support to bring up the secondary
cores. Thus, don't hardcode the jump in the layerscape lowlevel_init to
the spin table code; instead just return early and let the common armv8
code handle the jump. This way we can actually use the CPU_RELEASE_ADDR
feature.
Signed-off-by: Michael Walle <michael@walle.cc>
[Rebased, Removed kontron_sl28.h change as file does not exist]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
