On the Yocto image there is a single partition and the kernel
and dtb are present in the 'boot' directory.
Change it accordingly so that the board can boot the Yocto
image by default.
Use the generic 'load' command instead, which is able to
read from an ext4 partition.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Add LVDS support for DLC0700XDP21LF 7in 1024x600 display
(equivalent to the DLC-700JMGT4 with new touch controller)
Signed-off-by: Robert Jones <rjones@gateworks.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
In the default pulse-skipping mode regulators that are very lightly
loaded can fail to regulate properly. Switching them to always use
continuous mode causes only around 10mW of overall system power
difference in a lightly loaded system that isn't already operating
them in continuous mode.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
In the default 'auto' mode regulators that are very lightly loaded
can be put in PFM mode and fail to regulator properly. Switching them
to always use continuous PWM mode has a neglibable affect on system
power and garuntees proper regulation under lightly loaded circumstances.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Substitutions in EOL parts changes the VDD_2P5 voltage rail such that
the previously unused VGEN6 LDO is needed in place of the lower power
VGEN5 for the GW54xx-G.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
For some time now having USB_KEYBOARD support has caused usb to be
initialized on boot. To allow for a quicker bootup we don't want this
for Ventana and don't really need USB keyboard support so remove it.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Some IPs have their accessible address space restricted by the
interconnect. Let's make sure U-Boot only ever uses the space below
the 4G address boundary (which is 3GiB big), even when the effective
available memory is bigger.
We implement board_get_usable_ram_top() for all i.MX8M SoCs, as the
whole family is affected by this.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
The MX25V8035F is a 8Mb SPI NOR flash and the MX25R1635F is very
similar, but has twice the size (16Mb) and supports a wider supply
voltage range.
They were tested on the Kontron Electronics i.MX6UL and i.MX8MM SoMs.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
As seen with clang-12:
warning: __asm_invalidate_l3_dcache changed binding to STB_WEAK
As we indeed use ENTRY and then declare the function weak manually. Use
the WEAK declarative from <linux/linkage.h> instead.
Signed-off-by: Tom Rini <trini@konsulko.com>
On arm64, board info is not applicable and kernel command line patched into
the DT, so the LMB reservation here makes no sense anymore. On legacy arm32,
this might still be necessary on systems which do not use DT or use legacy
ATAGS. Disable this LMB reservation on arm64.
This also permits Linux DT to specify reserved memory node at address close
to the end of DRAM bank, i.e. overlaping with U-Boot location. Since after
boot, U-Boot will be no more, this is OK.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hai Pham <hai.pham.ud@renesas.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Tom Rini <trini@konsulko.com>
Fix following compilation issue when SYS_DCACHE_OFF is enable:
drivers/misc/scmi_agent.c:128: undefined reference to `mmu_set_region_dcache_behaviour'
when SYS_DCACHE_OFF is enable, mmu_set_region_dcache_behaviour() must be
defined.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
On implementations that support VHE, the layout of the CPTR_EL2
register depends on whether HCR_EL2.E2H is set. If the bit is
set, CPTR_EL2 uses the same layout as CPACR_EL1 and can in fact
be accessed through that register. In that case, jump to the
EL1 code to enable access to the FP/SIMD registers. This allows
U-Boot to run on systems that pass control to U-Boot in EL2 with
EL2 Host mode enabled such as machines using Apple's M1 SoC.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Acked-by: Marc Zyngier <maz@kernel.org>
The cavium,bdk node is a non-standard dt node used by the BDK and
therefore it is removed from the dt before booting Linux. Do not
require this node to exist as it won't for standard dt's.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Extend CONFIG_SYS_BAUDRATE_TABLE and include all standard baudrates and
also nonstandard up to the 6 MBaud. U-Boot's A3720 UART driver can use
baudrates from 300 Baud to 6 MBaud.
This changes all A3720 boards, since all of them include either
mvebu_armada-37xx.h or turris_mox.h config file.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Unfortunately the UART driver in current Linux for Armada 3700 expects
UART's parent clock to be XTAL and calculats baudrate divisor according
to XTAL clock. Therefore we must switch back to XTAL clock before
booting kernel.
Implement .remove method for this driver with DM_FLAG_OS_PREPARE flag
set.
If current baudrate is unsuitable for XTAL clock then we do not change
anything. This can only happen if the user either configured unsupported
settings or knows what they are doing and has kernel patches which allow
usage of non-XTAL parent clock.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Using TBG clock as parent clock for UART allows us using higher
baudrates than 230400.
Turris MOX with external FT232RL USB-UART works fine up to 3 MBaud
(which is maximum for this USB-UART controller), while EspressoBIN with
integrated pl2303 USB-UART also works fine up to 6 MBaud.
Slower baudrates with TBG as a parent clock can be achieved by
increasing TBG dividers and oversampling divider. When using the slowest
TBG clock, minimal working baudrate is 300.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Setting DM_FLAG_PRE_RELOC for Armada 3720 clock drivers (TBG and
peripheral clocks) makes it possible for serial driver to retrieve clock
rates via clk API.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
UART parent clock is by default the platform's xtal clock, which is
25 MHz.
The value defined in the driver, though, is 25.8048 MHz. This is a hack
for the suboptimal divisor calculation
Divisor = UART clock / (16 * baudrate)
which does not use rounding division, resulting in a suboptimal value
for divisor if the correct parent clock rate was used.
Change the code for divisor calculation to round to closest value, i.e.
Divisor = Round(UART clock / (16 * baudrate))
and change the parent clock rate value to that returned by
get_ref_clk().
This makes A3720 UART stable at standard UART baudrates between 1800 and
230400.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
With the spear family of platforms gone, remove references to them from
the build jobs.
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
While this platform has not yet been converted, there is active efforts
to do so. Keep the platform for now.
This reverts commit aa697e6904.
Signed-off-by: Tom Rini <trini@konsulko.com>
- Remove a large number of platforms that did not migrate to DM_PCI or
DM_USB by 2 years past the migration deadline and do not have a
migration imminent.
If MUSB support is disabled, these parts of the code will fail to build.
Cc: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove them. As this is
the last of the SPEAr platforms, so remove the rest of the remaining
support as well.
Cc: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove them. As this is
also the last SPEAR3XX platform, remove that symbol as well.
Cc: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove them.
Cc: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove them.
Cc: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove it
Cc: Gerald Kerma <dreagle@doukki.net>
Cc: Tony Dinh <mibodhi@gmail.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove it
Cc: Ajay Bhargav <contact@8051projects.net>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove it.
This is also the last PL010_SERIAL using board, so remove those
references.
Cc: Sergey Kostanbaev <sergey.kostanbaev@fairwaves.ru>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove them.
Cc: Andreas Bießmann <andreas@biessmann.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
As this board does not use CONFIG_OF_CONTROL and the DM_USB migration
deadline has passed, disable USB_GADGET support.
Cc: Eric Nelson <eric@nelint.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Eric Nelson <eric@nelint.com>
As these boards support CONFIG_OF_CONTROL today, perform a basic
CONFIG_DM migration.
Cc: Eric Cooper <ecc@cmu.edu>
Signed-off-by: Tom Rini <trini@konsulko.com>
As these boards support CONFIG_OF_CONTROL today, perform a basic
CONFIG_DM migration.
Cc: Luka Perkov <luka@openwrt.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
As these boards support CONFIG_OF_CONTROL today, perform a basic
CONFIG_DM migration.
Cc: Luka Perkov <luka@openwrt.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
As these boards support CONFIG_OF_CONTROL today, perform a basic
CONFIG_DM migration.
Cc: Dave Purdy <david.c.purdy@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
As these boards support CONFIG_OF_CONTROL today, perform a basic
CONFIG_DM migration.
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not converted to DM_USB by the deadline, disable USB
support as they do not enable CONFIG_OF_CONTROL.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
